Hola a tod@s!!
Me acaba de surgir un problema con mi programa de fax hylafax, el problema solo lo tengo en el envío, la recepción de faxes funciona correctamente.
Buscando por google encuentro información pero no me queda nada claro que parece un error en el hardware o una mala configuración de la herramienta. La cuestión es que lo tenia funcionando y ahora me lanza estos errores:
MODEM: Conceptronic C56EW externo.
Product code (ATI0) is "TP560 Data/Fax/Voice 56K Modem".
feb 11 13:23:12.56: [ 5127]: SESSION BEGIN 000004155 34952952105313
feb 11 13:23:12.56: [ 5127]: HylaFAX (tm) Version 4.3.1
feb 11 13:23:12.56: [ 5127]: SEND FAX: JOB 53 DEST 952105313 COMMID 000004155 DEVICE '/dev/ttyS0' FROM 'tecnico ' USER admin
feb 11 13:23:12.56: [ 5127]: <-- [12:AT+FCLASS=1\r]
feb 11 13:23:12.67: [ 5127]: --> [2:OK]
feb 11 13:23:12.68: [ 5127]: DIAL 952105313
feb 11 13:23:12.68: [ 5127]: <-- [14:ATDT952105313\r]
feb 11 13:23:28.83: [ 5127]: --> [7:CONNECT]
feb 11 13:23:30.34: [ 5127]: --> [2:OK]
feb 11 13:23:30.34: [ 5127]: REMOTE NSF "00 00 25 00 00 00 92 10 4D 02 00 58 00 28 88 A0 80 80 B1 60"
feb 11 13:23:30.34: [ 5127]: NSF remote fax equipment: Ricoh
feb 11 13:23:30.34: [ 5127]: <-- [9:AT+FRH=3\r]
feb 11 13:23:30.36: [ 5127]: --> [7:CONNECT]
feb 11 13:23:30.82: [ 5127]: --> [2:OK]
feb 11 13:23:30.83: [ 5127]: REMOTE best rate 33600 bit/s
feb 11 13:23:30.83: [ 5127]: REMOTE max A3 page width (303 mm)
feb 11 13:23:30.83: [ 5127]: REMOTE max unlimited page length
feb 11 13:23:30.83: [ 5127]: REMOTE best vres 200 x 200 dpi
feb 11 13:23:30.83: [ 5127]: REMOTE format support: MH, MR, MMR, JBIG
feb 11 13:23:30.83: [ 5127]: REMOTE supports T.30 Annex A, 256-byte ECM
feb 11 13:23:30.83: [ 5127]: REMOTE best 10 ms/scanline
feb 11 13:23:30.83: [ 5127]: USE 14400 bit/s
feb 11 13:23:30.83: [ 5127]: USE error correction mode
feb 11 13:23:30.83: [ 5127]: SEND file "docq/doc622.ps;c0"
feb 11 13:23:30.83: [ 5127]: USE A4 page width (215 mm)
feb 11 13:23:30.83: [ 5127]: USE unlimited page length
feb 11 13:23:30.83: [ 5127]: USE 3.85 line/mm
feb 11 13:23:30.83: [ 5127]: USE 2-D MMR
feb 11 13:23:30.83: [ 5127]: USE 0 ms/scanline
feb 11 13:23:30.83: [ 5127]: SEND training at v.17 14400 bit/s
feb 11 13:23:30.83: [ 5127]: DELAY 70 ms
feb 11 13:23:30.89: [ 5127]: <-- [9:AT+FTH=3\r]
feb 11 13:23:30.95: [ 5127]: --> [7:CONNECT]
feb 11 13:23:30.95: [ 5127]: <-- data [23]
feb 11 13:23:30.96: [ 5127]: <-- data [2]
