[CentOS] Re: Network routes

Jason Pyeron jpyeron at pdinc.us
Wed Jan 30 01:27:10 UTC 2008




  _____  

From: centos-bounces at centos.org [mailto:centos-bounces at centos.org] On Behalf
Of Ross S. W. Walker
Sent: Tuesday, January 29, 2008 18:22
To: centos at centos.org
Subject: Re: [CentOS] Re: Network routes





Sorry for the top post.

The default route is the route applied when no other route matches the
destination IP. From that how would you figure out which default route to
pick, only if the routes were weighted could you pick between two.

If you had two routes with equal weight and the traffic went round robin
between them then the originating host will discard half the returning
traffic because it's not coming from the same ip it sent it to.

No your best bet is probably to do reverse NAT'ing as it is simple to setup
and you don't have to worry about default routes and weight. Traffic
initiates on 1 gateway and sticks with it for the duration of the session.
You can use BGP on the gateways outside interface to load balance or
fail-over the default gateway or use round-robin DNS, MX records for mail,
etc.

-Ross

 

Okay, they were weighted primay at 0 and it worked. Secondary at 20, it
would never be chosen as a default. But how does a reply get out to the net
on the same route it came in on?

 

 
----- Original Message -----
From: centos-bounces at centos.org <centos-bounces at centos.org>
To: centos at centos.org <centos at centos.org>
Sent: Tue Jan 29 18:03:13 2008
Subject: [CentOS] Re: Network routes

on 1/29/2008 2:53 PM Jason Pyeron spake the following:
> 
>
>> -----Original Message-----
>> From: centos-bounces at centos.org
>> [ <mailto:centos-bounces at centos.org> mailto:centos-bounces at centos.org] On
Behalf Of Ross S. W. Walker
>> Sent: Tuesday, January 29, 2008 17:38
>> To: CentOS mailing list
>> Subject: RE: [CentOS] Network routes
>>
>> Jason Pyeron wrote:
>>> I am unable to ping NE.TW.RKB.IP1 from an outside network.
>>> Other machines
>>> which do not have access or routes for NET.WOR.KA.0 respond
>> just fine.
>>> How do I get it to respond on both NET.WOR.KA.0 and
>>> NE.TW.RKB.0 given all
>>> default traffic should go through  NET.WOR.KA.1  unless it is
>>> in reply to
>>> traffic from NE.TW.RKB.1 or there is an outage.
>>>
>>> [root at host20 ~]# route -n
>>> Kernel IP routing table
>>> Destination     Gateway         Genmask         Flags Metric
>>> Ref    Use
>>> Iface
>>> NET.WOR.KA.0    0.0.0.0         255.255.255.0   U     0     
>>> 0        0 eth1
>>> 192.168.1.0     0.0.0.0         255.255.255.0   U     0     
>>> 0        0 eth0
>>> NE.TW.RKB.0     0.0.0.0         255.255.255.0   U     0     
>>> 0        0 eth0
>>> 169.254.0.0     0.0.0.0         255.255.0.0     U     0     
>>> 0        0 eth1
>>> 0.0.0.0         NET.WOR.KA.1    0.0.0.0         UG    0     
>>> 0        0 eth1
>>> 0.0.0.0         NE.TW.RKB.1     0.0.0.0         UG    20    
>>> 0        0 eth0
>>>
>>> [root at host20 ~]# ifconfig
>>> eth0      Link encap:Ethernet  HWaddr 00:17:31:0F:04:AE
>>>           inet addr:NE.TW.RKB.IP1  Bcast:NE.TW.RKB.255 
>>> Mask:255.255.255.0
>>> eth0:pn   Link encap:Ethernet  HWaddr 00:17:31:0F:04:AE
>>>           inet addr:192.168.1.20  Bcast:192.168.1.255 
>>> Mask:255.255.255.0
>>> eth1      Link encap:Ethernet  HWaddr 00:01:03:E9:42:D0
>>>           inet addr:NET.WOR.KA.IP2  Bcast:NET.WOR.KA.255 
>>> Mask:255.255.255.0
>>> lo        Link encap:Local Loopback
>>>           inet addr:127.0.0.1  Mask:255.0.0.0
>>>
>> You can have only 1 default route.
>>
>> You can use RIP or some other routing protocol to
>> advertise defualt routes to the host from the
>> gateways based upon route availability or weight,
>> or you can deploy reverse NAT'ing on the gateways
>> so external IPs will be masqueraded as the
>> internal IP of the gateway and thus be routed to
>> the appropriate gateway based on which IP they
>> arrived on.
>>
>> -Ross
>>
>
> But I have 2 physical network cards, on 2 different networks. Should they
> not both have default routes?
>
You would think so, but it will confuse the system so bad that traffic won't
know where to go. The default route is the route that packets need to take
to
leave your network to enter the outside world. Every thing under your
control
should have static routes of some kind, or a routing daemon.
 

 
 

-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-
-                                                               -
- Jason Pyeron                      PD Inc.  <http://www.pdinc.us/>
http://www.pdinc.us -
- Sr. Consultant                    10 West 24th Street #100    -
- +1 (443) 269-1555 x333            Baltimore, Maryland 21218   -
-                                                               -
-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-

This message is for the designated recipient only and may contain
privileged, proprietary, or otherwise private information. If you
have received it in error, purge the message from your system and
notify the sender immediately.  Any other use of the email by you
is prohibited. 

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.centos.org/pipermail/centos/attachments/20080129/f18f3bd6/attachment.html>


More information about the CentOS mailing list