Discuss

discuss@lists.centos.org

2 participants
34758 discussions

Hard Drive Errors
by James Gagnon 20 Jan '06

20 Jan '06

Heya, First post to this list. have to say from what I have read in the passed couple months. damn you people are knowledgeable in this stuff! Anyways, I just setup a centos box for my personal little server at home. Basically just a small personal, non-corporate server that runs a webserver, DNS server, MySQL, and recently I installed webmin. The other night I took a peak through webmin to see what kind of things you could do with it and came across this Smart Drive option. Upon further investigation this option appears to show information about my hard drive as the Maxtor drives I have in my server have smart drive capability. They are just a standard IDE drive nothing fancy. When looking at this report I noticed a field called Errors and my Drive had 200 errors. What does this mean? Errors are usually not a good thing. is this a cause for concern? Is there any drive utility tools out there that fix these errors? Server seems to run fine. so I don't know what to think about these errors. That's on my main drive. My other backup drive has about 10,000 errors on it and that causes me some concern heh. Location IDE device A Drive size 29 GB Make and model Maxtor 6E030L0 Supports SMART? Yes SMART enabled? Yes Errors logged 300 errors detected Passed drive check? Yes Should I be concerned about these errors even though it does say it passed the drive check? If so, anyone know how I can fix them? Or is this just normal hard drive life? Any info would be great. Thanks! - James

4 7

Re: jnettop
by Peter Farrow 20 Jan '06

20 Jan '06

I think Jnettop was an adaption of the original nettop, but I am not sure... P. Andrew Rice wrote: >wow this program is utterly pimp!! > > > > >

1 0

'root' ssh login
by Tom Brown 20 Jan '06

20 Jan '06

how can i stop root logging into ssh ? I presume there is a setup file somewhere? thanks

10 10

RE: [CentOS] RE: Broadcom NIC Binding under Centos 4.2
by ABOKHALAF, Nassri Abdellatif 20 Jan '06

20 Jan '06

Ethernet Channel Bonding Driver: v2.6.1 (October 29, 2004) Bonding Mode: fault-tolerance (active-backup) Primary Slave: None Currently Active Slave: eth0 MII Status: up MII Polling Interval (ms): 100 Up Delay (ms): 0 Down Delay (ms): 0 Slave Interface: eth0 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:15:60:ad:a0:8a Slave Interface: eth1 MII Status: up Link Failure Count: 0 Permanent HW addr: 00:15:60:ad:a0:89 > show me your modprobe.conf /etc/modprobe.conf alias vlan 8021q alias bond0 bonding options bonding miimon=100 mode=1 alias eth0 tg3 alias eth1 tg3 alias scsi_hostadapter cciss alias usb-controller ehci-hcd alias usb-controller1 uhci-hcd alias net-pf-10 off /etc/sysconfig/network NETWORKING=yes HOSTNAME=dns.refertelecom.pt GATEWAY=10.192.32.254 GATEWAYDEV=bond0.201 eth0 DEVICE=eth0 BOOTPROTO=static TYPE=Ethernet ONBOOT=yes SLAVE=yes MASTER=bond0 eth1 DEVICE=eth1 BOOTPROTO=static TYPE=Ethernet ONBOOT=yes SLAVE=yes MASTER=bond0 bond0.201 DEVICE=bond0.201 ONBOOT=yes IPADDR=10.192.32.37 NETMASK=255.255.255.0 bond0 DEVICE=bond0 ONBOOT=yes Regards, Nassri

2 2

CentOS 3.6 won't poweroff
by Adrian Coman 20 Jan '06

20 Jan '06

Hi, I have a Packard Bell notebook with CentOS 3.6 installed. When I want to turn off the computer everything goes OK until the power should be switched off ... but the display remains turned on with the last "power down" message on it .. until I press the button. Is there a fix for this? The kernel is 2.4.21-37.EL . Thanks, Adrian

2 1

RHDS on Centos 4.2
by Ioannis Vranos 20 Jan '06

20 Jan '06

Is Red Hat Developer Studio (RHDS 2.1) available for CentOS 4.2? If yes, where may I download it? Thank you in advance.

