Discuss March 2014

discuss@lists.centos.org

167 participants
144 discussions

Dell vostro 1550, BCM 4313 wireless, not connecting to net
by Giri Prasad 13 Mar '14

13 Mar '14

Hello All, I have a Dell Vostro 1550 laptop. i3 core, 64 bit, 8gb ram etc etc. I had a nic interface, but some how the wired nic is not working. So I am trying to use the BCM 4313 wireless chip, of this system, to connect to the internet. I have Cent os 6.5 (64 bit) installed with the required libraries and kernel sources, headers etc. I got the source code of the driver, hybrid-v35_64-nodebug-pcoem-6_30_223_141.tar.gz. Extracted the tar, and compiled. Normal compilation errors: # make ## Errors # make API=CFG80211 ## Errors # make API=WEXT ---------> Compiles fine. # rmmod bcma echo "blacklist bcma" >> /etc/modprobe.d/blacklist.conf # modprobe lib80211 # modprobe cfg80211 # insmod wl.ko Network Manager shows all surrounding wireless network, and I select my wifi network and enter the key. Authentication required by wireless network (Dialog Box) Passwords or encryption keys are required to access the wireless network 'giri' Wireless security : WEP 40/128-bit key (HEX or ASCII) Key : ********************* When I hit the <Connect> button of this dialog box, the network manager shows the rotating signal in the network connection at the top of the Linux desktop status bar. But after a few seconds, once again this dialog-box "Authentication required by wireless network" pops up, and keeps asking me for the key/password. Rhel 6 (64 bit), I built the same driver, and make (only just make - without parameters) for compiling the driver, created the driver, without any problems. Insmod the driver, and upon selecting the wifi network and entering the key, rhel 6 64 bit version, perfectly connected to the net, on this same laptop. Can anyone let me know, why the centos 6.5 kernel/Network Manager is asking for the (wireless security) key every few seconds, again and again, and not connecting to the internet. Thanks in advance. Regards, Giri [root@localhost hybrid_wl]# [root@localhost hybrid_wl]# lspci | grep -i Broad 09:00.0 Network controller: Broadcom Corporation BCM4313 802.11bgn Wireless Network Adapter (rev 01) [root@localhost hybrid_wl]# make /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:726: error: ‘struct cfg80211_ibss_params’ has no member named ‘channel’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1092: error: parameter 2 (‘type’) has incomplete type /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1103: error: ‘TX_POWER_AUTOMATIC’ undeclared (first use in this function) /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1103: error: (Each undeclared identifier is reported only once /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1103: error: for each function it appears in.) /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1105: error: ‘TX_POWER_LIMITED’ undeclared (first use in this function) /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1111: error: ‘TX_POWER_FIXED’ undeclared (first use in this function) /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c: At top level: /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1589: warning: initialization from incompatible pointer type /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1594: warning: initialization from incompatible pointer type /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1595: warning: initialization from incompatible pointer type /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1596: warning: initialization from incompatible pointer type /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1597: warning: initialization from incompatible pointer type /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1598: warning: initialization from incompatible pointer type /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1599: warning: initialization from incompatible pointer type /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_inform_single_bss’: /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1764: error: too few arguments to function ‘ieee80211_channel_to_frequency’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1793: warning: passing argument 1 of ‘cfg80211_put_bss’ from incompatible pointer type include/net/cfg80211.h:3380: note: expected ‘struct wiphy *’ but argument is of type ‘struct cfg80211_bss *’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:1793: error: too few arguments to function ‘cfg80211_put_bss’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_update_bss_info’: /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2046: error: ‘struct cfg80211_bss’ has no member named ‘information_elements’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2047: error: ‘struct cfg80211_bss’ has no member named ‘len_information_elements’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2052: warning: passing argument 1 of ‘cfg80211_put_bss’ from incompatible pointer type include/net/cfg80211.h:3380: note: expected ‘struct wiphy *’ but argument