May 2020 - Discuss - lists.centos.org

Issues booting centos7 [dracut is failing to enable centos/root, centos/swap LVs]
by Yannis Milios 01 Feb '25

01 Feb '25

Hello, I'm having a strange problem booting a new centos7 installation. Below some background on this. [I have attached the tech details at the bottom of this message] I started a new CentOS7 installation on a VM, so far all good, o/s boots fine. Then I decided to increase VM disk size (initially was 10G) to 13G. Powered off the VM, increased the vhd via the hypervisor, booted from CentOS livecd, selected "recover my centos installation". Then I used the following sequence of commands to make the new vhd size "visible" to the o/s ... - ran fdisk /dev/sda and deleted partition 2. (This is the LVM partition where the o/s is stored. The first partition is /boot [xfs] partition *non lvm*.) - created a new partition with same starting sector as before deleting it, but a different ending sector (to reflect to the increased space). - set partition type to 8e (lvm), saved settings and exit. - ran pvresize and lvresize to make new space visible to the o/s.All good, I can see the space increase on 'lvdisplay centos/root'. - ran 'mount /dev/mapper/centos-root /mnt/root' to temporarily mount the o/s partition. - ran 'xfs_growfs /mnt/root' to resize the o/s fs to the new size. It was successful and I could actually chroot to the o/s and verify new disk size. - rebooted and tried to boot from hdd this time. Grub menu shows up and loads default kernel (3.10.0-862.9.1.el7.x86_64). - after initial kernel boot up process, booting continues to initrd and then it's where the problem starts... - looks like dracut has issues locating/enabling /dev/mapper/centos-root (lv) and as a result it cannot boot to the 'real' root fs (/). - while in dracut shell, I execute the following command sequence: 1. lvm lvchange -ay /dev/centos/root 2. lvm lvchange -ay /dev/centos/swap 3. ln -s /dev/mapper/centos-root /dev/root 4. exit ...and the o/s boots fine...so looks like the pv,vg,lv is detected properly while in initrd, but somehow dracut has difficulties enabling the root,swap LVs ? - While in o/s, I rebuild initrd by using: 'dracut -f -v -a lvm' Note, I have to use '-a lvm' as for some reason, if don't, the lvm utils (lvm,lvm_scan) are not being included to the initrd, not sure why this happens. After rebooting, same thing happens, I have to manually boot the system via dracut shell. I'm a bit stuck at this point, any clues what I'm doing wrong in here ? As I previously said, this is a new installation, so I could simply reinstall the whole thing, but I would rather try to find out some answer to why is this happening ... :-) [curiosity] Some additional details: ================== I've attached /run/initramfs/rdsosreport.txt file [generated while in inird] here: https://privatebin.net/?fdc4052c0c402884#gdB/QYR3IeR55SxUbjfrkZPQfJ7jMxiUxq… o/s ver=CentOS Linux release 7.5.1804 (Core) [root@localhost ~]# lsblk NAME MAJ:MIN RM SIZE RO TYPE MOUNTPOINT sda 8:0 0 13G 0 disk ├─sda1 8:1 0 500M 0 part /boot └─sda2 8:2 0 12.5G 0 part ├─centos-root 253:0 0 11.5G 0 lvm / └─centos-swap 253:1 0 1G 0 lvm [SWAP] [root@localhost ~]# cat /etc/default/grub GRUB_TIMEOUT=5 GRUB_DISTRIBUTOR="$(sed 's, release .*$,,g' /etc/system-release)" GRUB_DEFAULT=saved GRUB_DISABLE_SUBMENU=true GRUB_TERMINAL_OUTPUT="console" GRUB_CMDLINE_LINUX="rd.lvm.lv=centos/root rd.lvm.lv=centos/swap rd.shell rhgb" GRUB_DISABLE_RECOVERY="true"

4 11

MATE 1.20 test build for CentOS 7 available
by Greg Bailey 14 Oct '21

14 Oct '21

Hi everyone, There's been discussions in the past about updating MATE RPMs in EPEL-7: https://bugzilla.redhat.com/show_bug.cgi?id=1436260 https://lists.centos.org/pipermail/centos/2019-August/173154.html (and lots of others...) As a proof-of-concept, I've written some scripts that clone specific commits from the Fedora master branches, and then runs a tool to re-apply RPM scriptlets that are required by EL7 but removed from the Fedora .spec files. The scripts are available at: https://github.com/gebailey/mate-rpms/tree/master/1.20/el7 There's also instructions there if you want to try upgrading to MATE 1.20 w/o rebuilding them yourself. If these packages work for others, perhaps we can revisit the idea of updating the epel7 branches of the Fedora git repos and submitting an official update. There's nothing here (yet) about building MATE 1.22 (which might require a newer gcc for EL7), or building anything on CentOS 8, but thought the CentOS 7 users might find this helpful. -Greg

6 17

LibreOffice locking up
by H 07 Nov '20

07 Nov '20

I am running LibreOffice 5.3.6.1 under the latest update of CentOS 7 and the Mate desktop. Not infrequently LibreOffice Calc locks up and I have to force close the application. Altough the spreadsheet is rather large I would not consider it complex. This has been going on for some time and I am curious if the bug might be in LibreOffice or if there is some interaction with the Mate desktop that might be responsible. Both CentOS, LibreOffice and Mate have been regularly updated from the standard repositories for a long time. Does anyone else have the same problem?

6 11

CentOS7 and NFS
by Patrick Bégou 28 Aug '20

28 Aug '20

Hi, I need some help with NFSv4 setup/tuning. I have a dedicated nfs server (2 x E5-2620 8cores/16 threads each, 64GB RAM, 1x10Gb ethernet and 16x 8TB HDD) used by two servers and a small cluster (400 cores). All the servers are running CentOS 7, the cluster is running CentOS6. Time to time on the server I get: kernel: NFSD: client xxx.xxx.xxx.xxx testing state ID with incorrect client ID And the client xxx.xxx.xxx.xxx freeze whith: kernel: nfs: server xxxxx.legi.grenoble-inp.fr not responding, still trying kernel: nfs: server xxxxx.legi.grenoble-inp.fr OK kernel: nfs: server xxxxx.legi.grenoble-inp.fr not responding, still trying kernel: nfs: server xxxxx.legi.grenoble-inp.fr OK There is a discussion on RedHat7 support about this but only open to subscribers. Other searches with google do not provide useful information. Do you have an idea how to solve these freeze states ? More generally I would be really interested with some advice/tutorials to improve NFS performances in this dedicated context. There are so many [different] things about tuning NFS available on the web that I'm a little bit lost (the opposite of the previous question). So if some one has "the tutorial"...;-) Thanks Patrick

7 14

Brother HL-L2360DW printing quality
by H 23 Jul '20

23 Jul '20

I have the above printer but have not been able to resolve issues with the printing quality in CentOS 7. The test page prints fine but when I print PDF-documents, most recently using Chinese fonts, it is lacking and the pages very hard to read. The settings in the Mate Cups configuration panel are fine and set to 600 dpi, the settings in the printer menu are all OK yet it prints more like maybe 150 or even 75 dpi. Any suggestion what might be wrong?

3 7

Where can I find centos-release-8.1-1.1911.0.9.el8.src.rpm
by me＠tdiehl.org 01 Jun '20

01 Jun '20

Hi, I am looking for centos-release-8.1-1.1911.0.9.el8.src.rpm. Does anyone know where to find it. The only thing I see in vault is centos-release-8.1-1.1911.0.8.el8.src.rpm. Regards, -- Tom me(a)tdiehl.org

3 2

docker-firewalld
by Thomas Stephen Lee 31 May '20

31 May '20

Hi, https://fedoraproject.org/wiki/Changes/firewalld_default_to_nftables mentions a docker-firewalld where can I find that package or source code? thanks --- Lee

3 5

looking for ideas about how to create a constant data stream
by hw＠gc-24.de 30 May '20

30 May '20

Hi, I'm looking for a good way to create a constant data stream that will occupy a bandwidth of about 2--5Mbit/sec between two remote hosts over the internet. I have full access to the hosts involved. My first attempt to use scp to copy data from /dev/null on host A to /dev/null on host B, but scp says '/dev/null: not a regular file'. If something like that would work, I would be able to limit the bandwidth of this transfer in the router(s) involved so that it won't occupy all the bandwidth. Of course, it would be better if I could limit the bandwidth on the sending side rather than dropping packages. I could probably write some program to do that, but since I have never programmed such a kind of network application, it would be rather time consuming. Maybe there's already a kind of tool around that can do this. I need this to work around whatever settings my ISP has made 3 days ago that block my VPN connection so that I effectively can't reasonably work anymore. I do know what the problem with the connection is and that occupying some bandwidth would unblock the VPN; only there doesn't seem to be anything else I could about it.

6 5

Re: [CentOS] Recover from an fsck failure
by James B. Byrne 29 May '20

29 May '20

On Thu, May 28, 2020 19:38, Robert Nichols wrote: > What output do you get from: > > file -s /dev/mapper/vg_voinet01-lv_log > lsblk -f /dev/mapper/vg_voinet01-lv_log > file -s /dev/mapper/vg_voinet01-lv_log /dev/mapper/vg_voinet01-lv_log: symbolic link TO '../DM-5' dm-f lsblk -f /dev/mapper/vg_voinet01-lv_log NAME FSTYPE LABEL UUID MOUNTPOINT vg_voinet01-lv_log (dm-5) The cloned source is a CentOS-6.6 based FreePBSX appliance using lvm. It has a single 500GB HDD. The source host is running and testing of its HDD shows no errors from the test. However, the number of recoverable read and write errors are abnormally high indicating that the HDD is approaching the end of its service life. I wish to replace it without having to rebuild the entire PBX system from scratch. All of the LVMs on the cloned HDD are ext4 file systems. The only one that failed is the log partition /var/log. If I cannot fix this then I wish to replace it with an empty fs and simply rsync the contents of /var/log from the running system to it. I need to do this anyway just prior to replacement as the PBX is running. However, it is about six years since I last had to do this and while I have my notes I would appreciate a short precis of the steps involved. This is the file system layout. /etc/fstab /dev/mapper/vg_voinet01-lv_root / ext4 defaults 1 1 UUID=302ab0fo-f985-4903-86e2-e218b1345e0 /boot ext4 defaults 1 2 /dev/mapper/vg_voinet01-lv_home /home ext4 defaults 1 2 /dev/mapper/vg_voinet01-LogVol04 /var ext4 defaults 1 2 /dev/mapper/vg_voinet01-lv_log /var/log ext4 defaults 1 2 /dev/mapper/vg_voinet01-lv_spool /var/spool ext4 defaults 1 2 /dev/mapper/vg_voinet01-lv_swap swap swap defaults 0 0 tmpfs /dev/shm tmpfs defaults,nodev,. . . parted -l Model: ATA WDC WD1002FAEX-0 (scsi) Disk /dev/sda: 1000GB Sector size (logical/physical): 512B/512B Partition Table: msdos Number Start End Size Type File system Flags 1 1094kB 525MB 524MB primary ext4 boot 2 525MB 500GB 500GB primary lvm Model: Linux device-maper (linear) (dm) Disk: /dev/mapper/vg_voinet01-lv_spool: 68.7GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size Type File system Flags 1 0.00B 68.7GB 68.7GB primary ext4 Error: /dev/mapper/vg_voinet01-lv_log: unrecognized disk label Model: Linux device-maper (linear) (dm) Disk: /dev/mapper/vg_voinet01-lv_home: 3355MB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size Type File system Flags 1 0.00B 3355MB 3355MB primary ext4 Model: Linux device-maper (linear) (dm) Disk: /dev/mapper/vg_voinet01-LogVol04: 336GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size Type File system Flags 1 0.00B 336GB 336GB primary ext4 Error: /dev/mapper/vg_voinet01-lv_swap: unrecognized disk label Model: Linux device-maper (linear) (dm) Disk: /dev/mapper/vg_voinet01-lv_spool: 67.1GB Sector size (logical/physical): 512B/512B Partition Table: loop Number Start End Size Type File system Flags 1 0.00B 67.1GB 67.1GB primary ext4 I will have to do this from a live cd I presume as the shell that the failed boot process dropped me into give a "File-based locking initialisation failed." when I try to run vgdisplay or vgs. Any guidance appreciated. -- *** e-Mail is NOT a SECURE channel *** Do NOT transmit sensitive data via e-Mail Do NOT open attachments nor follow links sent by e-Mail James B. Byrne mailto:ByrneJB@Harte-Lyne.ca Harte & Lyne Limited http://www.harte-lyne.ca 9 Brockley Drive vox: +1 905 561 1241 Hamilton, Ontario fax: +1 905 561 0757 Canada L8E 3C3

2 2

Re: [CentOS] network disconnection after several hours
by Thomas Poty 29 May '20

29 May '20

I will check with firewall-cmd. Regarding hardware problem I have doubt as we use VMWare (but I keep in a corner of my mind).At this moment, we have compiled kernel and have installed it and have tried 4 restore passed.We need to do more tests and understand why 4 restores passed. Thanks Thomas Poty Le jeudi 28 mai 2020 à 23:58:22 UTC+2, hw <hw(a)adminart.net> a écrit : On Tuesday, May 26, 2020 2:42:13 PM CEST Thomas Poty via CentOS wrote: > Hi,We have tried : > - with and without NetworkManager-config-server- with and without > NetworkManagerbut result is still the same : we get disconnection :-/ We > will try with the last kernel. > anybody has a track to explore ? > Thanks > Have you enabled logging with firewall-cmd to see if there are packets being dropped while the dump is being restored? Besides that, one of the first things I'd try is changing out the network card, replace the network cable and use a different port on the switch. Keep in mind that two machines are involved. Even stupid network cables can "switch" between working and non-working for no reason at all like you wouldn't believe ... until you plug them into a PoE switch by mistake after which they suddenly no longer work at all.