4 5

RE: [CentOS] RE: Broadcom NIC Binding under Centos 4.2
by ABOKHALAF, Nassri Abdellatif 20 Jan '06

20 Jan '06

Thanks for your reply Robin, > It looks like you switch is configured to use tagged vlans. I must use tagged vlans. I configured the switch as your example. > Then add the following config file. >/etc/sysconfig/network-scripts/ifcfg-bond0.201 >DEVICE=bond0.201 I cannot bring this interface up. If you do ifconfig it only shows bond0, eth0 & eth1. Since bond0.201 does not come up, the system has no default gateway. Any clue? Nassri

2 1

recompiling kernel for centos 4.2 x86_64
by Fong Vang 20 Jan '06

20 Jan '06

Is it possible compile an a new x86_64 kernel on an i686 CentOS system? When I tried to do so with this command rpmbuild -ba --target x86_64 kernel-2.6.spec I got the following error: make[1]: *** [nonint_oldconfig] Error 51 make: *** [nonint_oldconfig] Error 2 error: Bad exit status from /var/tmp/rpm-tmp.40130 (%build) RPM build errors: Bad exit status from /var/tmp/rpm-tmp.40130 (%build) Isn't gcc able to do cross compile?

8 24

CentOS-announce Digest, Vol 11, Issue 8
by centos-announce-request＠centos.org 20 Jan '06

20 Jan '06

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CESA-2006:0160 Moderate CentOS 4 x86_64 tetex - security update (Johnny Hughes) 2. CESA-2006:0160 Moderate CentOS 4 i386 tetex - security update (Johnny Hughes) 3. CESA-2006:0184 Critical CentOS 4 i386 kdelibs - security update (Johnny Hughes) 4. CESA-2006:0184 Critical CentOS 4 x86_64 kdelibs - security update (Johnny Hughes) 5. CESA-2006:0140 Important CentOS 3 i386 kernel - security update (Tru Huynh) 6. CESA-2006:0140 Important CentOS 3 x86_64 kernel - security update (Tru Huynh) 7. CESA-2006:0160 Moderate CentOS 3 i386 tetex - security update (Tru Huynh) 8. CESA-2006:0160 Moderate CentOS 3 x86_64 tetex - security update (Tru Huynh) 9. CESA-2006:0140 Important CentOS 3 ia64 kernel - security update (Pasi Pirhonen) 10. CESA-2006:0160 Moderate CentOS 3 ia64 tetex - security update (Pasi Pirhonen) 11. CESA-2006:0160 Moderate CentOS 4 ia64 tetex - security update (Pasi Pirhonen) 12. CESA-2006:0184 Critical CentOS 4 ia64 kdelibs - security update (Pasi Pirhonen) 13. CESA-2006:0184 Critical CentOS 4 axp kdelibs - security update (Pasi Pirhonen) 14. CESA-2006:0160 Moderate CentOS 4 axp tetex - security update (Pasi Pirhonen) ---------------------------------------------------------------------- Message: 1 Date: Thu, 19 Jan 2006 15:19:14 -0600 From: Johnny Hughes <johnny(a)centos.org> Subject: [CentOS-announce] CESA-2006:0160 Moderate CentOS 4 x86_64 tetex - security update To: CentOS-Announce <centos-announce(a)centos.org> Message-ID: <1137705554.13893.46.camel(a)myth.home.local> Content-Type: text/plain; charset="us-ascii" CentOS Errata and Security Advisory 2006:0160 https://rhn.redhat.com/errata/RHSA-2006-0160.html The following updated files have been uploaded and are currently syncing to the mirrors: x86_64: tetex-2.0.2-22.EL4.7.x86_64.rpm tetex-afm-2.0.2-22.EL4.7.x86_64.rpm tetex-doc-2.0.2-22.EL4.7.x86_64.rpm tetex-dvips-2.0.2-22.EL4.7.x86_64.rpm tetex-fonts-2.0.2-22.EL4.7.x86_64.rpm tetex-latex-2.0.2-22.EL4.7.x86_64.rpm tetex-xdvi-2.0.2-22.EL4.7.x86_64.rpm src: tetex-2.0.2-22.EL4.7.src.rpm

1 0

Booting off and installing from USB cdrom drive
by Taco Scargo 20 Jan '06

20 Jan '06

Hi all, I am trying to install CentOS from an external USB cdrom drive but am experiencing that anaconda does not recognize the device as cdrom device. Anyone have any experience with this and how to get it working ? After loading the appropriate usb-storage drivers the device is recognized and registered as /dev/sr0, but apparently that device is not checked or considered a cdrom device. Thanks, Taco

1 0

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss