Discuss

discuss@lists.centos.org

34758 discussions

Re: [CentOS] disk cloning ?
by hadi motamedi 11 Nov '13

11 Nov '13

On 11/11/13, Reindl Harald <h.reindl(a)thelounge.net> wrote: > > > Am 11.11.2013 11:52, schrieb hadi motamedi: >> On 11/11/13, Vishesh kumar <linuxtovishesh(a)gmail.com> wrote: >>> I think below command will serve your purpose. >>> >>> #dd if=/dev/sdb of=/dev/sdc conv=noerror,sync >>> >> Sorry. It quit with the following error : >> "no space left on device" >> What can I do next? > > buy a bigger target drive? > > > Sorry . Both are 40GB . Is it sufficient ?

1 0

Installing CentOS via USB thumbdrive
by Joseph Spenner 11 Nov '13

11 Nov '13

I've been poking at this for quite a while, and have never been able to get it to work. I've found a couple links with some partial truths: http://syslint.com/syslint/how-to-make-a-usb-boot-disk-for-centosrhel-from-… http://brakkee.org/site/2013/05/09/creating-a-usb-install-for-centos-6-4/ The first one talks about converting a standard iso to a 'hybrid' image, using: 'isohybrid'. But it then instructs the reader to make a vfat partition on the thumbdrive, and DD the image to that partition. This seemed odd to me, since the image itself should have all that info. I've used hybrid images before, such as Linux Mint, and was simply able to dd directly to the device itself, ie: dd if=/path/to/hybrid.iso of=/dev/sdb (where sdb is the thumbdrive). But, I went along with it, and it failed-- unable to find 'isolinux.bin'. I've read this error is due to old/incompatible firmware, but I've booted other thumbdrive hybrid-built images many times, and have never seen this except in CentOS installations. So, I tried doing a dd directly to the thumbdrive device, rather than the partition. This actually looked like it was going to work. I got to the initial installer page, and proceeded through the Language and Keyboard questions. It then forgot where itself was, and asked me where the media for installation was. I selected Hard Drive, and /dev/sda1 showed up as default. I hit enter, and it continued further. But then it again forgot where the media was, and couldn't find the installation media. The second URL/instruction wouldn't boot at all. Has anyone successfully installed via USB? I remember reading some multi part instructions where the USB drive is formatted with some special tools, often involving Windows, and various files need to be copied to the USB drive. But I was hoping we were passed that by now. But then again, Dell firmware updates still want me to make a DOS bootable floppy. So, I'm usually not surprised when I hear something like this. :) Thanks! Regards, Joseph Spenner If life gives you lemons, keep them-- because hey.. free lemons. "~heart~ Sticker" fixer: http://microflush.org/stuff/stickers/heartFix.html

5 6

how to calculate mail storage/traffic used
by Götz Reinicke - IT Koordinator 11 Nov '13

11 Nov '13

Hi, we have to setup a server which gets a copy of all messages send and received by our mailserver as a 1:1 copy. Mails send to multiple recipients should be calculated and saved per user. (great if you usually have lost of mails send to groups of people.) So no dedublication should be used here. (e.g. save the message and refer the different recipients to it.) How can I calculate the current traffic in the best way to extrapolate the amount of space to be planed for the new server? We think to have a couples of days to be saved. Thanks for any hint or comment. Regards Götz -- Götz Reinicke IT-Koordinator Tel. +49 7141 969 82 420 Fax +49 7141 969 55 420 E-Mail goetz.reinicke(a)filmakademie.de Filmakademie Baden-Württemberg GmbH Akademiehof 10 71638 Ludwigsburg www.filmakademie.de Eintragung Amtsgericht Stuttgart HRB 205016 Vorsitzender des Aufsichtsrats: Jürgen Walter MdL Staatssekretär im Ministerium für Wissenschaft, Forschung und Kunst Baden-Württemberg Geschäftsführer: Prof. Thomas Schadt

2 1

Strange unexplainable CUPS problem after upgrade to 5.10
by Robert Heller 10 Nov '13

