[CentOS] LiveCD System recovery - Mounting LVM?
Gregory P.. Ennis
PoMec at PoMec.Net
Fri Feb 4 01:50:59 UTC 2011
On Sat, Jan 8, 2011 at 7:17 PM, Johan Martinez <jmartiee at gmail.com>
wrote:
On Sat, Jan 8, 2011 at 3:50 PM, Lamar Owen <lowen at pari.edu>
wrote:
On Saturday, January 08, 2011 04:27:39 pm Johan Martinez
wrote:
> Now I am booting of CentOS live cd for system restore.
I recreated
> partitions like previous system using fdisk and then
used dd to dump all the
> data onto it. I would like to mount sda2 as LVM, but I
don't know how to do
> that. Any steps or howto mount LVM manually would be
really helpful. I think
> I can recover the system once I am able to access sda1
and sda2. Any help?
pvscan
vgscan
vgchange -ay
lvscan
(It has been awhile since I have done this; I know the
vgchange -ay is required, but I don't recall if pvscan
and lvscan were required or if I just used them for
information....but I do think the vgscan was required.)
In the lvscan output you should see the logical volumes;
mount to the desired mountpoint with
mount /dev/VOLUMEGROUP/LOGICALVOLUME MOUNTPOINT
Or you can reboot the CentOS disk in rescue mode and
have it find your system as part of its bootup. In that
case your system will be mounted under /mnt/sysimage and
you can do a 'chroot /mnt/sysimage' and essentially get
a command line inside that system.
Hope that helps.
_______________________________________________
CentOS mailing list
CentOS at centos.org
http://lists.centos.org/mailman/listinfo/centos
Thanks for the reply Lamar and Robert.
I had tried pvscan and vgscan before sending out my first
mail, but it didn't show up any physical volumes and vol
grpups.
I didn't do lvscan though.
I will try again and see how it goes.
jM.
I can see PVs sda1 and sda2 with pvscan, but they are not getting
mounted as lvm. Also, I see sda2 listed as LVM although I didn't
partition it that way. e.g. fdisk shows it as Linux type and pvscan is
showing it as lvm2. That's somewhat confusing me.
Also, the real problem for me is recovery. I don't see LVM mounted after
doing vgscan and lvscan. Am I missing something here? Any help?
Thanks you..
jM
------------------------------------------------------------------------
Johan,
I have the same circumstance, and have not been able to mount an lvm
volume to a new machine. I have your posts, but have not been able to
mount the lvm either. Did you ever get this resolved? Sure would
appreciate your thoughts, or any one else that has been able to do this.
Greg
-------------------------------------------
Johan,
I am not sure if this is your problem but what I can determine is that
there may be a conflict with the same names of the lvm volumes; ie the
old volume that I am trying to mount has the same name as the volume on
the machine that is active.
[root at SeVi mnt]# pvscan
PV /dev/hdc2 VG VolGroup00 lvm2 [37.16 GB / 0 free]
PV /dev/hdd1 VG VolGroup00 lvm2 [186.28 GB / 0 free]
PV /dev/sda2 VG VolGroup00 lvm2 [931.41 GB / 0 free]
Total: 3 [1.13 TB] / in use: 3 [1.13 TB] / in no VG: 0 [0 ]
[root at SeVi mnt]# lvchange --available y /dev/VolGroup00/LogVol00
[root at SeVi mnt]# mount /dev/VolGroup00/LogVol00 /mnt/hdc2
This results in mounting the current machine's lvm which is on sda1, but
I am wanting to mount /dev/hdc2.
Any one have any ideas ?
Greg
More information about the CentOS
mailing list