feb 11 13:23:30.98: [ 5127]: --> [7:CONNECT]
feb 11 13:23:30.98: [ 5127]: <-- data [7]
feb 11 13:23:30.98: [ 5127]: <-- data [2]
feb 11 13:23:33.16: [ 5127]: --> [2:OK]
feb 11 13:23:33.16: [ 5127]: DELAY 70 ms
feb 11 13:23:33.23: [ 5127]: <-- [11:AT+FTM=145\r]
feb 11 13:23:34.91: [ 5127]: --> [7:CONNECT]
feb 11 13:23:34.92: [ 5127]: <-- data [1024]
feb 11 13:23:34.92: [ 5127]: <-- data [1024]
feb 11 13:23:34.92: [ 5127]: <-- data [652]
feb 11 13:23:34.92: [ 5127]: <-- data [2]
feb 11 13:23:36.46: [ 5127]: --> [2:OK]
feb 11 13:23:36.46: [ 5127]: <-- [9:AT+FRH=3\r]
feb 11 13:23:37.29: [ 5127]: --> [7:CONNECT]
feb 11 13:23:38.31: [ 5127]: --> [2:OK]
feb 11 13:23:38.31: [ 5127]: TRAINING succeeded
feb 11 13:23:38.31: [ 5127]: SEND begin page
feb 11 13:23:38.32: [ 5127]: SEND EOFB
feb 11 13:23:38.32: [ 5127]: SEND send frame number 0
feb 11 13:23:38.32: [ 5127]: SEND send frame number 1
feb 11 13:23:38.32: [ 5127]: SEND send frame number 2
feb 11 13:23:38.32: [ 5127]: SEND send frame number 3
feb 11 13:23:38.32: [ 5127]: DELAY 70 ms
feb 11 13:23:38.38: [ 5127]: <-- [11:AT+FTM=146\r]
feb 11 13:23:38.89: [ 5127]: --> [7:CONNECT]
feb 11 13:23:38.89: [ 5127]: <-- data [1037]
feb 11 13:23:38.89: [ 5127]: <-- data [425]
feb 11 13:23:38.89: [ 5127]: <-- data [2]
feb 11 13:23:39.99: [ 5127]: --> [2:OK]
feb 11 13:23:39.99: [ 5127]: DELAY 90 ms
feb 11 13:23:40.09: [ 5127]: <-- [9:AT+FTH=3\r]
feb 11 13:23:40.14: [ 5127]: --> [7:CONNECT]
feb 11 13:23:40.14: [ 5127]: <-- data [7]
feb 11 13:23:40.14: [ 5127]: <-- data [2]
feb 11 13:23:41.56: [ 5127]: --> [2:OK]
feb 11 13:23:41.56: [ 5127]: SEND send PPS (partial page signal)
feb 11 13:23:41.56: [ 5127]: SEND send EOP (no more pages or documents)
feb 11 13:23:41.56: [ 5127]: <-- [9:AT+FRH=3\r]
feb 11 13:23:41.74: [ 5127]: --> [7:CONNECT]
feb 11 13:23:46.52: [ 5127]: --> [2:OK]
feb 11 13:23:46.52: [ 5127]: HDLC frame too short (0 bytes)
feb 11 13:23:46.52: [ 5127]: DELAY 70 ms
feb 11 13:23:46.58: [ 5127]: <-- [9:AT+FTH=3\r]
feb 11 13:23:46.64: [ 5127]: --> [7:CONNECT]
feb 11 13:23:46.64: [ 5127]: <-- data [3]
feb 11 13:23:46.65: [ 5127]: <-- data [2]
feb 11 13:23:47.95: [ 5127]: --> [2:OK]
feb 11 13:23:47.95: [ 5127]: SEND send CRP (command repeat)
feb 11 13:23:47.95: [ 5127]: <-- [9:AT+FRH=3\r]
feb 11 13:23:48.17: [ 5127]: --> [7:CONNECT]
feb 11 13:23:52.91: [ 5127]: --> [2:OK]
feb 11 13:23:52.91: [ 5127]: HDLC frame too short (0 bytes)
