Hallo,
habe CentOS 6.5 x64, an diesem Rechner habe ich eine USB-Platte auf die
mein Backup Programm Sicherungen macht.
Diese Platte hört plötzlich auf zu funktionieren und ist auch erst
wieder nach einem Reboot nutzbar.
Wenn ich die Platte tausche und eine andere anschliesse dann wird diese
auch, bis zum Reboot, nicht erkannt.
dmesg spuckt folgendes aus:
usb 2-1.5: USB disconnect, device number 4
usb 2-1.5: new high speed USB device number 5 using ehci_hcd
usb 2-1.5: New USB device found, idVendor=1759, idProduct=5000
usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1.5: Product: MassStorage Device
usb 2-1.5: Manufacturer: USB 3.0
usb 2-1.5: SerialNumber: 73K4S4RGS
usb 2-1.5: configuration #1 chosen from 1 choice
scsi8 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 5
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 8:0:0:0: Direct-Access USB 3.0 LucidPort USB300 0100 PQ: 0
ANSI: 4
sd 8:0:0:0: Attached scsi generic sg3 type 0
sd 8:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 8:0:0:0: [sdc] Write Protect is off
sd 8:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 8:0:0:0: [sdc] Assuming drive cache: write through
sd 8:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 8:0:0:0: [sdc] Assuming drive cache: write through
sd 8:0:0:0: [sdc] Attached SCSI disk
EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
...
ganz viel davon
...
EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
usb 2-1.5: USB disconnect, device number 5
usb 2-1.5: new high speed USB device number 6 using ehci_hcd
usb 2-1.5: New USB device found, idVendor=1759, idProduct=5000
usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3
usb 2-1.5: Product: MassStorage Device
usb 2-1.5: Manufacturer: USB 3.0
usb 2-1.5: SerialNumber: WD-WX71A8295652
usb 2-1.5: configuration #1 chosen from 1 choice
scsi9 : SCSI emulation for USB Mass Storage devices
usb-storage: device found at 6
usb-storage: waiting for device to settle before scanning
usb-storage: device scan complete
scsi 9:0:0:0: Direct-Access USB 3.0 LucidPort USB300 0100 PQ: 0
ANSI: 4
sd 9:0:0:0: Attached scsi generic sg3 type 0
sd 9:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB)
sd 9:0:0:0: [sdc] Write Protect is off
sd 9:0:0:0: [sdc] Mode Sense: 03 00 00 00
sd 9:0:0:0: [sdc] Assuming drive cache: write through
sd 9:0:0:0: [sdc] Assuming drive cache: write through
sdc: sdc1
sd 9:0:0:0: [sdc] Assuming drive cache: write through
sd 9:0:0:0: [sdc] Attached SCSI disk
EXT4-fs (sdc1): recovery complete
EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts:
hub 2-1:1.0: cannot reset port 5 (err = -110)
hub 2-1:1.0: cannot reset port 5 (err = -110)
hub 2-1:1.0: cannot reset port 5 (err = -110)
hub 2-1:1.0: cannot reset port 5 (err = -110)
hub 2-1:1.0: cannot reset port 5 (err = -110)
hub 2-1:1.0: Cannot enable port 5. Maybe the USB cable is bad?
hub 2-1:1.0: cannot disable port 5 (err = -110)
hub 2-1:1.0: cannot reset port 5 (err = -110)
usb 2-1.5: reset high speed USB device number 6 using ehci_hcd
ehci_hcd 0000:00:1d.0: fatal error
ehci_hcd 0000:00:1d.0: HC died; cleaning up
ehci_hcd 0000:00:1d.0: force halt; handhake ffffc9000306e024 00004000
00004000 -> -110
ehci_hcd 0000:00:1d.0: HC died; cleaning up
usb 2-1: USB disconnect, device number 2
usb 2-1.2: USB disconnect, device number 3
usb 2-1.5: device descriptor read/all, error -19
hub 2-1:1.0: cannot disable port 5 (err = -19)
hub 2-1:1.0: cannot disable port 5 (err = -19)
sd 9:0:0:0: Device offlined - not ready after error recovery
sd 9:0:0:0: [sdc] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK
sd 9:0:0:0: [sdc] CDB: Write(10): 2a 00 12 9e 3d 48 00 00 08 00
end_request: I/O error, dev sdc, sector 312360264
Buffer I/O error on device sdc1, logical block 39044777
lost page write due to I/O error on sdc1
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: [sdc] killing request
sd 9:0:0:0: rejecting I/O to offline device
...
ganz viel davon
...
sd 9:0:0:0: rejecting I/O to offline device
JBD2: Detected IO errors while flushing file data on sdc1-8
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: rejecting I/O to offline device
sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK
sd 9:0:0:0: [sdc] CDB: Write(10): 2a 00 12 85 54 20 00 00 10 00
end_request: I/O error, dev sdc, sector 310727712
sd 9:0:0:0: rejecting I/O to offline device
...
ganz viel davon
...
sd 9:0:0:0: rejecting I/O to offline device
EXT4-fs (sdc1): delayed block allocation failed for inode 12 at logical
offset 36534272 with max blocks 2048 with error -5
This should not happen!! Data will be lost
sd 9:0:0:0: rejecting I/O to offline device
...
extrem viel davon
...
sd 9:0:0:0: rejecting I/O to offline device
Aborting journal on device sdc1-8.
sd 9:0:0:0: rejecting I/O to offline device
JBD2: I/O error detected when updating journal superblock for sdc1-8.
JBD2: Detected IO errors while flushing file data on sdc1-8
usb 2-1.5: USB disconnect, device number 6
EXT4-fs error (device sdc1): ext4_journal_start_sb: Detected aborted
journal
EXT4-fs (sdc1): Remounting filesystem read-only
EXT4-fs (sdc1): ext4_da_writepages: jbd2_start: 8192 pages, ino 12; err -30
EXT4-fs error (device sdc1): ext4_read_block_bitmap: Cannot read block
bitmap - block_group = 2260, block_bitmap = 73924612
EXT4-fs error (device sdc1): ext4_discard_preallocations: Error reading
block bitmap for 2260
Buffer I/O error on device sdc1, logical block 0
lost page write due to I/O error on sdc1
EXT4-fs error (device sdc1): ext4_put_super: Couldn't clean up the journal
kann mir da jemand auf die Sprünge helfen?
Der Server läuft an sich durch, nur wenn die Platten wieder nicht
erkannt werden muss ich neu starten.
Danke
Jürgen