is of type ‘struct cfg80211_bss *’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2052: error: too few arguments to function ‘cfg80211_put_bss’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_bss_roaming_done’: /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2090: warning: passing argument 2 of ‘cfg80211_roamed’ from incompatible pointer type include/net/cfg80211.h:3726: note: expected ‘struct ieee80211_channel *’ but argument is of type ‘u8 *’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2090: warning: passing argument 4 of ‘cfg80211_roamed’ makes pointer from integer without a cast include/net/cfg80211.h:3726: note: expected ‘const u8 *’ but argument is of type ‘s32’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2090: warning: passing argument 5 of ‘cfg80211_roamed’ makes integer from pointer without a cast include/net/cfg80211.h:3726: note: expected ‘size_t’ but argument is of type ‘u8 *’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2090: warning: passing argument 6 of ‘cfg80211_roamed’ makes pointer from integer without a cast include/net/cfg80211.h:3726: note: expected ‘const u8 *’ but argument is of type ‘s32’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2090: error: too few arguments to function ‘cfg80211_roamed’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c: In function ‘wl_bss_connect_done’: /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2122: warning: passing argument 2 of ‘cfg80211_roamed’ from incompatible pointer type include/net/cfg80211.h:3726: note: expected ‘struct ieee80211_channel *’ but argument is of type ‘u8 *’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2122: warning: passing argument 4 of ‘cfg80211_roamed’ makes pointer from integer without a cast include/net/cfg80211.h:3726: note: expected ‘const u8 *’ but argument is of type ‘s32’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2122: warning: passing argument 5 of ‘cfg80211_roamed’ makes integer from pointer without a cast include/net/cfg80211.h:3726: note: expected ‘size_t’ but argument is of type ‘u8 *’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2122: warning: passing argument 6 of ‘cfg80211_roamed’ makes pointer from integer without a cast include/net/cfg80211.h:3726: note: expected ‘const u8 *’ but argument is of type ‘s32’ /root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.c:2122: error: too few arguments to function ‘cfg80211_roamed’ make[2]: *** [/root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl/src/wl/sys/wl_cfg80211_hybrid.o] Error 1 make[1]: *** [_module_/root/Desktop/linux-wireless1/linux-wireless/bcm-4313/hybrid_wl] Error 2 make[1]: Leaving directory `/usr/src/kernels/2.6.32-431.el6.x86_64' make: *** [all] Error 2 [root@localhost hybrid_wl]# dmesg | tail -20 wl 0000:09:00.0: setting latency timer to 64 lib80211_crypt: registered algorithm 'TKIP' eth0: Broadcom BCM4727 802.11 Hybrid Wireless Controller 6.30.223.141 (r415941) wl 0000:09:00.0: PCI INT A disabled lib80211_crypt: unregistered algorithm 'TKIP' lib80211_crypt: unregistered algorithm 'NULL' lib80211: common routines for IEEE802.11 drivers lib80211_crypt: registered algorithm 'NULL' cfg80211: Calling CRDA to update world regulatory domain cfg80211: World regulatory domain updated: cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) wl 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 wl 0000:09:00.0: setting latency timer to 64 lib80211_crypt: registered algorithm 'TKIP' eth0: Broadcom BCM4727 802.11 Hybrid Wireless Controller 6.30.223.141 (r415941) [root@localhost hybrid_wl]# lsmod Module Size Used by lib80211_crypt_tkip 9470 0 wl 4176734 0 cfg80211 619515 0 lib80211 5127 2 lib80211_crypt_tkip,wl vfat 10584 1 [root@localhost hybrid_wl]# iwconfig lo no wireless extensions. p1p1 no wireless extensions. pan0 no wireless extensions. eth0 IEEE 802.11 ESSID:"" Nickname:"" Mode:Managed Frequency:2.462 GHz Access Point: Not-Associated Bit Rate:72 Mb/s Tx-Power:24 dBm Retry min limit:7 RTS thr:off Fragment thr:off Encryption key:off Power Managementmode:All packets received Link Quality=5/5 Signal level=0 dBm Noise level=-94 dBm Rx invalid nwid:0 Rx invalid crypt:0 Rx invalid frag:0 Tx excessive retries:0 Invalid misc:0 Missed beacon:0 [root@localhost hybrid_wl]# dmesg | tail -20 wl 0000:09:00.0: setting latency timer to 64 lib80211_crypt: registered algorithm 'TKIP' eth0: Broadcom BCM4727 802.11 Hybrid Wireless Controller 6.30.223.141 (r415941) wl 0000:09:00.0: PCI INT A disabled lib80211_crypt: unregistered algorithm 'TKIP' lib80211_crypt: unregistered algorithm 'NULL' lib80211: common routines for IEEE802.11 drivers lib80211_crypt: registered algorithm 'NULL' cfg80211: Calling CRDA to update world regulatory domain cfg80211: World regulatory domain updated: cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) wl 0000:09:00.0: PCI INT A -> GSI 19 (level, low) -> IRQ 19 wl 0000:09:00.0: setting latency timer to 64 lib80211_crypt: registered algorithm 'TKIP' eth0: Broadcom BCM4727 802.11 Hybrid Wireless Controller 6.30.223.141 (r415941)

1 0

Seeking Speakers for Upcoming Dojos
by Joe Brockmeier 13 Mar '14

13 Mar '14

Hi all, If you follow the centos-promo mailing list (it exists!)[1] you may have noticed a lot of discussion lately around putting together a lot of CentOS Dojos this year. We're currently planning, and have announced, several Dojos: * March 31 (Santa Clara, CA): http://wiki.centos.org/Events/Dojo/SantaClara2014 * April 10 (Denver, CO): http://wiki.centos.org/Events/Dojo/Denver2014 * April 11 (Lyon, France): http://wiki.centos.org/Events/Dojo/Lyon2014 And we have quite a few more. If you are using CentOS in production, doing interesting things on CentOS, or have ideas for presentations that would be very interesting for CentOS users, please feel free to get in touch with me or KB about speaking at one of the Dojos. We're very much looking for presentations or discussions that will be relevant to folks who are using CentOS at scale. Case studies, best practices, tips and tricks, etc. What we avoid at Dojos are product pitches or 101-type presentations that won't be useful for experienced admins / users. Please let me know if you have any questions. Thanks! [1] http://lists.centos.org/mailman/listinfo/centos-promo -- Joe Brockmeier jzb(a)zonker.net Twitter: @jzb http://www.dissociatedpress.net/

1 0

OT: missing /dev paths
by James Pifer 13 Mar '14

13 Mar '14

Looking for help kind of in a hurry. I've been searching google but not finding any options. Is there any way to fix missing /dev paths to luns without rebooting? For example, see the output from lsscsi below. The only way I know to fix this is with a reboot, but I REALLY Need to avoid that if possible. Thanks James [2:0:1:150] disk DataCore Virtual Disk DCS - [2:0:1:151] disk DataCore Virtual Disk DCS - [2:0:1:152] disk DataCore Virtual Disk DCS - [2:0:1:153] disk DataCore Virtual Disk DCS - [2:0:1:154] disk DataCore Virtual Disk DCS /dev/sdic [2:0:1:155] disk DataCore Virtual Disk DCS - [2:0:1:156] disk DataCore Virtual Disk DCS - [2:0:1:157] disk DataCore Virtual Disk DCS - [2:0:1:158] disk DataCore Virtual Disk DCS - [2:0:1:159] disk DataCore Virtual Disk DCS /dev/sdid [2:0:1:160] disk DataCore Virtual Disk DCS /dev/sdie [2:0:1:161] disk DataCore Virtual Disk DCS - [2:0:1:162] disk DataCore Virtual Disk DCS - [2:0:1:163] disk DataCore Virtual Disk DCS - [2:0:1:164] disk DataCore Virtual Disk DCS - [2:0:1:165] disk DataCore Virtual Disk DCS /dev/sdif [2:0:1:166] disk DataCore Virtual Disk DCS /dev/sdig [2:0:1:167] disk DataCore Virtual Disk DCS /dev/sdih [2:0:1:168] disk DataCore Virtual Disk DCS /dev/sdii [2:0:1:169] disk DataCore Virtual Disk DCS /dev/sdij

3 5

CentOS 5.x and HP ACU CLI
by John R Pierce 12 Mar '14

12 Mar '14

I had to install C5 on a dev server for various reasons (legacy system support and so forth). This dev server is a HP DL180 G6, with a SmartArray P410 raid card... I've installed hpacucli via the RPM from HP's site, but its not finding the controller... C5 (64 bit) is using the default CCISS drivers for this card. # hpacucli ctrl all show config Error: No controllers detected. lspci -v reports... 06:00.0 RAID bus controller: Hewlett-Packard Company Smart Array G6 controllers (rev 01) Subsystem: Hewlett-Packard Company Smart Array P410 Flags: bus master, fast devsel, latency 0, IRQ 66 Memory at fbc00000 (64-bit, non-prefetchable) [size=2M] Memory at fbbff000 (64-bit, non-prefetchable) [size=4K] I/O ports at d800 [size=256] Expansion ROM at fbb00000 [disabled] [size=512K] Capabilities: [40] Power Management version 3 Capabilities: [50] MSI: Enable- Count=1/1 Maskable- 64bit+ Capabilities: [70] Express Endpoint, MSI 00 Capabilities: [ac] MSI-X: Enable+ Count=16 Masked- Capabilities: [100] Advanced Error Reporting Kernel driver in use: cciss Kernel modules: cciss -- john r pierce 37N 122W somewhere on the middle of the left coast

2 4

CentOS-announce Digest, Vol 109, Issue 5
by centos-announce-request＠centos.org 12 Mar '14

12 Mar '14

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CEBA-2014:0281 CentOS 6 ksh Update (Johnny Hughes) 2. CEBA-2014:0282 CentOS 5 cman Update (Johnny Hughes) ---------------------------------------------------------------------- Message: 1 Date: Tue, 11 Mar 2014 14:16:26 +0000 From: Johnny Hughes <johnny(a)centos.org> Subject: [CentOS-announce] CEBA-2014:0281 CentOS 6 ksh Update To: centos-announce(a)centos.org Message-ID: <20140311141626.GA47772(a)n04.lon1.karan.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Bugfix Advisory 2014:0281 Upstream details at : https://rhn.redhat.com/errata/RHBA-2014-0281.html The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) i386: 8b07c3a67e834eb488b902ec77ecdc93c03307d36dd842a6b06eaf20abdfe9ad ksh-20120801-10.el6_5.4.i686.rpm x86_64: a903b3de866f36988c9b990890d748b221e424a454529d51fe69bb51de8aba36 ksh-20120801-10.el6_5.4.x86_64.rpm Source: 6ec92478cecc44e533b42137aecfbaf2998fbcd8a4724a623e87ca97e1bafd64 ksh-20120801-10.el6_5.4.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net ------------------------------ Message: 2 Date: Tue, 11 Mar 2014 16:59:24 +0000 From: Johnny Hughes <johnny(a)centos.org> Subject: [CentOS-announce] CEBA-2014:0282 CentOS 5 cman Update To: centos-announce(a)centos.org Message-ID: <20140311165924.GA11497(a)chakra.karan.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Bugfix Advisory 2014:0282 Upstream details at : https://rhn.redhat.com/errata/RHBA-2014-0282.html The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) i386: 6b85ee4969be5a12c0b67656f15672aaf0f4132e4667a326697856cac270aa84 cman-2.0.115-118.el5_10.4.i386.rpm 6aa49110aafcbd62a15a10e1bc768fec76adc4a27d9a87e84dd08c7be2446304 cman-devel-2.0.115-118.el5_10.4.i386.rpm x86_64: 686bd324ee9bcb82b2ecdd9b961751e5c4edad983506185b81b6b57cd50e451a cman-2.0.115-118.el5_10.4.x86_64.rpm 6aa49110aafcbd62a15a10e1bc768fec76adc4a27d9a87e84dd08c7be2446304 cman-devel-2.0.115-118.el5_10.4.i386.rpm 3587fa2a83907928143cb31146e381bcc4a859a3d4315b05ddda9eb561323706 cman-devel-2.0.115-118.el5_10.4.x86_64.rpm Source: 78ef1052ecab5c2f0939cd541c73d670862ca33eb262624d8b97588ba68302b1 cman-2.0.115-118.el5_10.4.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net ------------------------------ _______________________________________________ CentOS-announce mailing list CentOS-announce(a)centos.org http://lists.centos.org/mailman/listinfo/centos-announce End of CentOS-announce Digest, Vol 109, Issue 5 ***********************************************

1 0

Re: [CentOS] radius?
by James B. Byrne 12 Mar '14

12 Mar '14

On Tue, March 11, 2014 07:46, Hadi Motamedi wrote: > Dear All > Can you please let me know how can I check if a radius server > application is present on my centos server ? > Thank you > > yum list \*radius\* . . . Installed Packages radiusclient-ng.x86_64 0.5.6-5.el6 @anaconda-CentOS-201207061011.x86_64/6.3 radiusclient-ng-devel.x86_64 0.5.6-5.el6 @anaconda-CentOS-201207061011.x86_64/6.3 Available Packages freeradius.x86_64 2.1.12-4.el6_3 base freeradius-krb5.x86_64 2.1.12-4.el6_3 base freeradius-ldap.x86_64 2.1.12-4.el6_3 base freeradius-mysql.x86_64 2.1.12-4.el6_3 base freeradius-perl.x86_64 2.1.12-4.el6_3 base freeradius-postgresql.x86_64 2.1.12-4.el6_3 base freeradius-python.x86_64 2.1.12-4.el6_3 base freeradius-unixODBC.x86_64 2.1.12-4.el6_3 base freeradius-utils.x86_64 2.1.12-4.el6_3 base yum list installed \*radius\* . . . Installed Packages radiusclient-ng.x86_64 0.5.6-5.el6 @anaconda-CentOS-201207061011.x86_64/6.3 radiusclient-ng-devel.x86_64 0.5.6-5.el6 @anaconda-CentOS-201207061011.x86_64/6.3 -- *** E-Mail is NOT a SECURE channel *** James B. Byrne mailto:ByrneJB@Harte-Lyne.ca Harte & Lyne Limited http://www.harte-lyne.ca 9 Brockley Drive vox: +1 905 561 1241 Hamilton, Ontario fax: +1 905 561 0757 Canada L8E 3C3

2 1

Re: [CentOS] ISO mag card encoding and writing
by James B. Byrne 11 Mar '14

11 Mar '14

On Mon, March 10, 2014 15:56, Always Learning wrote: > > On Mon, 2014-03-10 at 14:16 -0400, James B. Byrne wrote: > >> We have a potential requirement to produce a limited number of embossed PVC >> cards with magnetic encoding for an internal project. > > Why not consider either keyfobs or credit-card size cards with embedded > RFID tags ? Each RFID has a unique ID. > The cards have to interface with an existing system provided by an outside agency that is based on magnetic swipe technology. The potential project is internal but the environment is not. -- *** E-Mail is NOT a SECURE channel *** James B. Byrne mailto:ByrneJB@Harte-Lyne.ca Harte & Lyne Limited http://www.harte-lyne.ca 9 Brockley Drive vox: +1 905 561 1241 Hamilton, Ontario fax: +1 905 561 0757 Canada L8E 3C3

1 0

radius?
by Hadi Motamedi 11 Mar '14

11 Mar '14

Dear All Can you please let me know how can I check if a radius server application is present on my centos server ? Thank you

3 2

Samba on Centos 5/6 differences
by Steve Campbell 11 Mar '14

11 Mar '14

Kinda OT. I've been trying to get Samba running on a Centos 5 box for some time now, but can't seem to get it to happen. I can not connect to the machine from our external network but I can connect from a box on the same network. So it seems like a firewall problem. Funny thing is I have no problem with Samba on a Centos 6 box. For now, that's the one I'm using for all of my mounts. I have looked and looked at my firewall to try and find a difference in the "allows", but can find nothing, so I ask... Does anyone have a clue as to whether there was a difference in the setup for Samba on Centos 5 from the setup on Centos 6 that might be a 'gotcha'? Sorry for the stupidity. I've checked all the ports needed, both TCP and UDP, and they all seem to be open. I'm hoping there was a change in defaults or something I'm just overlooking. Thanks steve campbell

3 3

CentOS-announce Digest, Vol 109, Issue 4
by centos-announce-request＠centos.org 11 Mar '14

11 Mar '14

1 0

← Newer
1
...
8
9
10
11
12
13
14
15
Older →

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss March 2014