1 0

Recover from an fsck failure
by James B. Byrne 28 May '20

28 May '20

This is CentOS-6x. I have cloned the HDD of a CentOS-6 system. I booted a host with that drive and received the following error: checking filesystems /dev/mapper/vg_voinet01-lv_root: clean, 128491/4096000 files, 1554114/16304000 blocks /dev/sda1: clean, 47/120016 files, 80115/512000 blocks /dev/mapper/vg_voinet01-lv_home: clean, 7429/204800 files, 90039/819200 blocks /dev/mapper/vg_voinet01-LogVol04: clean, 770219/20480000 files, 34881086/8102000 blocks fsck.ext4: Bad magic number in super-block while trying to open /dev/mapper/vg_voinet01-lv_log /dev/mapper/vg_voinet01-lv_log The superblock could not be read or does not describe a correct ext2 filesystem. If the device is valid and it really contains an ext2 filesystem (and not swap or ufs or something else), then the superblock is corrupt, and you might try running e2fsck with an alternate superblock: e2fsk -b 8193 <device> /dev/mapper/vg_voinet-lv_spool: clean, 372/614400 files, 171186/2457600 blocks *** An error occurred during the file system check. *** Dropping you to a shell; the system will reboot *** when you leave the shell. Give root password for maintenance (or type Control-D to continue): I ran mke2fs to locate the backup superblocks: mke2fs -n /dev/mapper/vg_voinet01-lv_log . . . Superblock backups stored on blocks: 32768, 90304, 163840, 229376, 294912, 819200, 884736, 1605632 and ran: e2fsck -b 32768 /dev/mapper/vg_voinet01-lv_log The superblock could not be read or does not describe a correct ext2 The same thing happened for the next backup superblock addrees. And all the rest reported an invalid argument error from e2fsck. Is this recoverable? How? -- *** e-Mail is NOT a SECURE channel *** Do NOT transmit sensitive data via e-Mail Do NOT open attachments nor follow links sent by e-Mail James B. Byrne mailto:ByrneJB@Harte-Lyne.ca Harte & Lyne Limited http://www.harte-lyne.ca 9 Brockley Drive vox: +1 905 561 1241 Hamilton, Ontario fax: +1 905 561 0757 Canada L8E 3C3

3 2

xinetd custom service - perl - remote address
by Gary Stainburn 28 May '20

28 May '20

Hi all, I can't believe that I can't find the answer to this one. I have a perl script which is called by xinetd. I want that perl script to be able to detect the remote IP address of the caller. I presumed that it would be an environment variable but I could be wrong. I've found reference to the ENV and PASSENV arguments for xinetd.conf but no examples, and no indication of what auguments to use. In my script I have the following code: foreach (keys %ENV) { print "$_=$ENV{$_}\n";} but the only line I get back is: XINETD_LANG=en_US

5 5

Adobe digital editions?
by mark 28 May '20

28 May '20

I had it installed, running under WINE on CentOS 6. Bought a ebook, it insisted it needed ADE, I d/l from the sellers site... setup.exe won't run. Tried d/l 4.5 and 3 from Adobe, neither installer works, The one from their website: file setup.exe setup.exe: PE32 executable (GUI) Intel 80386, for MS Windows, Nullsoft Installer self-extracting archive Anyone run into this yet? I have books I *bought*, and I want them.... mark

6 15

IPv6 inbound routing
by Kenneth Porter 26 May '20

26 May '20

I see my ISP's gateway sending me neighbor solicitations to my external WAN interface for LAN clients on my internal LAN interface. How do I get the box to tell the ISP gateway that my box will route those addresses? I've been assigned a /56 and I'm using a /63 for the DMZ and a /64 for the LAN. The outbound packets seem to reach the destination server but nothing comes back. I'm assuming it's because the ISP router doesn't know to give my box the packets for the LAN clients. I'm using "tcpdump icmp6 -i em2" to watch the exchange. (For outbound routing, I have radvd configured to send router announcements to the LAN, and that seems to work, based on the packets I recieve from the LAN and from watching it with Wireshark on a Win10 client.)

1 0

Re: [CentOS] ip6tables equivalent for NAT?
by John Pierce 26 May '20

26 May '20

with ipv6, you just allow the specific ports destined to the specific local machine(s) in on your WAN side, they don't need translating. same sort of rule as if you had a internet-facing service running on the routing system On Tue, May 26, 2020 at 11:55 AM Kenneth Porter <shiva(a)sewingwitch.com> wrote: > I finally got an ISP connection with working IPv6 and now I need to add > firewall rules for forwarding connections from my LAN to the WAN. I'm > using > firewalld to handle the high-level description that gets translated to > iptables/ip6tables on CentOS 7. > > Of course, with IPv6, one doesn't do NAT, so the usual masquerade target > doesn't make sense. But I want similar connection logic, with no inbound > connections allowed to LAN clients and all outbound connections allowed. > How does one express this in either firewalld or its ip6tables "direct > rules"? > > I don't currently need port-forwarding to internal servers but, for > completeness, what would such rules look like? > > _______________________________________________ > CentOS mailing list > CentOS(a)centos.org > https://lists.centos.org/mailman/listinfo/centos > -- -john r pierce recycling used bits in santa cruz

3 3

ip6tables equivalent for NAT?
by Kenneth Porter 26 May '20

26 May '20

I finally got an ISP connection with working IPv6 and now I need to add firewall rules for forwarding connections from my LAN to the WAN. I'm using firewalld to handle the high-level description that gets translated to iptables/ip6tables on CentOS 7. Of course, with IPv6, one doesn't do NAT, so the usual masquerade target doesn't make sense. But I want similar connection logic, with no inbound connections allowed to LAN clients and all outbound connections allowed. How does one express this in either firewalld or its ip6tables "direct rules"? I don't currently need port-forwarding to internal servers but, for completeness, what would such rules look like?

1 0

network disconnection after several hours
by Thomas Poty 26 May '20

26 May '20

Hello, Here is the context during the problem occurs : We have a new machine running on centos 8.From this machine, we restore a postgresql dump on an other machine runnning on centos 7.After several hoursof running, restore fails due to a disconnection (no route to host).But, if we disable the firewall on centos 8, restore succeed. Before having this new centos 8 machine, we had a centos 7 machine and all worked fine with firewall activated. Has anyboby an ideas, clues or something else? Thanks, Thomas Poty

2 4

Thunderbird Revision Issues
by Mark LaPierre 25 May '20

25 May '20

Hey all, CentOS 6 has Thunderbird 68.8.0 CentOS 8 has Thunderbird 68.7.0 When I rsync my .thunderbird folder from my CentOS 6 machine to my CentOS 8 machine and start Thunderbird it says: "A newer version of Thunderbird may have made changes to your profile which are no longer compatible with this older version. Use this profile only with that newer version, or create a new profile for this installation of Thunderbird. Creating a new profile requires setting up your accounts, calendars and add-ons again." Needless to say, this is not an acceptable choice. I have several email accounts that would have to be set up. That's not such a big issue, but I have many local folders set up that I can't duplicate on the new installation if I can't use my previous profile. Does anyone know when CentOS 8 will catch up with CentOS 6 so that I can start using my new CentOS 8 box? Perhaps there is another work around. I've tried many of the solution provided on the mozilla web site to no avail. I even tried to install Thunderbird 68.8.0 on my CentOS 8 box. That didn't make it happy either. What now brown cow? -- _ °v° /(_)\ ^ ^ Mark LaPierre Registered Linux user No #267004 https://linuxcounter.net/ ****

4 5

mkfs.fat Device or resource busy
by Michael Hennebry 25 May '20

25 May '20

I'm trying to format a 16 GB SD card to FAT32. Either it won't find the device or it gives me the titular error message. mkfs.fat /dev/sdc I have tried "ejecting" the drive and reinserting the card. I have tried inserting another card, checking to insure that I could see its file, ejecting that card and inserting the target card. If I do not umount it, busy, if I don't, not found. What is the incantation for formatting an SD card. BTW I am using Centos 7 and a USB adapter. -- Michael hennebry(a)web.cs.ndsu.NoDak.edu "Sorry but your password must contain an uppercase letter, a number, a haiku, a gang sign, a heiroglyph, and the blood of a virgin." -- someeecards

2 2

authconfig vs authselect
by Leon Fauster 24 May '20

24 May '20

I had the habit to use authconfig --passalgo=sha512 --update but in EL8 its not supported anymore. The authselect-compat package is installed (and it says "not supported anymore and have no effect). Whats the equivalent call using the new tool "authselect"? -- Thanks Leon

2 1

Re: [CentOS] ether-wake
by Rich Greenwood 23 May '20

23 May '20

Some switch hardware can generate the packets directly, negating the need for a box on every VLAN. Meraki hardware can do it, but you have to go through the dashboard so automating it isn't currently possible. Here is some documentation on forwarding WoL on catalyst 3750 switches from Cisco: https://www.cisco.com/c/en/us/support/docs/switches/catalyst-3750-series-sw… -- Rich Greenwood Network Engineer Shasta County Office of Education 530-225-0161

4 4

External Array Data Migration
by Xinhuan Zheng 23 May '20

23 May '20

Dear All, Below question has been puzzled me for a while, and don’t know if anyone has experienced such puzzle: You have an external array attached to a physical hardware. The operating system is CentOS 5. The file system is created on top of LVM on external array & mounted. The CentOS 5 can see the array controller, and manage all LVM configuration, etc. There is data stored in that external array. At some point, you want to upgrade the operating system to higher version, CentOS 7. Is there a fast way to migrate the external array data volume to new hardware with CentOS 7 without doing machine-to-machine rsync the whole external array data volume? In another words, can I detach external array from old hardware, and attach it to new hardware, then re-configure LVM, so new operating system can recognize the external array file system? Thanks, - Xinhuan

2 1

Re: [CentOS] How to Load Custom CentOS 7 Image
by Xinhuan Zheng 21 May '20

21 May '20

Dear All, > It seems like kickstart is what you are looking for.? > Is this what you were trying to do? Yes, kickstart is what I’m looking for. Let me detail my provisioning process: * Provision a VM with standard CentOS 7 NetInstall ISO & my post script. The file system is created on top of LVM * Export entire VM as custom ISO image to be loaded into physical hardware * Kickstart physical hardware using above exported custom image & different grub/isolinux configuration Although I could just use the same CentOS 7 NetInstall ISO & run all my post script to the physical HW, it may take a few hours, since post script is long, and I wonder if above process will speed up, since the VM has everything needed. If that process isn’t feasible, then I’ll just do the same thing for physical hardware. Thanks, - Xinhuan

2 1

how does autofs deal with stuck NFS mounts and suspending to RAM?
by hw 21 May '20

21 May '20

Hi, after trying sshfs to mount a remote file system on a server with the result that sshfs will sooner or later get stuck and require a reboot of the client, I'm fed up with it and am looking for alternatives. So next I would like to use NFS over a VPN connection instead. To minimize the instances of the NFS mount getting stuck, it might be helpful to use autofs. What happens when the mount is stuck because the connection is down and autofs figures the idle timeout has expired and tries to unmount the remote file system? What happens when I put the client to sleep by suspending to RAM? Will autofs automatically unmount first, or will the server have to deal with a client that has apparently gone away and might re-appear later in unexpected ways? Is there a way to tell NFS to retry an operation _now_ after the connection went down and came back, rather than having to wait for a possibly rather long time? Is there a better alternative for mounting remote file systems over unreliable connections?