feb 11 13:23:52.91: [ 5127]: DELAY 70 ms
feb 11 13:23:52.98: [ 5127]: <-- [9:AT+FTH=3\r]
feb 11 13:23:53.03: [ 5127]: --> [7:CONNECT]
feb 11 13:23:53.03: [ 5127]: <-- data [3]
feb 11 13:23:53.03: [ 5127]: <-- data [2]
feb 11 13:23:54.35: [ 5127]: --> [2:OK]
feb 11 13:23:54.35: [ 5127]: SEND send CRP (command repeat)
feb 11 13:23:54.35: [ 5127]: <-- [9:AT+FRH=3\r]
feb 11 13:23:57.45: [ 5127]: --> [0:]
feb 11 13:23:57.45: [ 5127]: MODEM <Empty line>
feb 11 13:23:57.45: [ 5127]: <-- data [1]
feb 11 13:23:57.66: [ 5127]: MODEM <Timeout>
feb 11 13:23:57.66: [ 5127]: <-- [9:AT+FTH=3\r]
feb 11 13:23:57.71: [ 5127]: --> [7:CONNECT]
feb 11 13:23:57.72: [ 5127]: <-- data [7]
feb 11 13:23:57.72: [ 5127]: <-- data [2]
feb 11 13:23:59.13: [ 5127]: --> [2:OK]
feb 11 13:23:59.14: [ 5127]: SEND send PPS (partial page signal)
feb 11 13:23:59.14: [ 5127]: SEND send EOP (no more pages or documents)
feb 11 13:23:59.14: [ 5127]: <-- [9:AT+FRH=3\r]
feb 11 13:24:02.23: [ 5127]: --> [0:]
feb 11 13:24:02.23: [ 5127]: MODEM <Empty line>
feb 11 13:24:02.23: [ 5127]: <-- data [1]
feb 11 13:24:02.43: [ 5127]: MODEM <Timeout>
feb 11 13:24:02.43: [ 5127]: <-- [9:AT+FTH=3\r]
feb 11 13:24:02.49: [ 5127]: --> [7:CONNECT]
feb 11 13:24:02.49: [ 5127]: <-- data [7]
feb 11 13:24:02.49: [ 5127]: <-- data [2]
feb 11 13:24:03.90: [ 5127]: --> [2:OK]
feb 11 13:24:03.90: [ 5127]: SEND send PPS (partial page signal)
feb 11 13:24:03.90: [ 5127]: SEND send EOP (no more pages or documents)
feb 11 13:24:03.90: [ 5127]: <-- [9:AT+FRH=3\r]
feb 11 13:24:07.00: [ 5127]: --> [0:]
feb 11 13:24:07.00: [ 5127]: MODEM <Empty line>
feb 11 13:24:07.00: [ 5127]: <-- data [1]
feb 11 13:24:07.20: [ 5127]: MODEM <Timeout>
feb 11 13:24:07.20: [ 5127]: No response to PPS repeated 3 times.
feb 11 13:24:07.20: [ 5127]: SEND end page
feb 11 13:24:07.20: [ 5127]: SEND: No response to PPS repeated 3 times.; Giving up after 3 attempts to send same page "docq/doc622.ps;c0", dirnum 0
feb 11 13:24:07.20: [ 5127]: <-- [9:AT+FTH=3\r]
feb 11 13:24:07.26: [ 5127]: --> [7:CONNECT]
feb 11 13:24:07.26: [ 5127]: <-- data [3]
feb 11 13:24:07.27: [ 5127]: <-- data [2]
feb 11 13:24:08.57: [ 5127]: --> [2:OK]
feb 11 13:24:08.57: [ 5127]: <-- [5:ATH0\r]
feb 11 13:24:09.00: [ 5127]: --> [10:NO CARRIER]
feb 11 13:24:09.00: [ 5127]: MODEM No carrier
feb 11 13:24:09.00: [ 5127]: SESSION END
¿Alguna idea?
Desde ya, gracias por todo.