Hi,
also das sind 6 Platten, jeden Tag ne andere.
Mal fällt der Montag aus, mal der Mittwoch usw.
Wirklich das Board?
Das wär ärgerlich, da das Teil noch kein Jahr alt. Server Komponente....
Menno :(
Am 05.11.2014 16:00, schrieb Frank Büttner:
Huhu, spontan würde ich mal drauf tippen, das der USB Port oder sogar ein Teil vom USB Controller die Hufe hoch gerissen hat. Wie verhält sich denn die Platte an einem anderen System?
Gruß Frank Am 05.11.2014 um 12:41 schrieb J. Echter:
Hallo,
habe CentOS 6.5 x64, an diesem Rechner habe ich eine USB-Platte auf die mein Backup Programm Sicherungen macht.
Diese Platte hört plötzlich auf zu funktionieren und ist auch erst wieder nach einem Reboot nutzbar.
Wenn ich die Platte tausche und eine andere anschliesse dann wird diese auch, bis zum Reboot, nicht erkannt.
dmesg spuckt folgendes aus:
usb 2-1.5: USB disconnect, device number 4 usb 2-1.5: new high speed USB device number 5 using ehci_hcd usb 2-1.5: New USB device found, idVendor=1759, idProduct=5000 usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1.5: Product: MassStorage Device usb 2-1.5: Manufacturer: USB 3.0 usb 2-1.5: SerialNumber: 73K4S4RGS usb 2-1.5: configuration #1 chosen from 1 choice scsi8 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 5 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 8:0:0:0: Direct-Access USB 3.0 LucidPort USB300 0100 PQ: 0 ANSI: 4 sd 8:0:0:0: Attached scsi generic sg3 type 0 sd 8:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB) sd 8:0:0:0: [sdc] Write Protect is off sd 8:0:0:0: [sdc] Mode Sense: 03 00 00 00 sd 8:0:0:0: [sdc] Assuming drive cache: write through sd 8:0:0:0: [sdc] Assuming drive cache: write through sdc: sdc1 sd 8:0:0:0: [sdc] Assuming drive cache: write through sd 8:0:0:0: [sdc] Attached SCSI disk EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: ... ganz viel davon ... EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: usb 2-1.5: USB disconnect, device number 5 usb 2-1.5: new high speed USB device number 6 using ehci_hcd usb 2-1.5: New USB device found, idVendor=1759, idProduct=5000 usb 2-1.5: New USB device strings: Mfr=1, Product=2, SerialNumber=3 usb 2-1.5: Product: MassStorage Device usb 2-1.5: Manufacturer: USB 3.0 usb 2-1.5: SerialNumber: WD-WX71A8295652 usb 2-1.5: configuration #1 chosen from 1 choice scsi9 : SCSI emulation for USB Mass Storage devices usb-storage: device found at 6 usb-storage: waiting for device to settle before scanning usb-storage: device scan complete scsi 9:0:0:0: Direct-Access USB 3.0 LucidPort USB300 0100 PQ: 0 ANSI: 4 sd 9:0:0:0: Attached scsi generic sg3 type 0 sd 9:0:0:0: [sdc] 625142448 512-byte logical blocks: (320 GB/298 GiB) sd 9:0:0:0: [sdc] Write Protect is off sd 9:0:0:0: [sdc] Mode Sense: 03 00 00 00 sd 9:0:0:0: [sdc] Assuming drive cache: write through sd 9:0:0:0: [sdc] Assuming drive cache: write through sdc: sdc1 sd 9:0:0:0: [sdc] Assuming drive cache: write through sd 9:0:0:0: [sdc] Attached SCSI disk EXT4-fs (sdc1): recovery complete EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: EXT4-fs (sdc1): mounted filesystem with ordered data mode. Opts: hub 2-1:1.0: cannot reset port 5 (err = -110) hub 2-1:1.0: cannot reset port 5 (err = -110) hub 2-1:1.0: cannot reset port 5 (err = -110) hub 2-1:1.0: cannot reset port 5 (err = -110) hub 2-1:1.0: cannot reset port 5 (err = -110) hub 2-1:1.0: Cannot enable port 5. Maybe the USB cable is bad? hub 2-1:1.0: cannot disable port 5 (err = -110) hub 2-1:1.0: cannot reset port 5 (err = -110) usb 2-1.5: reset high speed USB device number 6 using ehci_hcd ehci_hcd 0000:00:1d.0: fatal error ehci_hcd 0000:00:1d.0: HC died; cleaning up ehci_hcd 0000:00:1d.0: force halt; handhake ffffc9000306e024 00004000 00004000 -> -110 ehci_hcd 0000:00:1d.0: HC died; cleaning up usb 2-1: USB disconnect, device number 2 usb 2-1.2: USB disconnect, device number 3 usb 2-1.5: device descriptor read/all, error -19 hub 2-1:1.0: cannot disable port 5 (err = -19) hub 2-1:1.0: cannot disable port 5 (err = -19) sd 9:0:0:0: Device offlined - not ready after error recovery sd 9:0:0:0: [sdc] Result: hostbyte=DID_ABORT driverbyte=DRIVER_OK sd 9:0:0:0: [sdc] CDB: Write(10): 2a 00 12 9e 3d 48 00 00 08 00 end_request: I/O error, dev sdc, sector 312360264 Buffer I/O error on device sdc1, logical block 39044777 lost page write due to I/O error on sdc1 sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: [sdc] killing request sd 9:0:0:0: rejecting I/O to offline device ... ganz viel davon ... sd 9:0:0:0: rejecting I/O to offline device JBD2: Detected IO errors while flushing file data on sdc1-8 sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: rejecting I/O to offline device sd 9:0:0:0: [sdc] Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK sd 9:0:0:0: [sdc] CDB: Write(10): 2a 00 12 85 54 20 00 00 10 00 end_request: I/O error, dev sdc, sector 310727712 sd 9:0:0:0: rejecting I/O to offline device ... ganz viel davon ... sd 9:0:0:0: rejecting I/O to offline device EXT4-fs (sdc1): delayed block allocation failed for inode 12 at logical offset 36534272 with max blocks 2048 with error -5
This should not happen!! Data will be lost sd 9:0:0:0: rejecting I/O to offline device ... extrem viel davon ... sd 9:0:0:0: rejecting I/O to offline device Aborting journal on device sdc1-8. sd 9:0:0:0: rejecting I/O to offline device JBD2: I/O error detected when updating journal superblock for sdc1-8. JBD2: Detected IO errors while flushing file data on sdc1-8 usb 2-1.5: USB disconnect, device number 6 EXT4-fs error (device sdc1): ext4_journal_start_sb: Detected aborted journal EXT4-fs (sdc1): Remounting filesystem read-only EXT4-fs (sdc1): ext4_da_writepages: jbd2_start: 8192 pages, ino 12;
err -30
EXT4-fs error (device sdc1): ext4_read_block_bitmap: Cannot read block bitmap - block_group = 2260, block_bitmap = 73924612 EXT4-fs error (device sdc1): ext4_discard_preallocations: Error reading block bitmap for 2260 Buffer I/O error on device sdc1, logical block 0 lost page write due to I/O error on sdc1 EXT4-fs error (device sdc1): ext4_put_super: Couldn't clean up the
journal
kann mir da jemand auf die Sprünge helfen?
Der Server läuft an sich durch, nur wenn die Platten wieder nicht erkannt werden muss ich neu starten.
Danke
Jürgen