5 7

Re: [CentOS] How to Load Custom CentOS 7 Image
by Xinhuan Zheng 20 May '20

20 May '20

Dear Earl Ramirez, >I created a custom ISO a couple of years ago [0], you can use it as >your base of one of the following links[1-4], should be sufficient to >get you started. >[0] https://github.com/EarlRamirez/snipeit_iso In above github project, in https://github.com/EarlRamirez/snipeit_iso/blob/master/isolinux/grub.conf file, there is ‘@‘ symbol for splashimage, and for kernel, @KERNELPATH@, @ROOT@, etc. Will those be replaced by actual values? Where do actual values come from? How does actual values substitute those variables? Thanks again, - Xinhuan

2 1

Transparent Squid and FirewallD : fine-tuning question
by Nicolas Kovacs 19 May '20

19 May '20

Hi, I just setup a very basic HTTP proxy with Squid on a router running CentOS 7. Up until early 2020 I've been using a bone-headed shell script with iptables to configure my firewall. But I decided to follow advice from a few gurus on this list, and I've since moved my configurations to FirewallD, which works nicely. There's one configuration left to tackle, that's port redirection for the Squid proxy server. Which also works fine, though I'd like to figure out a little detail. Here goes. My router has two network interfaces, which I've aptly named WAN and LAN in the NetworkManager configuration: $ nmcli con show NAME UUID TYPE DEVICE WAN 9574b606-8f6d-3edc-95ad-8165df0f3fce ethernet enp2s0 LAN c726b168-1fcd-4dc5-a01d-8ad8a1ba38ee ethernet enp3s1 Squid is acting as a transparent proxy server: $ sudo grep http_port /etc/squid/squid.conf http_port 3128 transparent In my firewall configuration, all requests to port 80 (HTTP) are redirected to port 3128: $ sudo firewall-cmd --permanent --add-forward-port=port=80:proto=tcp:toport=3128:toaddr=192.168.3.1 $ sudo firewall-cmd --reload $ sudo firewall-cmd --list-all internal (active) target: default icmp-block-inversion: no interfaces: enp3s1 sources: services: dhcp dns http squid ssh ports: protocols: masquerade: no forward-ports: port=80:proto=tcp:toport=3128:toaddr=192.168.3.1 source-ports: icmp-blocks: rich rules: In the current state, this configuration works as expected. When a client desktop in the 192.168.3.0/24 network browses HTTP sites on the web, it appears in the Squid log on the server in /var/log/squid/access.log. And here comes the question. How can I redirect all HTTP requests to port 3128 EXCEPT THOSE THAT ARE DIRECTLY AIMED AT THE PROXY SERVER? Here's the thing. The proxy server (amandine.sandbox.lan) is also running httpd to display a static information page for the local network. Now client desktops can access http://amandine.sandbox.lan in a web browser just fine. But this still goes through the proxy, and I'd like these requests to rather be handled directly. In iptables syntax this would vaguely look like this: $ iptables -A PREROUTING -t nat -i 192.168.3.1 -p tcp \ ! -d 192.168.3.1 --dport 80 -j REDIRECT --to-port 3128 How can I translate the "! -d 192.168.3.1" part into some FirewallD-specific syntax ? Cheers from the sunny South of France, Niki -- Microlinux - Solutions informatiques durables 7, place de l'église - 30730 Montpezat Site : https://www.microlinux.fr Mail : info(a)microlinux.fr Tél. : 04 66 63 10 32 Mob. : 06 51 80 12 12

7 11

Centos8.1 Plymouthd crash 913: ply_event_loop_watch_for_timeout: Assertion `seconds > 0.0' failed.
by LAHAYE Olivier 18 May '20

18 May '20

Hi, I’m running a special initrd generated for SystemImager with a special dracut module that relies on plyouth scripted theme. It works perfectly on CentOS-6, CentOS-7, OpenSUSE-42.3, Fedora-29 (not tested later) and used to work on CentOS-8.0 Since CentOS-8.1 was released, IT chrashes with the following error: Plymouthd crash 913: ply_event_loop_watch_for_timeout: Assertion `seconds > 0.0' failed. I’m running quemu 5.0.0 with tianocore UEFI bios on MacOS (using accel=none or accel=hvf) (Bug also occurs with standard 256k bios) When I strace, I see multiple reasons but I can’t tell wich one is fatal. 1/ plymouthd reads /etc/Plymouth/plymouthd.conf (ok), then tries to read them from /var/run/plymouth/themes/<themename> instead of /usr/share/plymouth/themes/<themename>/ . As it fails it tries to read /var/run/plymouth/plymouthd.defaults (fails) then /usr/share/plymouth//plymouthd.defaults (ok) then it tries to read the theme /var/run/plymouth/themes/<themename>/<themename>.plymouth (fails) but never tries to read in from /usr/share/plymouth/themes/<themename>/<themename.plymouth> ??? It still continues 2/ After a few things, it tries to read /sys/devices/virtual/drm/ttm/uevent (ok) and the it tries to read /run/dev/data/+drm:ttm (fail). Is it expectable or does this means a problem like a missing udev rule or a boch driver bug or something else? 3/ Same as step 2 4/ Crash with @lymouthd: ply-event-loop.c:913: ply_event_loop_watch_for_timeout: Assertion `seconds > 0.0' failed. I’ve reported this in Centos-8.1 with no return and then RedHat-8.1 today. RedHat 8.1 bug report: https://bugzilla.redhat.com/show_bug.cgi?id=1836828 CentOS-8.1 bug report: https://bugs.centos.org/view.php?id=17140 Any idea where I could look for? More likely a plymouth bug or an udev missing rule or something else? (full dmesg and strace log in bug reports) Thanks a lot for any tips. PS: looking at google results, the only things I can find are very old bugs without resolution (not fixed and obsoleted due to new OS release) -- Olivier LAHAYE

1 0

Live Patching Upgrade CentOS 7
by Xinhuan Zheng 18 May '20

18 May '20

Dear All, Does anyone know how to to live patching upgrade of CentOS 7 without rebuilding the whole boot volume? I have enough disk space in Boot volume. I don’t want to go through creating a new VM and install CentOS 7 patch release. Thanks, - Xinhuan

1 0

kvm: C8 as guest on C6 host / huge delay while booting
by Leon Fauster 18 May '20

18 May '20

Since C8.1 kvm guests have a huge delay while booting on a kvm host based on C6. This delay was not present with C8.0. The "pause" happend direct after the grub step. The VNC session shows only a "_" character. Any ideas what changes? -- Leon

3 4

Missing announcement for the latest kernel
by David Hrbáč 18 May '20

18 May '20

Hi, It seems that kernel-2.6.32-754.29.2 has not been announced on the maillist. https://access.redhat.com/errata/RHSA-2020:2103 Regards, DH

1 0

Stuck Centos 7 to 8 upgrade
by Frank M. Ramaekers Jr. 16 May '20

16 May '20

Four problems below: # dnf -y groupupdate "Core" "Minimal Install" bintray-tvheadend-stable 0.0 B/s | 0 B 00:00 Failed to synchronize cache for repo 'bintray-tvheadend-stable', ignoring this repo. Last metadata expiration check: 0:03:11 ago on Sat 16 May 2020 12:30:47 PM CDT. Error: Problem 1: package python3-hawkey-0.35.1-9.el8_1.x86_64 requires librpm.so.8()(64bit), but none of the providers can be installed - package python3-hawkey-0.35.1-9.el8_1.x86_64 requires librpmio.so.8()(64bit), but none of the providers can be installed - package python3-dnf-plugins-core-4.0.8-3.el8.noarch requires python3-hawkey >= 0.34.0, but none of the providers can be installed - cannot install both rpm-libs-4.14.2-26.el8_1.x86_64 and rpm-libs-4.11.3-43.el7.x86_64 - package dnf-plugins-core-4.0.8-3.el8.noarch requires python3-dnf-plugins-core = 4.0.8-3.el8, but none of the providers can be installed - package deltarpm-3.6-3.el7.x86_64 requires librpm.so.3()(64bit), but none of the providers can be installed - package deltarpm-3.6-3.el7.x86_64 requires librpmio.so.3()(64bit), but none of the providers can be installed - conflicting requests - problem with installed package deltarpm-3.6-3.el7.x86_64 Problem 2: package python3-rhn-client-tools-2.8.16-13.module_el8.1.0+211+ad6c0bc7.x86_64 requires libgudev, but none of the providers can be installed - package python3-dnf-plugin-spacewalk-2.8.5-11.module_el8.1.0+211+ad6c0bc7.noarch requires python3-rhn-client-tools >= 2.8.4, but none of the providers can be installed - package libgudev-232-4.el8.i686 obsoletes libgudev1 < 230 provided by libgudev1-219-73.el7_8.6.x86_64 - package libgudev-232-4.el8.x86_64 obsoletes libgudev1 < 230 provided by libgudev1-219-73.el7_8.6.x86_64 - package dnf-plugin-spacewalk-2.8.5-11.module_el8.1.0+211+ad6c0bc7.noarch requires python3-dnf-plugin-spacewalk = 2.8.5-11.module_el8.1.0+211+ad6c0bc7, but none of the providers can be installed - package libgudev1-devel-219-73.el7_8.6.x86_64 requires libgudev1 = 219-73.el7_8.6, but none of the providers can be installed - conflicting requests - problem with installed package libgudev1-devel-219-73.el7_8.6.x86_64 Problem 3: package python3-dnf-4.2.7-7.el8_1.noarch requires dnf-data = 4.2.7-7.el8_1, but none of the providers can be installed - package dnf-4.2.7-7.el8_1.noarch requires python3-dnf = 4.2.7-7.el8_1, but none of the providers can be installed - cannot install both dnf-data-4.2.7-7.el8_1.noarch and dnf-data-4.0.9.2-1.el7_6.noarch - package yum-4.2.7-7.el8_1.noarch requires dnf = 4.2.7-7.el8_1, but none of the providers can be installed - package python2-dnf-4.0.9.2-1.el7_6.noarch requires dnf-data = 4.0.9.2-1.el7_6, but none of the providers can be installed - conflicting requests - problem with installed package python2-dnf-4.0.9.2-1.el7_6.noarch Problem 4: problem with installed package ipa-client-4.6.6-11.el7.centos.x86_64 - package ipa-client-4.6.6-11.el7.centos.x86_64 requires libcollection.so.2()(64bit), but none of the providers can be installed - package ipa-client-4.8.0-10.module_el8.1.0+255+aa2bdb39.x86_64 requires libxmlrpc_util.so.4()(64bit), but none of the providers can be installed - cannot install both libcollection-0.7.0-39.el8.x86_64 and libcollection-0.7.0-32.el7.x86_64 - cannot install both xmlrpc-c-1.51.0-5.el8.x86_64 and xmlrpc-c-1.32.5-1905.svn2451.el7.x86_64 - package sssd-kcm-2.2.0-19.el8_1.1.x86_64 requires libcollection.so.4()(64bit), but none of the providers can be installed - package libreport-plugin-mantisbt-2.1.11-53.el7.centos.x86_64 requires libxmlrpc_util.so.3()(64bit), but none of the providers can be installed - conflicting requests - problem with installed package libreport-plugin-mantisbt-2.1.11-53.el7.centos.x86_64 - package ipa-client-4.8.0-11.module_el8.1.0+253+3b90c921.x86_64 is excluded - package ipa-client-4.8.0-13.module_el8.1.0+265+e1e65be4.x86_64 is excluded (try to add '--allowerasing' to command line to replace conflicting packages or '--skip-broken' to skip uninstallable packages) Ideas? -Frank

2 1

CentOS 7 - xfs shrink & expand
by Frank M. Ramaekers Jr. 16 May '20

16 May '20

I'm having some difficulty finding a method to shrink my /home to expand my /. They both correspond to LVMs. It is my understanding that one cannot shrink a xfs filesystem. One must back it up (xfsdump), remove (lvremove) redefine it and then restore it back (xfsrestore). Okay, I'm running into a problem where /home needs to be "unused". If tried going in to "maintance mode", but I ran into a problem with the mount command (after issuing a 'chroot /sysroot'). I then tried using SystemRescueCD to boot to, but it wouldn't mount my 32TB RAID USB drive (something about too big). Any thoughts or suggestions? -Frank

5 8

CentOS 8 latest sssd src RPM
by Juan Jose Villaplana Querol 16 May '20

16 May '20

Hi, I can find latest sssd RPM at http://mirror.centos.org/centos/8.1.1911/BaseOS/x86_64/os/Packages/sssd-2.2…, but I can't find his source RPM at http://vault.centos.org/8.1.1911/BaseOS/Source/SPackages/ ( https://centos.pkgs.org/8/centos-baseos-x86_64/sssd-2.2.0-19.el8_1.1.x86_64… ) Is there something wrong with latest sssd src RPM? I have also noticed that retrieving src rpms via 'dnf download --source' doesn't work with the default CentOS-Sources.repo configuration. This has been reported here: https://bugs.centos.org/view.php?id=17120 Best regards, Juanjo -- Juan José Villaplana Querol/Servei d'Informàtica/Universitat Jaume I

1 0

Create Virtualbox image from running system?
by Frank Cox 16 May '20

16 May '20

I see that Microsoft has a utility that (apparently) can read a running system and create an image that can then be imported and run on Virtualbox. https://docs.microsoft.com/en-us/sysinternals/downloads/disk2vhd "You can even have Disk2vhd create the VHDs on local volumes, even ones being converted (though performance is better when the VHD is on a disk different than ones being converted)." Is there anything that does the same thing for Linux, and can image a system like that while it's actually running? -- Can we uninstall 2020 and install it again? This one has a virus. MELVILLE THEATRE ~ Real D 3D Digital Cinema ~ www.melvilletheatre.com

2 1

Ailing MATE desktop
by Robert G (Doc) Savage 16 May '20

16 May '20

I need some C8 troubleshooting help with MATE. I'm building a ZFS storage server with a SuperMicro H11SSL motherboard, EPYC 7232 CPU, and 32 GB ECC SDRAM. I installed CentOS 8.1.1911 from the iso as soon as it was released. I'm using the on-board ASPEED VGA video. I installed MATE v1.22 from https://copr.fedorainfracloud.org/coprs/stenstorp/MATE/. The following packages are installed: libmateweather-data-1.24.0-2.el8.noarch libmatemixer-1.24.0-1.el8.x86_64 mate-desktop-libs-1.24.0-3.el8.x86_64 mate-terminal-1.24.0-2.el8.x86_64 mate-themes-3.22.21-1.el8.noarch mate-panel-libs-1.22.2-1.el8.x86_64 mate-desktop-1.24.0-3.el8.x86_64 mate-settings-daemon-1.22.1-2.el8.x86_64 mate-polkit-1.24.0-2.el8.x86_64 mate-notification-daemon-1.22.1-1.el8.x86_64 mate-media-1.24.0-2.el8.x86_64 mate-power-manager-1.22.2-1.el8.x86_64 mate-system-log-1.22.2-2.el8.x86_64 libmateweather-1.24.0-2.el8.x86_64 libmatekbd-1.24.0-1.el8.x86_64 mate-utils-common-1.22.2-2.el8.noarch mate-disk-usage-analyzer-1.22.2-2.el8.x86_64 mate-user-guide-1.24.0-1.el8.noarch mate-menus-preferences-category-menu-1.24.0-2.el8.x86_64 mate-dictionary-1.22.2-2.el8.x86_64 mate-menus-1.24.0-2.el8.x86_64 mate-session-manager-1.24.0-1.el8.x86_64 mate-backgrounds-1.24.0-1.el8.noarch mate-search-tool-1.22.2-2.el8.x86_64 mate-panel-1.22.2-1.el8.x86_64 mate-system-monitor-1.24.0-1.el8.x86_64 mate-applets-1.24.0-2.el8.x86_64 mate-control-center-1.22.2-2.el8.x86_64 mate-icon-theme-1.24.0-1.el8.noarch mate-control-center-filesystem-1.22.2-2.el8.x86_64 mate-menus-libs-1.24.0-2.el8.x86_64 mate-user-admin-1.5.1-3.el8.x86_64 mate-calc-1.24.0-2.el8.x86_64 mate-screenshot-1.22.2-2.el8.x86_64 mate-screensaver-1.24.0-2.el8.x86_64 About two weeks ago following a reset, after a normal login an incomplete MATE desktop appeared. The background is black. There is no visible mouse, although there is some ghostly pixel movement in the top toolbar when what should be the mouse cursor floats over each of those toolbar icons. I can hit Enter and start whatever app the ghost cursor is over, and the mouse works only within that app's window. I'm a long-time user of MATE ever since GNOME3 was released, but until now I've never had any problems with it. I have no idea where to start troubleshooting. I've looked in journalctl, systemctl, and dmesg, but found nothing obvious. There's nothing in the MATE wiki to help. I'm open to any suggestions where to start looking. --Doc Savage Fairview Heights, IL

5 10

Can't move to Centos 8
by david 15 May '20

15 May '20

Folks I've been trying to convert my systems to Centos 8, seeing the EOL on the horizon a few years away. One of my systems is a Mac-Mini, and support for that has been discontinued. I'm wondering what the community suggests among these alternatives: 1) Stay with Centos 7 even after EOL hoping market pressures will add Mac-Mini support 2) Spend a few hundred dollars on a small, **quiet** replacement (ugh) 3) Convert to the Debian/Ubuntu distro. 4) Hope someone figures out a solution. By the way, the same issue exists, I believe, also for other Mac products, such as the newer laptops and servers. David

9 9

CentOS 8 Client to Windows file share SSO Active Directory
by DHilsbos＠performair.com 15 May '20

15 May '20

All; My Google foo is failing me, and searching through the last 10 months on this mailing list hasn't helped either. We have an existing Active Directory domain set up, and I'd like to add a CentOS 8 Workstation to it. I have experience using both realmd and manual configuration to allow local login with AD accounts to various Linux distribution, and have this working on my test system. I used realmd this time, and it configured sssd. I have one problem that I've never been able to solve; when I attempt to connect to a remote file server, while logged on to the CentOS 8 system using a domain account, it asks for credentials. Theoretically, this should work as it's just Kerberos. Can anyone point me at resources on what is needed for SSO to domain resources to work properly? This may be related to another issue that I'm seeing; I don't see the CentOS 8 user logon event (event ID 4624) on the Domain Controller. I see lots of logon events for the computer account, but none for the user account. Thank you, Dominic L. Hilsbos, MBA Director - Information Technology Perform Air International Inc. DHilsbos(a)PerformAir.com www.PerformAir.com

2 1

Re: [CentOS] Can't move to Centos 8
by Mauricio Tavares 15 May '20

15 May '20

On Thu, May 14, 2020 at 1:46 AM Kenneth Porter <shiva(a)sewingwitch.com> wrote: > > --On Wednesday, May 13, 2020 8:22 PM -0400 Mauricio Tavares > <raubvogel(a)gmail.com> wrote: > > > 1) Have you considered moving the storage business to another host so > > not to have a single point of failure? > > 2) Would a $60 Raspberry Pi 4GB be a good replacement? 2 USB3 ports > > and 1 GB ether port. My Synology storage appliance thingie is much > > dumber than that and has not missed a beat in years. > > I'm using CentOS 7 and 8 for internal servers but use OpenWrt on a consumer > router to do the fancy traffic balancing with the "cake" traffic control > module, something the old kernel in CentOS 7 lacks. > Funny you mentioned the OpenWrt: I have been using one as access point and realized I not only forgot how to but cannot find info (I remember seeing it years ago) on how to run the 2.4 and 5GHz as separate networks. Well, I can't even get the internal dhcp to work, having to forward all that to my bind/dhcp vm guest. Shame on me, as if I get that working I can then think on putting a vpn between wireless and internal networks which is something I really should be doing. > I'm running an email server with Dovecot IMAP, Spamassassin, and ClamAV and > that's a bit of a load so I suspect a Pi would be underpowered for that. > I really think it depends on the load, and only you have access to the performance info to answer that. There are people running all that in docker containers (I could swear I read about an "official" or "officially blessed" postfix container in the postfix mailing list).

2 1

How to Load Custom CentOS 7 Image
by Xinhuan Zheng 14 May '20

14 May '20

Dear All, I want to create a CentOS 7 VMWARE VM. I need to install various Runtime libraries, e.g., Tomcat, into the VM. Once all looks good, then I want to make a Custom Image of the entire VM. Later I want to load this Custom Image to a physical HW, so that I don’t need to go through all kinds Runtime installation. Does anyone know how to handle creating a Custom Image and Load to physical HW process? How does boot loader work when VM vs Physical HW has different devices? Thank you, - Xinhuan

2 1

Default ACL inheritance question
by James Pearson 14 May '20

14 May '20

A bit of a minor off-topic issue, but on the off-chance that someone understands how ACLs work ... I've been trying to see if using default ACLs would help with the following issue: I have a third party application that is running as a non-root user ('user-a') and creating log files with mode 0600 (read/write only to the owner) in a log directory I have another application that runs as another non-root user ('user-b') that needs to read the log files created by 'user-a' I can't change the mode of the log files generated by 'user-a', but I thought I could add a default ACL to the log file's parent directory that gave read access to 'user-b' - i.e. something like: % sudo setfacl -d -m u:user-b:r logdir % getfacl logdir # file: logdir # owner: user-a # group: user-a user::rwx group::r-x other::r-x default:user::rwx default:user:user-b:r-- default:group::rwx default:mask::rwx default:other::r-x Now when new log files are created in logdir, the default ACL is inherited, but 'user-b' still can't read the files - i.e. % getfacl logdir/logfile # file: logdir/logfile # owner: user-a # group: user-a user::rw- user:user-b:r-- #effective:--- group::rwx #effective:--- mask::--- other::--- i.e. the effective access for 'user-b' is '---' - which is no access to read for 'user-b' I'm not sure where 'effective' comes from? If I now explicitly add a read ACL for user-b to logdir/logfile: % sudo setfacl -m u:user-b:r logdir/logfile % getfacl logdir/logfile # file: logdir/logfile # owner: user-a # group: user-a user::rw- user:user-b:r-- group::rwx mask::rwx other::--- and 'user-b' can read logdir/logfile I guess I'm missing something on how default ACLs are meant to work - can anyone explain what is happening here or point me in the right direction ? I've actually 'solved' the issue with a suitable sudoers rule that allows 'user-b' to run the required command as 'user-a', but I would like to find out why this default ACL method doesn't work Thanks James Pearson

2 2

CentOS 8 updates
by Bill Maidment 13 May '20

13 May '20

Hi Is it my imagination/impatience, but I don't seem to have received any updates to CentOS 8 recently. I'm thinking particularly of firefox which was updated in CentOS 7 for a critical security update. Is there a backlog of CentOS 8 updates behind the 8.2 release? I noticed on a few occasions that my local mirroring had picked up and later deleted a lot of "tmp" files for CentOS 8, is that an indication that something is on the way? I understand that everyone is struggling with Covid19 restrictions, so just tell me to get back into my isolation if I'm just a bit too impatient. -- Cheers Bill

3 2

How to get CentOS 8 on AWS
by Thomas Stephen Lee 13 May '20

13 May '20

Hi, I am user of CentOS 8. When can we expect an image on AWS? I am just learning AWS and would like to use CentOS 8 for that. thanks --- Lee

3 3

Jitsi Meet on CentOS 7 ?
by Nicolas Kovacs 13 May '20

13 May '20

Hi, Anyone here managed to run Jitsi Meet on a CentOS 7 server ? As far as I can tell, it's one of the nicer open source videoconferencing solutions out there. I gave it a spin on https://suricate.tv and now I'd like to install it on one of my servers. Unfortunately the Jitsi developers only provide documentation for Debian/Ubuntu. Well, there is some sort of guide for CentOS around. As far as I can tell, the purpose of this guide is to encourage CentOS users to switch to Debian/Ubuntu. :o) Anyway, if you have a pointer to some comprehensible docs, I'd be grateful. Cheers, Niki -- Microlinux - Solutions informatiques durables 7, place de l'église - 30730 Montpezat Site : https://www.microlinux.fr Mail : info(a)microlinux.fr Tél. : 04 66 63 10 32 Mob. : 06 51 80 12 12

5 12

Monitoring network traffic to a host
by Ian Pilcher 13 May '20

13 May '20

Background - I am having an issue with occassional pauses when streaming high-bitrate media across my home network to my smart TV. I *suspect* that the root cause is the (incredibly lame) 100 Mbps Ethernet interface in the TV. In order to confirm that the peak bitrate really does max out the 100 Mbps connection, I'd like to monitor the communication between my NAS and the TV. The two devices are on separate VLANs, with routing performed by a CentOS 7 system, so it should theoretically be relatively simple to use an appropriate utility on the "router" to monitor and, if possible, graph the network traffic going to the TV. Ideally, I could run said utility for the entire time that the media file is playing and then look at its pretty graph to check if/when the bitrate hit 100 Mbps. Being able to watch the pretty graph in real time through a web interface would be nice as well, but is not required. Is any such program included in CentOS 7 or EPEL 7? The closest thing that I've found thus far is iftop (despite its lack of pretty). Unfortunately, it won't allow me to see the peak bitrate over the whole period in which the media is playing. Thanks for any suggestions! -- ======================================================================== In Soviet Russia, Google searches you! ========================================================================

3 3

xvidtune powertools CentOS 8
by Jerry Geis 13 May '20

13 May '20

Hi All - I was looking all over for xvidtune on Centos 8. could not find it. tried yum provides "*/xvidtune" tried yum search xvidtune Google pointed me to: https://centos.pkgs.org/8/centos-powertools-x86_64/xorg-x11-apps-7.7-21.el8… So I installed the apps and of course xvidtune is part of that. However just curious why the provides or search did not point me there ? Should it have? Thanks, Jerry

2 1

CentOS 7 disable the the hot corner
by Jerry Geis 12 May '20

12 May '20

I have loaded the gnome-shell-extension-no-hot-corner-3.28.1-11.el7.noarch and also the gnome-tweaks. When I run gnome-tweaks no where in there do I find the disable hot corner. where is that ? Its annoying when the mouse goes to the upper left and all the windows shrink. I wish to disable it. Thanks. Jerry

2 1

no images from www.imdb.com
by Michael Hennebry 12 May '20

12 May '20

For some reason, I no longer seem to get images from www.imdb.com , i.e. Internet Movie DataBase. The effect is really weird. I get from Firefox, Konqueror and Chromium. I'm running Centos 7. It's been happening for a few months now, so I really cannot tell what changed that mioght have caused it. How do I debug and fix this? Chromium still asks me for passwords a lot. I expect that is a separate issue. -- Michael hennebry(a)web.cs.ndsu.NoDak.edu "Sorry but your password must contain an uppercase letter, a number, a haiku, a gang sign, a heiroglyph, and the blood of a virgin." -- someeecards

3 3

XFS problem
by Gestió Servidors 11 May '20

11 May '20

Hello, My server is running kernel 3.10.0-1062.12.1 in a CentOS Linux release 7.7.1908. Since some weeks ago, server is restarting after XFS errors. Logs in /var/crash reported this information: [...] [443804.295916] sd 0:0:0:0: [sda] FAILED Result: hostbyte=DID_NO_CONNECT driverbyte=DRIVER_OK [443804.295919] sd 0:0:0:0: [sda] CDB: Read(10) 28 00 04 53 e8 b0 00 00 28 00 [443804.295922] blk_update_request: I/O error, dev sda, sector 72607920 [443804.295969] sd 0:0:0:0: rejecting I/O to offline device [443804.296245] sd 0:0:0:0: rejecting I/O to offline device [443804.296288] systemd-journal[946]: segfault at 55f73081c820 ip 000055f73081c820 sp 00007fffb3c0f558 error 15 [443804.321330] sd 0:0:1:0: [sdb] tag#35 FAILED Result: hostbyte=DID_OK driverbyte=DRIVER_TIMEOUT [443804.321335] sd 0:0:1:0: [sdb] tag#35 CDB: Write(16) 8a 00 00 00 00 02 67 e3 f5 f8 00 00 02 00 00 00 [443804.321338] blk_update_request: I/O error, dev sdb, sector 10332927480 [443804.321376] sd 0:0:0:0: rejecting I/O to offline device [443804.321384] XFS (dm-2): metadata I/O error: block 0xf00001 ("xfs_trans_read_buf_map") error 5 numblks 1 [443804.321390] XFS (dm-2): xfs_do_force_shutdown(0x1) called from line 239 of file fs/xfs/libxfs/xfs_defer.c. Return address = 0xffffffffc073a90b [443804.321421] sd 0:0:0:0: rejecting I/O to offline device [443804.321431] XFS (dm-2): metadata I/O error: block 0x1e04cee ("xlog_iodone") error 5 numblks 64 [443804.321433] XFS (dm-2): xfs_do_force_shutdown(0x2) called from line 1238 of file fs/xfs/xfs_log.c. Return address = 0xffffffffc077b210 [443804.321442] XFS (dm-2): Log I/O Error Detected. Shutting down filesystem [443804.321443] XFS (dm-2): Please umount the filesystem and rectify the problem(s) [443804.351688] Kernel panic - not syncing: Attempted to kill init! exitcode=0x0000000b [...] It seems problem are hard disk or XFS module, but physical RAID controller reports all hard disks are OK, so I suppose problem is XFS module. Also, I have read in this forum (https://bugs.centos.org/view.php?id=16960) something similar. Could someone say me is lastest kernel version for CentOS-7 (3.10.0-1127) solves this problem? Thanks.

2 1

CentOS 8 installer bug
by isdtor 11 May '20

11 May '20

CentOS 8.1.1911 has a bug in the installer. It is not possible to use more than one NFS repo via kickstart repo directive as the installer tries to mount all of them on /run/install/.nfs. You get this DBG payload: /run/install/.nfs already has something mounted on it message for all but the first one. The problem was reported for Fedora 29/30. https://bugzilla.redhat.com/show_bug.cgi?id=1669711 Do we know if this is fixed in RHEL 8.2?

1 0

DND Issues in Gnome (GTK3 regression)
by Leon Fauster 11 May '20

11 May '20

Does someone uses EL8 as a workstation (GUI) here? This bug is super annoying https://bugzilla.redhat.com/show_bug.cgi?id=1808900 and it seems not to get addressed in the current branch. How could a developer work with a forced delay in the UI (since a year now). Solution maybe in 8.3 ETA end of the year? Seems that all RH employees uses OSX as workstation (my impression of the summit) :-) This bug is located in gtk3 and should also hit non-GNOME users. Am I the only one here? Is CentOS Stream the workplace to address this bug? -- Leon

2 1

FAX
by Mark LaPierre 11 May '20

11 May '20

Hey All, Has anyone out there figured out how to send a FAX from a computer, sans FAX machine? -- _ °v° /(_)\ ^ ^ Mark LaPierre Registered Linux user No #267004 https://linuxcounter.net/ ****

3 2

Zoom....
by mark 10 May '20

10 May '20

Hi, folks, Updated CentOS 7 the other day. Updated zoom last night. Ancient (15 yr old) USB camera, Logitech QuickCam Express. If I run LD_PRELOAD=/usr/lib64/libv4l/v4l2convert.so cheese, I get video. Zoom, with or without the LD_PRELOAD - no video. I've tried stracing zoom, and created a file /etc/ld.so.preload, with the contents of /usr/lib64/libv4l/v4l2convert.so, and in strace, I see it loading it, but still no video. Anyone got any clues? Being a free end user, all zoom offers is the knowledge base.... mark

7 12

discord: things to do to run it.
by mark 10 May '20

10 May '20

Hi, folks, Installed discord last night, everything, including video worked, but not voice. As usual, I logged out last night before bed, and voice seems to work. Used the tgz, of course. HOWEVER, note that you *do* need to install libatomic for it to work properly, otherwise when it comes up, it says "the installation is corrupt", and the only button there, for help, is *ONLY* for Windows. I found through searching that it did need this. Install that, and no error message. mark

1 0

CentOS8 and proftpd with quota file module enable
by Dario Lesca 10 May '20

10 May '20

Hi, someone can help me on this follow problem? I have also write to proftpd ML and if someone give me some suggest I let you know. Many thanks for your reply. Dario ------- Messaggio inoltrato ------- Da: Dario Lesca <d.lesca(a)solinos.it> Rispondi a: proftp-user(a)lists.sourceforge.net A: proftp-user(a)lists.sourceforge.net Oggetto: [Proftpd-user] proftpd-1.3.6c on centos8: When mod_quotatab_file is enable, the get command give "get: Access failed: 550 aa.sh: No such file or directory" Data: Sat, 09 May 2020 11:51:00 +0200 Hello every body! this is my first post on this ML I have install (via dnf) and configure proftpd-1.3.6c on centos 8.1 up to date without modify the basic configuration file and add my modules configuration file under include folder /etc/proftpd/conf.d/ Then I have enable the mod_quotatab_file, configure it and initialize the Quota*Table file QuotaLimitTable file:/etc/proftpd/ftpquota.limittab QuotaTallyTable file:/etc/proftpd/ftpquota.tallytab All work fine except get command, when I try get a existent file uploaded, i obtain this error: "get: Access failed: 550 aa.sh: No such file or directory" The aa.sh file exist and it have the right access, see this example session: $ lftp -uftpste:mypass ftp://localhost -e 'site quota;ls aa.sh;lcd /tmp;get aa.sh;exit' 200-The current quota for this session are [current/limit]: Name: ftpste Quota Type: User Per Session: False Limit Type: Hard Uploaded Mb: 0.69/5000.00 Downloaded Mb: unlimited Transferred Mb: unlimited Uploaded files: unlimited Downloaded files: unlimited Transferred files: unlimited 200 Please contact root@localhost if these entries are inaccurate -rw-r--r-- 1 ftpste gftpste 33 Dec 3 14:31 aa.sh lcd ok, local cwd=/tmp get: Access failed: 550 aa.sh: No such file or directory I have investigate with debug enable and "strace -p" during get session and I have realize that when this modules is enable (if it's disable get work fine), the file is searched under / (/aa.sh) rather than into folder in which it is located: theuser's home in this case lstat("/aa.sh", 0x7ffe6dce9ed0) = -1 ENOENT (No such file or directory) If I create a empty file under / (touch /aa.sh) the get command work and the file obtained is the right file present into home folder. Is this a bug or there is some misconfiguration in my files? Many thanks for reply. -- Dario Lesca (inviato dal mio Linux Fedora 32 Workstation) _______________________________________________ ProFTPD Users List <proftpd-users(a)proftpd.org> Unsubscribe problems? http://www.proftpd.org/list-unsub.html -- Dario Lesca (inviato dal mio Linux Fedora 32 Workstation)

1 0

CentOS 8 CD Ripper
by Mark LaPierre 10 May '20

10 May '20

Hey all, Does anyone know of a CD ripper that will work with CentOS 8? I've found a great many that will work CentOS 6 and 7 but nothing that will build for CentOS 8. -- _ °v° /(_)\ ^ ^ Mark LaPierre Registered Linux user No #267004 https://linuxcounter.net/ ****

4 5

CentOS 7, zoom, and discord... konqueror
by mark 10 May '20

10 May '20

Firerox is my default browser, but both zoom and Discord pull up konqueror. Any idea why? mark

1 0

CentOS 8 and xvidtune and Nouveau
by Jerry Geis 09 May '20

09 May '20

I have an old laptop W530 I put CentOS 8 on. I was trying to install xvidtune - seems to not be available ? Thought that was part of X. Also trying to get Nouveau to be a higher resolution than 1024x768. I found the wiki, but adding video= to the kernel command line and regen grub did not do anything. Other documentation there seemed OLD. Anyone know how to correctly get Nouveau in 1920x1080? Thanks, Jerry

2 2

CentOS 8 installation
by isdtor 08 May '20

08 May '20

Are there still a lot of rough edges in this area? There are some things I simply can't get to work. This is about kickstart installations. Finding the right stuff for the %packages sections is lucky dip at best. The RHEL manual points to the comps file, really? This file isn't meant to be parsed by humans. Specifying an environment - the example "Infrastructure Server" doesn't exist. Is this one of the areas where CentOS deviates from RHEL? I did find server-product-environment, custom-environment, minimal-environment. I followed the link in the documentation to the kickstart file generator. The generated file isn't usable as is, specifically the %packages section - anaconda says there is no group dns-server, for instance. Which dnf later confirms. The group list in dnf also seems to be a lot shorter than it used to be under 7? Specifying %packages --multilib, this is where it breaks down completely. For the chosen group/package mix, which works perfectly without multilib, anaconda complains about conflicts for files provided by both the i686 and the x86_64 version of, in this case, gdb-headless and sssd-common. Attempting to fix this with -gdb-headless.i686 -sssd-common.i686 fails, these lines are being ignored. Excluding gdb-headless altogether fails also because the main gdb package pulls it in. Honestly, I'm not sure where to go from here.

