Discuss September 2006

discuss@lists.centos.org

275 participants
362 discussions

RE: [CentOS] Install Using Floppy/CD
by Paul Malinowski 26 Sep '06

26 Sep '06

Charles, Please share with us, what you would like to do. Describe that well and then expect right answers. Paul -----Original Message----- From: centos-bounces(a)centos.org on behalf of Charles Sliger Sent: Tue 26/09/2006 20:25 To: 'CentOS mailing list' Cc: Subject: [CentOS] Install Using Floppy/CD Is there a doc that describes how to create a floppy that will boot and then switch over to the installation CD? It looks to me like this should be possible using grub on the floppy. Charles L. Sliger, Information Systems Engineer, chaz(a)bctonline.com "No matter where you go, there you are..." This e-mail and all attachments have been scanned by the HighSpeed Office virus scanning service powered by MessageLabs and no known viruses were detected. This e-mail and all attachments have been scanned by the HighSpeed Office virus scanning service powered by MessageLabs and no known viruses were detected.

1 0

RE: [CentOS] Re: Hard drive errors
by Bowie Bailey 26 Sep '06

26 Sep '06

Scott Silva wrote: > Bowie Bailey spake the following on 9/26/2006 8:35 AM: > > Scott Silva wrote: > > > Look for the Ultimate boot disk; > > > http://www.ultimatebootcd.com/ > > > > > > It has many manufacturer hard drive utilities, and you just need > > > to be able to boot from CD. > > > > I burned the CD and tried it out. There are two utilities on the CD > > for Seagate drives, but unless I am missing something, neither of > > them have any diagnostic capability. > > > When you press F2 to get to the disk utilities, you have to use the > left /right arrows to see more menus. I knew I was missing something. Thanks! -- Bowie

2 1

CentOS-announce Digest, Vol 19, Issue 17
by centos-announce-request＠centos.org 26 Sep '06

26 Sep '06

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CESA-2006:0668 Moderate CentOS 3 i386 squirrelmail - security update (Tru Huynh) 2. CESA-2006:0668 Moderate CentOS 3 x86_64 squirrelmail - security update (Tru Huynh) ---------------------------------------------------------------------- Message: 1 Date: Tue, 26 Sep 2006 15:09:45 +0200 From: Tru Huynh <tru(a)centos.org> Subject: [CentOS-announce] CESA-2006:0668 Moderate CentOS 3 i386 squirrelmail - security update To: centos-announce(a)centos.org Message-ID: <20060926130945.GA31250(a)sillage.bis.pasteur.fr> Content-Type: text/plain; charset="us-ascii" CentOS Errata and Security Advisory CESA-2006:0668 squirrelmail security update for CentOS 3 i386: https://rhn.redhat.com/errata/RHSA-2006-0668.html The following updated file has been uploaded and is currently syncing to the mirrors: i386: updates/i386/RPMS/squirrelmail-1.4.8-2.el3.centos.1.noarch.rpm source: updates/SRPMS/squirrelmail-1.4.8-2.el3.centos.1.src.rpm You may update your CentOS-3 i386 installations by running the command: yum update squirrelmail Tru -- Tru Huynh (CentOS-3 i386/x86_64 Package Maintenance) http://pgp.mit.edu:11371/pks/lookup?op=get&search=0xBEFA581B

1 0

RE: [CentOS] Missing dependencies
by Paul Malinowski 26 Sep '06

26 Sep '06

Todd, From my experience I can bet that there is only one or two packages which are source of all problems. a) Try to upgrade yum first. b) try to remove and install again php (copy config files if you have edit them) You can also force upgrade, but that's not recommended (perhaps there is major reason why you have that problems) >> And how do you think it got so out of date? Out of sync? It's hard to say. Keep a track on most importent packages on your system. Paul -----Original Message----- From: centos-bounces(a)centos.org on behalf of Todd Cary Sent: Mon 25/09/2006 19:49 To: CentOS mailing list Cc: Subject: Re: [CentOS] Missing dependencies Paul - There are more than the one I gave as an example. What would you suggest for this list: --> Running transaction check --> Processing Dependency: php = 4.3.9-3.15 for package: php-mysql --> Processing Dependency: php = 4.3.9-3.15 for package: php-mbstring --> Processing Dependency: libgcj = 3.4.5 for package: libgcj-devel --> Processing Dependency: php = 4.3.9-3.15 for package: php-gd --> Processing Dependency: php = 4.3.9-3.15 for package: php-pear --> Processing Dependency: httpd = 2.0.52-22.ent.centos4 for package: httpd-suexec --> Processing Dependency: httpd = 2.0.52-22.ent.centos4 for package: httpd-manual --> Finished Dependency Resolution And how do you think it got so out of date? Out of sync? Todd Paul Malinowski wrote: > There are many ways to fix it, but IMHO the simplest one is to backup config, remove php-mysql, then yum update, and yum install php-mysql. > > It should be fine. > Paul > > > -----Original Message----- > From: centos-bounces(a)centos.org on behalf of Todd Cary > Sent: Mon 25/09/2006 15:05 > To: centos(a)centos.org > Cc: > Subject: [CentOS] Missing dependencies > > I tried to update my Centos with yum update as I have done in the past, > but this time I received a list of dependencies. This is a new > experience for me and I would appreciate any help/suggestions. Here is > one of the lines: > > Error: Missing Dependency: php = 4.3.9-3.15 is needed by package php-mysql > > Todd > > > ------------------------------------------------------------------------ > > _______________________________________________ > CentOS mailing list > CentOS(a)centos.org > http://lists.centos.org/mailman/listinfo/centos > -- Ariste Software 2200 D Street Ext Petaluma, CA 94952 (707) 773-4523 This e-mail and all attachments have been scanned by the HighSpeed Office virus scanning service powered by MessageLabs and no known viruses were detected. This e-mail and all attachments have been scanned by the HighSpeed Office virus scanning service powered by MessageLabs and no known viruses were detected.

2 1

sym53c8xx parity errors
by Rodrigo Barbosa 26 Sep '06

26 Sep '06

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 This seems to be an old problem, but I haven't found much about it. SuSE mentions "hwprobe=-pci" but, as far as I know, CentOS doesn't use it. This does stop the machine from booting (mounting /) quite a few times. Logs: SCSI subsystem initialized sym0: <895> rev 0x2 at pci 0000:00:13.0 irq 177 sym0: Symbios NVRAM, ID 7, Fast-40, LVD, parity checking sym0: open drain IRQ line driver, using on-chip SRAM sym0: using LOAD/STORE-based firmware. sym0: SCSI BUS has been reset. scsi0 : sym-2.1.18j Using cfq io scheduler Vendor: WDIGTL Model: WDE9180 ULTRA2 Rev: 1.30 Type: Direct-Access ANSI SCSI revision: 02 sym0:0:0: tagged command queuing enabled, command queue depth 16. target0:0:0: Beginning Domain Validation sym0:0:0:ODD transfer in DATA IN phase. sym0:0:0:COMMAND FAILED (87 0 10). sym0:0: wide asynchronous. sym0:0:0:ODD transfer in DATA IN phase. sym0:0:0:COMMAND FAILED (87 0 10). sym0:0:0:ODD transfer in DATA IN phase. sym0:0:0:COMMAND FAILED (87 0 10). target0:0:0: Wide Transfers Fail sym0:0: FAST-40 SCSI 40.0 MB/s ST (25.0 ns, offset 31) target0:0:0: Domain Validation skipping write tests target0:0:0: Ending Domain Validation SCSI device sda: 17873040 512-byte hdwr sectors (9151 MB) SCSI device sda: drive cache: write back SCSI device sda: 17873040 512-byte hdwr sectors (9151 MB) SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 Attached scsi disk sda at scsi0, channel 0, id 0, lun 0 Vendor: WDIGTL Model: WDE9180 ULTRA2 Rev: 1.30 Type: Direct-Access ANSI SCSI revision: 02 sym0:1:0: tagged command queuing enabled, command queue depth 16. target0:0:1: Beginning Domain Validation sym0:1:0:ODD transfer in DATA IN phase. sym0:1:0:COMMAND FAILED (87 0 10). sym0:1: wide asynchronous. sym0:1:0:ODD transfer in DATA IN phase. sym0:1:0:COMMAND FAILED (87 0 10). sym0:1:0:ODD transfer in DATA IN phase. sym0:1:0:COMMAND FAILED (87 0 10). target0:0:1: Wide Transfers Fail sym0:1: FAST-40 SCSI 40.0 MB/s ST (25.0 ns, offset 31) target0:0:1: Domain Validation skipping write tests target0:0:1: Ending Domain Validation SCSI device sdb: 17873040 512-byte hdwr sectors (9151 MB) SCSI device sdb: drive cache: write back SCSI device sdb: 17873040 512-byte hdwr sectors (9151 MB) SCSI device sdb: drive cache: write back sdb: sdb1 Attached scsi disk sdb at scsi0, channel 0, id 1, lun 0 kjournald starting. Commit interval 5 seconds (...) sym0: SCSI parity error detected: SCR1=132 DBC=50000000 SBCL=0 sym0:1: ERROR (81:0) (8-0-0) (1f/97/0) @ (scripta 48:aa1001c2). sym0: script cmd = f31c0004 sym0: regdump: da 00 00 97 47 1f 01 0e 00 08 81 00 80 00 0f 0a a8 69 df 1f 02 ff ff ff. sym0: SCSI BUS reset detected. sym0: SCSI BUS has been reset. lcpci: 00:13.0 SCSI storage controller: LSI Logic / Symbios Logic 53c895 (rev 02) Flags: bus master, medium devsel, latency 72, IRQ 177 I/O ports at e800 [size=256] Memory at febeff00 (32-bit, non-prefetchable) [size=256] Memory at febee000 (32-bit, non-prefetchable) [size=4K] 00:13.0 Class 0100: 1000:000c (rev 02) Flags: bus master, medium devsel, latency 72, IRQ 177 I/O ports at e800 [size=256] Memory at febeff00 (32-bit, non-prefetchable) [size=256] Memory at febee000 (32-bit, non-prefetchable) [size=4K] Kernel is still 2.6.9-42.EL. - -- Rodrigo Barbosa "Quid quid Latine dictum sit, altum viditur" "Be excellent to each other ..." - Bill & Ted (Wyld Stallyns) -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.5 (GNU/Linux) iD8DBQFFGVmwpdyWzQ5b5ckRAqLwAJ9ai7u9jn7nDeRm3qPco1Ujt4JoJgCgnuzb HLURpWQMGu0IOFjTxd+3ER8= =w8Fr -----END PGP SIGNATURE-----

1 0

centosplus kernel upgrade
by rado 26 Sep '06

26 Sep '06

the upgrade itself is fine...no problems but I am confused about 1 thing. In order for yum to it's thing w/out updating the kernal, I put this: "exclude=kernel". I put this line in every division of /etc/yum.repos.d. i.e. Base, Updates, Addons, etc. my question is: I don't really know the proper way to exclude. thx John Rose

2 1

RE: [CentOS] Re: Hard drive errors
by Bowie Bailey 26 Sep '06

26 Sep '06

Scott Silva wrote: > Les Mikesell spake the following on 9/25/2006 2:16 PM: > > On Mon, 2006-09-25 at 09:08 -0400, Lamar Owen wrote: > > > > > Power supply issues can do real damage to the drives, as well. I > > > had a pair of 250GB drives that have hard errorred sectors thanks > > > to a power > > > supply 'glitching' on me. The drives still work fine otherwise, > > > but they have several dozen sectors each that will never be > > > usable. > > > > Most drive manufacturers have a diagnostic/repair utility that have > > a fair chance of fixing that sort of problem. Unfortunately they > > tend to only run under windows. > > > Look for the Ultimate boot disk; > http://www.ultimatebootcd.com/ > > It has many manufacturer hard drive utilities, and you just need to > be able to boot from CD. I burned the CD and tried it out. There are two utilities on the CD for Seagate drives, but unless I am missing something, neither of them have any diagnostic capability. -- Bowie

3 2

RE: [CentOS] Re: Hard drive errors
by Bowie Bailey 26 Sep '06

26 Sep '06

chrism(a)imntv.com wrote: > Bowie Bailey wrote: > > I burned the CD and tried it out. There are two utilities on the CD > > for Seagate drives, but unless I am missing something, neither of > > them have any diagnostic capability. > > > > Have you tried here? > > http://www.seagate.com/support/disc/utils.html Not yet, but my comment was directed toward the Ultimate Boot CD. If the CD is designed for doing diagnostics, it seems odd to me that there are two Seagate utilities included, but neither of them is capable of doing diagnostics or testing. (I know this is offtopic, just posting here since someone here suggested using the CD) -- Bowie

1 0

Crontab not working....
by Ian mu 26 Sep '06

26 Sep '06

Hiya all, just found an odd one on one of our boxes, cron isnt working (for a user anyway, but can't seem to get it running properly at all), i.e if I do a crontab -e as a user (who is in /var/spool/cron) and add 19 10 * * * /bin/touch /home/logadmin/testfile (has permission) its never created. Also I get no mails from cron to /var/spool/mail/root so guessing maybe cron not working at all, can't find any errors in logfiles relating to it either. ps -ef shows crond running however, have tried restarting it via service crond restart which shows fine in logs as started Not sure what else to check? Any ideas much appreciated, Ian

4 10

vmware running with socket 939 and AMD
by rado 26 Sep '06

26 Sep '06

Now this is getting exciting! Well, ya,I'm running vmware in 2 boxes. I am hoping this might help someone w/the config that follows: socket 939 mb AMD 3200+ clawhammer 1. do: # uname -r returns: 2.6.9-42.0.2.EL (CentOS 4.4 stock kernel) 2. edit /boot/grub/grub.conf: make the vmlinuz line look like: kernel /vmlinuz-2.6.9-42.0.2.EL ro root=/dev/VolGroup00/LogVol00 rhgb clock=pit quiet "clock=pit" is added. those are the only tweaks I did to produce a stable clock and get rid of that repeating kb problem. I made these tweaks 2 days ago (Sun). Monitoring it yesterday I never seen the time off more than 1 minute. but I didn't do any thing on that box yesterday. This morning I just changed the user back to rado and testing the key repeat issue right now. thx Les and Aleksandar for y'alls suggestions. John Rose

1 0

← Newer
1
...
5
6
7
8
9
10
11
...
37
Older →

Jump to page:

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss September 2006