2 3

libQt5Core.so ver 5.12
by cristiantorres110＠hotmail.com 08 May '20

08 May '20

Hello, For the last few days, 'dnf upgrade' on my Centos 8 installation has been showing problems saying that it cannot install the best update candidates for packages (kf5-*) because nothing provides libQtCore.so.5(Qt_5.12). My system shows that it presently has libQtCore.so.5(Qt_5.11). I've been keeping the system up to date using the --nobest option in dnf. I could download 'libqt5-core-5.12.8-alt3.x86_64.rpm ' from here and install it but I haven't dared to try. Is there an expectation for when version Qt_5.12 will be in the official repos? BR --Cristian

2 2

Chrony
by Jerry Geis 08 May '20

08 May '20

I just happened to notice this morning in /var/log/messages: chronyd[1299]: Selected source 207.244.103.95 host 207.244.103.95 95.103.244.207.in-addr.arpa domain name pointer dns-e.wdc-us.hosts.301-moved.de. Just curious why my machine in Indiana (USA) is asking for time in Germany. Wouldn't it use something closer ? Thanks, jerry

2 1

video problems
by mark 07 May '20

07 May '20

I've got an ancient USB videocam (QuickCam Express, yes, 15 years old). I got it working under C7, after I removed the default loaded gspca_spca561, and replaced it with the previous driver, gspca_spca508. It also needed zc3xx. Then I updated and rebooted my system a couple of days ago, and now no /dev/video, no errors.... Any clues? mark "other than waiting for a camera to arrive from China somewhere in June or July?"

1 2

repomd.xml.asc BAD signature in CentOS-7-x86_64-Minimal-2003.iso
by Pany 07 May '20

07 May '20

Hi list, I downloaded the CentOS-7-x86_64-Minimal-2003.iso ( sha256sum 659691c28a0e672558b003d223f83938f254b39875ee7559d1a4a14c79173193 ) and mount it on /mnt Unfortunately, It returned "BAD signature" when I verified the repodata/repomd.xml.asc So should I continue to use this ISO? Below is my procedure: # gpg --import /mnt/RPM-GPG-KEY-CentOS-7 gpg: key F4A80EB5: public key "CentOS-7 Key (CentOS 7 Official Signing Key) <security(a)centos.org>" imported gpg: Total number processed: 1 gpg: imported: 1 (RSA: 1) # gpg --fingerprint /root/.gnupg/pubring.gpg ------------------------ pub 4096R/F4A80EB5 2014-06-23 Key fingerprint = 6341 AB27 53D7 8A78 A7C2 7BB1 24C6 A8A7 F4A8 0EB5 uid CentOS-7 Key (CentOS 7 Official Signing Key) <security(a)centos.org> # gpg --verify /mnt/repodata/repomd.xml.asc gpg: Signature made Wed 22 Apr 2020 07:37:54 AM CST using RSA key ID F4A80EB5 gpg: BAD signature from "CentOS-7 Key (CentOS 7 Official Signing Key) <security(a)centos.org>"

1 0

du hung, wild display in ps
by Fred Smith 07 May '20

07 May '20

Hi! On Centos-7: $ cat /etc/centos-release CentOS Linux release 7.8.2003 (Core) Was running du to examine the sizes of my backups and found du hung, running "ps -eLf /mnt/backup/backups" shows this: # ps -eLf | grep du root 1185 1 1185 0 1 May01 ? 00:00:00 /usr/bin/abrt-watch-log -F Backtrace /var/log/Xorg.0.log -- /usr/bin/abrt-dump-xorg -xD root 1281 1 1281 0 1 May01 ? 00:00:01 /usr/bin/abrt-watch-log -F BUG: WARNING: at WARNING: CPU: INFO: possible recursive locking detected ernel BUG at list_del corruption list_add corruption do_IRQ: stack overflow: ear stack overflow (cur: eneral protection fault nable to handle kernel ouble fault: RTNL: assertion failed eek! page_mapcount(page) went negative! adness at NETDEV WATCHDOG ysctl table check failed : nobody cared IRQ handler type mismatch Kernel panic - not syncing: Machine Check Exception: Machine check events logged divide error: bounds: coprocessor segment overrun: invalid TSS: segment not present: invalid opcode: alignment check: stack segment: fpu exception: simd exception: iret exception: /var/log/messages -- /usr/bin/abrt-dump-oops -xtD root 11090 1 11090 11 1 15:08 pts/1 00:01:10 du -s /mnt/backup/backups even after killing the du. there were two DUs shown, I killed the parent (presumably the one I started) but the one that remains seems to be un-killable. This is what the output looked like before I killed du: # ps -eLf | grep du root 1185 1 1185 0 1 May01 ? 00:00:00 /usr/bin/abrt-watch-log -F Backtrace /var/log/Xorg.0.log -- /usr/bin/abrt-dump-xorg -xD root 1281 1 1281 0 1 May01 ? 00:00:01 /usr/bin/abrt-watch-log -F BUG: WARNING: at WARNING: CPU: INFO: possible recursive locking detected ernel BUG at list_del corruption list_add corruption do_IRQ: stack overflow: ear stack overflow (cur: eneral protection fault nable to handle kernel ouble fault: RTNL: assertion failed eek! page_mapcount(page) went negative! adness at NETDEV WATCHDOG ysctl table check failed : nobody cared IRQ handler type mismatch Kernel panic - not syncing: Machine Check Exception: Machine check events logged divide error: bounds: coprocessor segment overrun: invalid TSS: segment not present: invalid opcode: alignment check: stack segment: fpu exception: simd exception: iret exception: /var/log/messages -- /usr/bin/abrt-dump-oops -xtD root 11078 18627 11078 0 1 15:08 pts/1 00:00:00 sudo du -s /mnt/backup/backups root 11090 11078 11090 12 1 15:08 pts/1 00:01:10 du -s /mnt/backup/backups root 12125 19449 12125 0 1 15:17 pts/0 00:00:00 grep --color=auto du Oh, and I never did get the du out put I expected. Anyone got a clue? Thanks in advance! Fred -- ---- Fred Smith -- fredex(a)fcshome.stoneham.ma.us ----------------------------- "For the word of God is living and active. Sharper than any double-edged sword, it penetrates even to dividing soul and spirit, joints and marrow; it judges the thoughts and attitudes of the heart." ---------------------------- Hebrews 4:12 (niv) ------------------------------

2 2

Odd permissions
by mark 07 May '20

07 May '20

I've posted a couple times in the last month, that for some reason, since I rebuilt to CentOS 7 from 6 (same home directory, another partition, of course), when I log out, it restarts with me logged in, and only the second time I log out does it actually log me out. Still debugging that. I have logged in as root, and don't have the problem, so I'm assuming that it's something incompatible, or somehow mis-set in ~/.<whatever>. Looking in ~/.cache, I found something weird: ~/.cache/gnome-control-center, which had permissions of d-w-rwxr-T Say *what*? Anyone got a clue as to why? And while I'm looking for clues, does anyone have any thoughts as to where my issue might lie? mark

2 1

rpm command option
by Chris Olson 06 May '20

06 May '20

We located an application recommended by one of customers for sharing certain data. It was available for installation using a few different methods. Using yum was also recommended for the installation. The install instructions began with what appeared to be a fairly typical command as indicated below (with the URL slightly altered). sudo rpm --import https://rpm.xxxxx.com/rpmrepo.key To our junior employee assigned to perform the install on a test system, it seemed like a good idea to do some checking on the rpm option --import indicated in those instructions. They did not find the --import in any of the 14 pages of the CentOS 7 man page for rpm. Some Google searches indicated that the --import option does exist. The repo setup and application installation all went well and took only about three minutes. The app is also working as intended. Is there some good reason for --import being left out of the manual page?

5 4

Custom ISO
by Jerry Geis 06 May '20

06 May '20

Hi All, I am trying to make a customer ISO. When I run this command: mkisofs -o $DESTINATION_FILE -b isolinux/isolinux.bin -c boot.cat \ -no-emul-boot -boot-info-table \ -V "$NAME" -boot-load-size 4 -boot-info-table -R -J -v -T \ -eltorito-alt-boot -e images/efiboot.img \ $DESTINATION_DIR it tells me: Size of boot image is 4 sectors -> No emulation Size of boot image is 17408 sectors -> genisoimage: Error - boot image 'images/efiboot.img' has not an allowable size. This is the exact same file that is on the Everything ISO image. What am I missing ? I also want to make the ISO boot with UEFI. I think I have the right parameters but getting this error. Thoughts? Thanks, Jerry

3 6

Samba update to 4.10 (with c7.8) - broken -?
by lejeczek 05 May '20

05 May '20

hi guys I've just let the system to get big update to 7.8 and with it came new Samba(4.10.4-10.el7.x86_64), a version with now fails on my boxes for no apparent reasons. My Samba uses LDAP backend but I can see no errors related to that neither. ... [2020/05/05 15:53:37.093041, 0] ../../lib/util/become_daemon.c:136(daemon_ready) daemon_ready: daemon 'smbd' finished starting up and ready to serve connections [2020/05/05 15:53:37.106797, 2] ../../source3/smbd/server.c:1415(smbd_parent_loop) waiting for connections [2020/05/05 15:53:37.108770, 3] ../../source3/smbd/server_exit.c:236(exit_server_common) Server exit (termination signal) Failed to start Samba SMB Daemon. Unit smb-ccnr-biotec.service entered failed state. smb-ccnr-biotec.service failed. Are you seeing anything weir with your Sambas? many thanks, L.

1 1

Understanding VDO vs ZFS
by david 04 May '20

04 May '20

Folks I'm looking for a solution for backups because ZFS has failed on me too many times. In my environment, I have a large amount of data (around 2tb) that I periodically back up. I keep the last 5 "snapshots". I use rsync so that when I overwrite the oldest backup, most of the data is already there and the backup completes quickly, because only a small number of files have actually changed. Because of this low change rate, I have used ZFS with its deduplication feature to store the data. I started using a Centos-6 installation, and upgraded years ago to Centos7. Centos 8 is on my agenda. However, I've had several data-loss events with ZFS where because of a combination of errors and/or mistakes, the entire store was lost. I've also noticed that ZFS is maintained separately from Centos. At this moment, the Centos 8 update causes ZFS to fail. Looking for an alternate, I'm trying VDO. In the VDO installation, I created a logical volume containing two hard-drives, and defined VDO on top of that logical volume. It appears to be running, yet I find the deduplication numbers don't pass the smell test. I would expect that if the logical volume contains three copies of essentially identical data, I should see deduplication numbers close to 3.00, but instead I'm seeing numbers like 1.15. I compute the compression number as follows: Use df and extract the value for "1k blocks used" from the third column use vdostats --verbose and extract the number titled "1K-blocks used" Divide the first by the second. Can you provide any advice on my use of ZFS or VDO without telling me that I should be doing backups differently? Thanks David

8 10

perl Net::Interface module on CentOS 8
by sthustfo 04 May '20

04 May '20

We have received a perl program that makes use of "Net::Interface" module which I am trying to run on CentOS 8. However, running into issues as this module is not found. use Net::Interface; I could use cpan to install the same, but currently using the rpm packages for all the needs. Any idea which rpm package provides this perl module? Thanks.

3 2

Re: [CentOS] Understanding VDO vs ZFS
by david 03 May '20

03 May '20

0At 08:07 PM 5/2/2020, you wrote: >My two cents: >1- Do you have an encrypted filesystem on top of VDO? If yes, you will see >no benefit from dedupe. >2- can you post the stats of vdostats verbose /dev/mapper/xxxxx (replace >with your device) > >you can do something like: "vdostats -verbose /dev/mapper/xxxxxxxx | grep >-B6 'save percentage' > > > > >On Sat, May 2, 2020 at 9:54 PM david <david(a)daku.org> wrote: > > > Folks > > > > I'm looking for a solution for backups because ZFS has failed on me > > too many times. In my environment, I have a large amount of data > > <snip> BTW: I think the 'saving percent' of 13 is consistent with my computation of 1.16 if one takes into account the overhead blocks. Is that true?

1 0

systemctl restart changes permission.
by Kaushal Shriyan 02 May '20

02 May '20

Hi, I am running CentOS Linux release 7.8.2003 (Core) with php72u-fpm-7.2.30-1.el7.ius.x86_64 version. I am facing the below permission denied issue. I also did the below steps #cd /run #chown -Rc nginx.nginx php-fpm changed ownership of ‘php-fpm/php-fpm.pid’ from root:root to nginx:nginx changed ownership of ‘php-fpm’ from root:root to nginx:nginx #systemctl restart php-fpm again changes it from nginx.nginx to root.root user. nginx error logs > 2020/04/30 03:09:28 [crit] 17175#0: *154570 connect() to > unix:/run/php-fpm/www.sock failed (13: *Permission denied*) while > connecting to upstream, client: 49.207.54.161, server: _, request: "GET / > HTTP/1.1", upstream: "fastcgi://unix:/run/php-fpm/www.sock:", host: > "35.128.212.112" > 2020/04/30 03:09:28 [error] 17175#0: *154570 open() > "/var/www/drupal/web/50x.html" failed (2: No such file or directory), > client: 49.207.54.161, server: _, request: "GET / HTTP/1.1", upstream: > "fastcgi://unix:/run/php-fpm/www.sock", host: "35.128.212.112" > 2020/04/30 03:09:35 [crit] 17176#0: *154573 connect() to > unix:/run/php-fpm/www.sock failed (13: Permission denied) while connecting > to upstream, client: 49.207.54.161, server: _, request: "GET / HTTP/1.1", > upstream: "fastcgi://unix:/run/php-fpm/www.sock:", host: "35.128.212.112" > 2020/04/30 03:09:35 [error] 17176#0: *154573 open() > "/var/www/drupal/web/50x.html" failed (2: No such file or directory), > client: 49.207.54.161, server: _, request: "GET / HTTP/1.1", upstream: > "fastcgi://unix:/run/php-fpm/www.sock", host: "35.128.212.112" > 2020/04/30 03:09:49 [crit] 17175#0: *154575 connect() to > unix:/run/php-fpm/www.sock failed (13: Permission denied) while connecting > to upstream, client: 14.98.153.6, server: _, request: "GET / HTTP/1.1", > upstream: "fastcgi://unix:/run/php-fpm/www.sock:", host: "35.128.212.112" > 2020/04/30 03:09:49 [error] 17175#0: *154575 open() > "/var/www/drupal/web/50x.html" failed (2: No such file or directory), > client: 14.98.153.6, server: _, request: "GET / HTTP/1.1", upstream: > "fastcgi://unix:/run/php-fpm/www.sock", host: "35.128.212.112" > 2020/04/30 03:09:50 [crit] 17175#0: *154575 connect() to > unix:/run/php-fpm/www.sock failed (13: Permission denied) while connecting > to upstream, client: 14.98.153.6, server: _, request: "GET / HTTP/1.1", > upstream: "fastcgi://unix:/run/php-fpm/www.sock:", host: "35.128.212.112" > 2020/04/30 03:09:50 [error] 17175#0: *154575 open() > "/var/www/drupal/web/50x.html" failed (2: No such file or directory), > client: 14.98.153.6, server: _, request: "GET / HTTP/1.1", upstream: > "fastcgi://unix:/run/php-fpm/www.sock", host: "35.128.212.112" > 2020/04/30 03:10:46 [crit] 17176#0: *154578 connect() to > unix:/run/php-fpm/www.sock failed (13: Permission denied) while connecting > to upstream, client: 184.22.107.148, server: _, request: "GET / HTTP/1.1", > upstream: "fastcgi://unix:/run/php-fpm/www.sock:", host: "35.128.212.112" > 2020/04/30 03:10:46 [error] 17176#0: *154578 open() > "/var/www/drupal/web/50x.html" failed (2: No such file or directory), > client: 184.22.107.148, server: _, request: "GET / HTTP/1.1", upstream: > "fastcgi://unix:/run/php-fpm/www.sock", host: "35.128.212.112" Please let me know if you need any additional information. Thanks in Advance. Best Regards, Kaushal

2 2

fcitx and switching between keyboards
by H 01 May '20

01 May '20

This is an old issue for me running CentOS 7, latest update. I am using fcitx to switch between keyboards, two western ones and Chinese pinyin keyboard. Ever since I installed CentOS 7 over two years ago, I have been unable to resolve issues where I can maintain keyboard setting within one application, notably chromium, and/or between applications. fcitx has a setting for allowing the keyboard choice to remain across applications but it does not work - so far. Further, in chromium, even when within an IME, every time I hit ENTER, the keyboard resets back to the default (EN_US). Needless to say, this makes for some very tedious typing using an alternative keyboard. I do not have this problem remaining within a single IME in Thunderbird, nor in Firefox, nor in LibreOffice. I can switch back and forth between one of these apps and the keyboard switches back to what I last used in that app when switching back to the app - /provided I have used Chinese/. It does not work when I use different western keyboards in the various apps. Is anyone using fcitx switching between different keyboards and can confirm the above - or refute it?

1 0

dhcpd: Not searching LDAP
by Frank Cox 01 May '20

01 May '20

Whenever my dhcp server is restarted it always puts this entry into /var/log/messages: dhcpd: Not searching LDAP since ldap-server, ldap-port and ldap-base-dn were not specified in the config file This isn't earth-shattering news since I don't have a ldap server and there's no mention of ldap in /etc/dhcp/dhcpd.conf either. So is this an error message? If it's just an informational message then that's one thing, but if it's an error message then what's the problem that it's telling me about and how do I solve it? -- MELVILLE THEATRE ~ Real D 3D Digital Cinema ~ www.melvilletheatre.com

2 1

GNS3 installation docs for CentOS 8
by System Administrator 01 May '20

01 May '20

Hi, Does anyone have GNS3 installation guide for CentOS 8? Would be grateful if you could give me. Thank you. Sonam ****************************************************************************************************************************** Information contained in this message maybe confidential in nature and is meant for the intended recipient(s) of the message only. Tashi InfoComm Limited has the sole right to such information and any copying/redistribution of the information contained in the message, without the prior written consent of Tashi InfoComm Limited, is Prohibited. ******************************************************************************************************************************

3 4

CentOS-announce Digest, Vol 183, Issue 1
by centos-announce-request＠centos.org 01 May '20

01 May '20

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit https://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CEBA-2020:1982 CentOS 7 tzdata BugFix Update (Johnny Hughes) 2. CESA-2020:1509 Important CentOS 7 java-11-openjdk Security Update (Johnny Hughes) 3. CESA-2020:1512 Important CentOS 7 java-1.8.0-openjdk Security Update (Johnny Hughes) 4. CESA-2020:1507 Important CentOS 7 java-1.7.0-openjdk Security Update (Johnny Hughes) 5. CESA-2020:1511 Important CentOS 7 git Security Update (Johnny Hughes) 6. CESA-2020:1561 Important CentOS 7 python-twisted-web Security Update (Johnny Hughes) 7. CESA-2020:1489 Important CentOS 7 thunderbird Security Update (Johnny Hughes) 8. CESA-2020:1962 Important CentOS 6 python-twisted-web Security Update (Johnny Hughes) 9. CEBA-2020:1982 CentOS 6 tzdata BugFix Update (Johnny Hughes) ---------------------------------------------------------------------- Message: 1 Date: Thu, 30 Apr 2020 19:51:35 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CEBA-2020:1982 CentOS 7 tzdata BugFix Update Message-ID: <20200430195135.GA23919(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Bugfix Advisory 2020:1982 Upstream details at : https://access.redhat.com/errata/RHBA-2020:1982 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: bc5c790c0a346bb20abbbd866e0c1cf664cec9c3e4d4e21dbfe32b32616257ba tzdata-2020a-1.el7.noarch.rpm df284a4379294602228b360243cb0fc0498371278b702354b9de2cc38ffbc09f tzdata-java-2020a-1.el7.noarch.rpm Source: d348bae19f293c56bb60b0f65b3d3dcf4523128a36ee356f0c7231da1219d2f4 tzdata-2020a-1.el7.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Message: 2 Date: Thu, 30 Apr 2020 19:52:43 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CESA-2020:1509 Important CentOS 7 java-11-openjdk Security Update Message-ID: <20200430195243.GA24198(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Security Advisory 2020:1509 Important Upstream details at : https://access.redhat.com/errata/RHSA-2020:1509 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: feeefc6681aaa3bf69fdb9374e1dc13ed6e964b6545502f0bd14eaf7ce53f06d java-11-openjdk-11.0.7.10-4.el7_8.i686.rpm 7c4c37c0ea48f84107b282a1575f63a84f6f9cfbbc50708f77309afb46629be2 java-11-openjdk-11.0.7.10-4.el7_8.x86_64.rpm 5b7b7ad1f6a47aaaf64e78b1c3eaa439bc3d1fa487d4cf6d645f3e5f7f82aa1d java-11-openjdk-demo-11.0.7.10-4.el7_8.i686.rpm 0df0679e7cf1b5f15fda6bdd7d47f52bb042dd934055d93db063eba057f71d72 java-11-openjdk-demo-11.0.7.10-4.el7_8.x86_64.rpm 9ce3611a75397516fd6eac15d6b7e740ed3a497fdd49c77d03593701ad6f5bed java-11-openjdk-devel-11.0.7.10-4.el7_8.i686.rpm 7c16d75034f8b5af29f29368f9d6b6f0f96d206124bcede20b987cae23a8fc2b java-11-openjdk-devel-11.0.7.10-4.el7_8.x86_64.rpm ad579f5f54185a849e2c2f49818206dabd254d5b4a9f6a56eaaf828f8035d7ed java-11-openjdk-headless-11.0.7.10-4.el7_8.i686.rpm d59a5715f41d0cc42740ea8bbf254fee0729fe95f7783887470ac54e0028a645 java-11-openjdk-headless-11.0.7.10-4.el7_8.x86_64.rpm b8b135c555c96cb85f1b78394507e880cb3a0623d07f378b5ac2aee7ea0ceb2b java-11-openjdk-javadoc-11.0.7.10-4.el7_8.i686.rpm f8c301dd37d12af525a3f9515c8f316be1b0b45a896aff4aadbd54695c0202f3 java-11-openjdk-javadoc-11.0.7.10-4.el7_8.x86_64.rpm b65eaa6b5bbfc4d7f1c740a8b26fbe50a5a5fe48fd4d4cf6c418ad3245af136d java-11-openjdk-javadoc-zip-11.0.7.10-4.el7_8.i686.rpm e540cd84f0994771b455a98ad485737a20f0e818edbb3dc3c091e2679986872f java-11-openjdk-javadoc-zip-11.0.7.10-4.el7_8.x86_64.rpm 12b56a59045d9e0c7877d2cde5d82ff665bd0b98fc0fc87afca228ccd37f8be6 java-11-openjdk-jmods-11.0.7.10-4.el7_8.i686.rpm f7b5a8b2b137469210929ce36c6e37f56a328316f1424f3d4d004ec707e0f2ad java-11-openjdk-jmods-11.0.7.10-4.el7_8.x86_64.rpm bd5baed650742e2df7417aaf0faf09a3e1faa3d08ec1eab2b9ef618ffbb5b177 java-11-openjdk-src-11.0.7.10-4.el7_8.i686.rpm d0934f29f7538e5e971ebcc6b0f43f707af2699c32ac38f43aa18cdcb773cdfb java-11-openjdk-src-11.0.7.10-4.el7_8.x86_64.rpm Source: 987ea04496423b636a57918b0a1c49edb1ee626eff745721ea99c0877e64dc67 java-11-openjdk-11.0.7.10-4.el7_8.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Message: 3 Date: Thu, 30 Apr 2020 19:53:37 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CESA-2020:1512 Important CentOS 7 java-1.8.0-openjdk Security Update Message-ID: <20200430195337.GA24470(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Security Advisory 2020:1512 Important Upstream details at : https://access.redhat.com/errata/RHSA-2020:1512 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: ec734e220ac9e35c12a75bfd57bc8edac97facd2df5a1d03ce683d802b4c9fdd java-1.8.0-openjdk-1.8.0.252.b09-2.el7_8.i686.rpm f86917a54210c13a63bce8bb807947cdbc7cacc994acdd4c47b7d54e4b891104 java-1.8.0-openjdk-1.8.0.252.b09-2.el7_8.x86_64.rpm 45ee7e0f2042f58c6053003c233b795f0ad2c8ca26c2035d9332728c85f7341c java-1.8.0-openjdk-accessibility-1.8.0.252.b09-2.el7_8.i686.rpm dcac59f243f853c1da4e105b7c29f1eeb7ce15b9f271a6b36409660fd933be60 java-1.8.0-openjdk-accessibility-1.8.0.252.b09-2.el7_8.x86_64.rpm a9f65a8ea5f82e7465326d90fc08da7bba5e0a22da7a13503afbb430bb9e2634 java-1.8.0-openjdk-demo-1.8.0.252.b09-2.el7_8.i686.rpm 2e644a6a5b06af473181b288624993d4a0d2e821068d437e38da73cfcb5520ad java-1.8.0-openjdk-demo-1.8.0.252.b09-2.el7_8.x86_64.rpm bfe0e5a6ea3a1bc7dfdb62dbd19ba20a3eb4e531c416dd75ec01594ecd71b5d2 java-1.8.0-openjdk-devel-1.8.0.252.b09-2.el7_8.i686.rpm ecfa046985366a978f782b0e252d1b0b8027e231d3a1e89a72e6ad44e2d3d430 java-1.8.0-openjdk-devel-1.8.0.252.b09-2.el7_8.x86_64.rpm ddb19ff50033bc8f749c6974221b072059a020fdd393639f3c97d7b12fb17679 java-1.8.0-openjdk-headless-1.8.0.252.b09-2.el7_8.i686.rpm b21dace04c6c4fb78b7b3109d628f8719909d8bac028d312bfd124d393cbdfb7 java-1.8.0-openjdk-headless-1.8.0.252.b09-2.el7_8.x86_64.rpm 3d2dd4a1793923c8e0ccbf5a99a67d90fafa11076a69860dc3b88897867762eb java-1.8.0-openjdk-javadoc-1.8.0.252.b09-2.el7_8.noarch.rpm 06bb8b6b228e02cfa5c7686b98df704b16779b6fcda71a801d5acb409024228c java-1.8.0-openjdk-javadoc-zip-1.8.0.252.b09-2.el7_8.noarch.rpm 4dd4b147197c43a217f0a1e10ac10ce53346f5419e24476355e6f5dbdbaa63ba java-1.8.0-openjdk-src-1.8.0.252.b09-2.el7_8.i686.rpm 6f8df4b9604f4ec97936c1dbd04b99ede0e209670aac6e34cc4714888a470d29 java-1.8.0-openjdk-src-1.8.0.252.b09-2.el7_8.x86_64.rpm Source: 0482dd5996a91af5de3b7cbad8c1c22db6c3c1c4087e06a125bc13bb8bb824f7 java-1.8.0-openjdk-1.8.0.252.b09-2.el7_8.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Message: 4 Date: Thu, 30 Apr 2020 19:54:04 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CESA-2020:1507 Important CentOS 7 java-1.7.0-openjdk Security Update Message-ID: <20200430195404.GA24629(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Security Advisory 2020:1507 Important Upstream details at : https://access.redhat.com/errata/RHSA-2020:1507 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: fabe67fc9df555934da2d72279096fd3c24b3e2ff47850f5896505890f38a0a4 java-1.7.0-openjdk-1.7.0.261-2.6.22.2.el7_8.x86_64.rpm 03c15876c6039d9417ee91cd8c126e85728890c0197caf2eabe8ead3f490ede3 java-1.7.0-openjdk-accessibility-1.7.0.261-2.6.22.2.el7_8.x86_64.rpm 7575efaca8e9a5cf4f0a1e2248ccae845d3e59aaf7ae927486d923a3546dd141 java-1.7.0-openjdk-demo-1.7.0.261-2.6.22.2.el7_8.x86_64.rpm 2cbb801428afc2eb0a923e443936b9a998896d3b6b34a69344eafd09c4d900af java-1.7.0-openjdk-devel-1.7.0.261-2.6.22.2.el7_8.x86_64.rpm 91d7ddde31bd7f6dee89c8e4c710bf889e2f6e0dadb253de44f76a18c71fbd65 java-1.7.0-openjdk-headless-1.7.0.261-2.6.22.2.el7_8.x86_64.rpm 4116eb9fadf6555249e648b54b721e40488fd224f7f2c3c1ff3a97124b66a2fe java-1.7.0-openjdk-javadoc-1.7.0.261-2.6.22.2.el7_8.noarch.rpm 7b6b6a78638df33409453224096ef0e0201774bc67bdd1d5016f52b034f97e19 java-1.7.0-openjdk-src-1.7.0.261-2.6.22.2.el7_8.x86_64.rpm Source: 13bcf8e890d357b8d0963724df486217403817c19c2ac0c424513440296a4b99 java-1.7.0-openjdk-1.7.0.261-2.6.22.2.el7_8.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Message: 5 Date: Thu, 30 Apr 2020 19:55:06 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CESA-2020:1511 Important CentOS 7 git Security Update Message-ID: <20200430195506.GA24985(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Security Advisory 2020:1511 Important Upstream details at : https://access.redhat.com/errata/RHSA-2020:1511 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: b051121e45e0afb64ee88bcc0ac8571ff447ddce874c3d1a3fdf0f32c16967bf emacs-git-1.8.3.1-22.el7_8.noarch.rpm c6dd608f4399755307cbebe7a60524042017d162d3d58c7a9cbdf313917a09f7 emacs-git-el-1.8.3.1-22.el7_8.noarch.rpm 15f56ffd76f82179e50c87cdd6be86df7b86092748048012af41bd50848a4a34 git-1.8.3.1-22.el7_8.x86_64.rpm f3fc0ec55423631c0fa8458a3008ed09380b9c5deee9b3e930c32213376d6227 git-all-1.8.3.1-22.el7_8.noarch.rpm e442411450eb36b331314e705343178cfd4d00d3b65d86ceeb47b2b2a7695f8a git-bzr-1.8.3.1-22.el7_8.noarch.rpm 0c17dfb9729fc289765911713f403406c570032f053e439c510b1e0b08291732 git-cvs-1.8.3.1-22.el7_8.noarch.rpm b3d2535112b577451f3bd143e7f7bdf309b44a9d569f6391da00c0ef2ba9a37b git-daemon-1.8.3.1-22.el7_8.x86_64.rpm d49c9b174bd2b055533cbe4f0d552dff471663a2cb2e1d8d49c505083e326109 git-email-1.8.3.1-22.el7_8.noarch.rpm 298ad8b5602c5d19fe31a1ce894f086a3791109c72e8639696d1f86764844948 git-gnome-keyring-1.8.3.1-22.el7_8.x86_64.rpm 7d3e2c231fd82b2391c02dcc67fbfbecb2611fff1ff71d8ee4afcfc754c77581 git-gui-1.8.3.1-22.el7_8.noarch.rpm e2564d303ab9591bf676e2b648962b129494d6cde44fc07cbf35876f7bae6cbc git-hg-1.8.3.1-22.el7_8.noarch.rpm 937e2b3ae022aa61e8f940621deada7b91acab68b8a5d8cf110ab7db2627b168 git-instaweb-1.8.3.1-22.el7_8.noarch.rpm 06e30621b84c138fb4526ab8db767cfbd2a0e27347d31dff51de282b2e28c0f7 gitk-1.8.3.1-22.el7_8.noarch.rpm 002b73881adce7c1097c6eacae3126bbc5a8291bcae3287bfd5c6ebd54d3df8a git-p4-1.8.3.1-22.el7_8.noarch.rpm 06e66cad08604adc984297c26d16efdcdcf5eb24681f34617e602fcdf7d73f42 git-svn-1.8.3.1-22.el7_8.x86_64.rpm 017ae64401d8a4f4feafa909d3272c0c7b56f3985c433ce57983d646bd395e24 gitweb-1.8.3.1-22.el7_8.noarch.rpm d0f32f152e8d5c3f34d79a3eeda56968f86bf1b1cc988434d38f2850aed31cc7 perl-Git-1.8.3.1-22.el7_8.noarch.rpm 5c84268f2a7aa825566a1384008c11015782982fc09c403544758a6334021196 perl-Git-SVN-1.8.3.1-22.el7_8.noarch.rpm Source: a422d7a3c2620fbcde288f89eb7a7ef0f85d16355766e5914648ce75372f3cb9 git-1.8.3.1-22.el7_8.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Message: 6 Date: Thu, 30 Apr 2020 19:55:14 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CESA-2020:1561 Important CentOS 7 python-twisted-web Security Update Message-ID: <20200430195514.GA25077(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Security Advisory 2020:1561 Important Upstream details at : https://access.redhat.com/errata/RHSA-2020:1561 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: c934c963bfda9541fb295807dd5b3491516e30ddca030f9994b16aaf5abf586a python-twisted-web-12.1.0-7.el7_8.x86_64.rpm Source: 1fc7a67cae437978a930e1430f7fd6723180dfe327b2c173719b352e471804ab python-twisted-web-12.1.0-7.el7_8.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Message: 7 Date: Thu, 30 Apr 2020 19:57:02 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CESA-2020:1489 Important CentOS 7 thunderbird Security Update Message-ID: <20200430195702.GA25220(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Security Advisory 2020:1489 Important Upstream details at : https://access.redhat.com/errata/RHSA-2020:1489 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) x86_64: c1f729bd646d786b455ced02fdef3ba707209d19abbe2e9248afe1d5a9d619e4 thunderbird-68.7.0-1.el7.centos.x86_64.rpm Source: 089d5be107c79b4090a94a85a7eb10266faa859fe4a4cac0ef4dbd418f1946f8 thunderbird-68.7.0-1.el7.centos.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Message: 8 Date: Thu, 30 Apr 2020 19:58:15 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CESA-2020:1962 Important CentOS 6 python-twisted-web Security Update Message-ID: <20200430195815.GA25401(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Security Advisory 2020:1962 Important Upstream details at : https://access.redhat.com/errata/RHSA-2020:1962 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) i386: e5325be26650ca5a0802a3b95cb74026f32994e65aa2bd47c8d2ee33f639012d python-twisted-web-8.2.0-6.el6_10.i686.rpm x86_64: d9ae88251c4f8c24ce973b48536a2a12fe5cc447f2fdf868255072bf0f444014 python-twisted-web-8.2.0-6.el6_10.x86_64.rpm Source: 79f6182719d97f904c01fc56312ed76942e6a487e4d255854d8d8a4bcd07ec86 python-twisted-web-8.2.0-6.el6_10.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Message: 9 Date: Thu, 30 Apr 2020 19:58:47 +0000 From: Johnny Hughes <johnny(a)centos.org> To: centos-announce(a)centos.org Subject: [CentOS-announce] CEBA-2020:1982 CentOS 6 tzdata BugFix Update Message-ID: <20200430195847.GA25560(a)bstore1.rdu2.centos.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Bugfix Advisory 2020:1982 Upstream details at : https://access.redhat.com/errata/RHBA-2020:1982 The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) i386: 40bd5ea9365a4b62cf62983819ffbfc0b3cf796bb73c84738476457e3dc9ca8c tzdata-2020a-1.el6.noarch.rpm 35cc464cff218e7bd57f1f0583ec6f5f6228348d5dfa8cf319f2965b86685499 tzdata-java-2020a-1.el6.noarch.rpm x86_64: 40bd5ea9365a4b62cf62983819ffbfc0b3cf796bb73c84738476457e3dc9ca8c tzdata-2020a-1.el6.noarch.rpm 35cc464cff218e7bd57f1f0583ec6f5f6228348d5dfa8cf319f2965b86685499 tzdata-java-2020a-1.el6.noarch.rpm Source: 4e839c9ed8072332b875d17f7d54305a938996f3304808adafb0f455627adf13 tzdata-2020a-1.el6.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net Twitter: @JohnnyCentOS ------------------------------ Subject: Digest Footer _______________________________________________ CentOS-announce mailing list CentOS-announce(a)centos.org https://lists.centos.org/mailman/listinfo/centos-announce ------------------------------ End of CentOS-announce Digest, Vol 183, Issue 1 ***********************************************

1 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss May 2020