10 Nov '13

I manage a bunch of workstations at the Wendell Free Library. They are all diskless, boot via PXE and mount all of their file systems via NFS from a server. All of the machines are 32-bit and run CentOS (fully up-to-date running 5.10). There are two printers with queues managed on the server. The server 'shares' these printers on the local LAN (eg with all of the workstations). After the upgrade to 5.10, *one* of the machine no longer sees the printers. *Nothing* is different about its configuration files, since these files are mounted via NFS from the server, *like all of the other workstations*. The other workstations all see the printers shared by the server. I don't understand what is going on here. And cannot find the problem. lpstat -t on the server yields: scheduler is running system default destination: BlackandWhiteLaserjet device for BlackandWhiteLaserjet: socket://192.168.1.246:9100 device for Officejet_Color: socket://192.168.1.253 BlackandWhiteLaserjet accepting requests since Tue 19 Jun 2012 03:27:17 PM EDT Officejet_Color accepting requests since Tue 24 Jul 2012 04:43:33 PM EDT printer BlackandWhiteLaserjet is idle. enabled since Tue 19 Jun 2012 03:27:17 PM EDT printer Officejet_Color is idle. enabled since Tue 24 Jul 2012 04:43:33 PM EDT lpstat -t on the bum workstation yields: lpstat: No destinations added. lpstat: No destinations added. lpstat: No destinations added. lpstat: No destinations added. scheduler is running no system default destination and lpstat -t on a working workstation yields: scheduler is running system default destination: BlackandWhiteLaserjet device for BlackandWhiteLaserjet: ipp://192.168.1.254:631/printers/BlackandWhiteLaserjet device for Officejet_Color: ipp://192.168.1.254:631/printers/Officejet_Color BlackandWhiteLaserjet accepting requests since Sun 10 Nov 2013 10:26:03 AM EST Officejet_Color accepting requests since Sun 10 Nov 2013 10:26:04 AM EST printer BlackandWhiteLaserjet is idle. enabled since Sun 10 Nov 2013 10:26:03 AM EST printer Officejet_Color is idle. enabled since Sun 10 Nov 2013 10:26:04 AM EST The server's /etc/cups/cupsd.conf looks like this: LogLevel debug2 SystemGroup sys root admin # Allow remote access Port 631 Listen /var/run/cups/cups.sock # Enable printer sharing and shared printers. Browsing On BrowseOrder allow,deny # (Change '@LOCAL' to 'ALL' if using directed broadcasts from another subnet.) BrowseAllow @LOCAL BrowseAddress @LOCAL DefaultAuthType Basic <Location /> # Allow shared printing and remote administration... Order allow,deny Allow all </Location> <Location /admin> Allow from localhost Allow from 192.168.1.27 Allow from 192.168.1.28 Allow from 192.168.1.29 Allow from 192.168.1.5 # Allow remote administration... Order allow,deny Allow all </Location> <Location /admin/conf> AuthType Basic Require user @SYSTEM Allow localhost # Allow remote access to the configuration files... Order allow,deny Allow all </Location> <Policy default> <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit Pause-Printer Resume-Printer Set-Printer-Attributes Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Add-Printer CUPS-Delete-Printer CUPS-Add-Class CUPS-Delete-Class CUPS-Accept-Jobs CUPS-Reject-Jobs CUPS-Set-Default> AuthType Basic Require user @SYSTEM Order deny,allow </Limit> <Limit CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> and the cupsd.conf (shared by ALL of the workstations) looks like this: # # "$Id: cupsd.conf.in 7199 2008-01-08 00:16:30Z mike $" # # Sample configuration file for the Common UNIX Printing System (CUPS) # scheduler. See "man cupsd.conf" for a complete description of this # file. # MaxLogSize 2000000000 # Log general information in error_log - change "info" to "debug" for # troubleshooting... LogLevel debug # Administrator user group... SystemGroup sys root # Allow remote access Port 631 Listen /var/run/cups/cups.sock # Only listen for connections from the local machine. #Listen localhost:631 #Listen /var/run/cups/cups.sock # Show shared printers on the local network. Browsing On BrowseOrder allow,deny # (Change '@LOCAL' to 'ALL' if using directed broadcasts from another subnet.) BrowseAllow @LOCAL BrowseAllow 192.168.1.27 BrowseAllow 192.168.1.28 BrowseAllow 192.168.1.29 BrowseAllow 192.168.1.5 BrowseAllow 192.168.1.254 BrowseAllow 10.163.1 BrowseAddress @LOCAL # Default authentication type, when authentication is required... DefaultAuthType Basic # Restrict access to the server... <Location /> Order allow,deny Allow localhost Allow from 192.168.1.27 Allow from 192.168.1.28 Allow from 192.168.1.29 Allow from 192.168.1.5 Allow from 192.168.1.254 Allow from 10.163.1 </Location> # Restrict access to the admin pages... <Location /admin> Order allow,deny Allow localhost Allow from 192.168.1.27 Allow from 192.168.1.28 Allow from 192.168.1.29 Allow from 192.168.1.5 Allow from 192.168.1.254 </Location> # Restrict access to configuration files... <Location /admin/conf> AuthType Default Require user @SYSTEM Order allow,deny </Location> # Set the default printer/job policies... <Policy default> # Job-related operations must be done by the owner or an administrator... <Limit Send-Document Send-URI Hold-Job Release-Job Restart-Job Purge-Jobs Set-Job-Attributes Create-Job-Subscription Renew-Subscription Cancel-Subscription Get-Notifications Reprocess-Job Cancel-Current-Job Suspend-Current-Job Resume-Job CUPS-Move-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> # All administration operations require an administrator to authenticate... <Limit CUPS-Add-Modify-Printer CUPS-Delete-Printer CUPS-Add-Modify-Class CUPS-Delete-Class CUPS-Set-Default> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # All printer operations require a printer operator to authenticate... <Limit Pause-Printer Resume-Printer Enable-Printer Disable-Printer Pause-Printer-After-Current-Job Hold-New-Jobs Release-Held-New-Jobs Deactivate-Printer Activate-Printer Restart-Printer Shutdown-Printer Startup-Printer Promote-Job Schedule-Job-After CUPS-Accept-Jobs CUPS-Reject-Jobs> AuthType Default Require user @SYSTEM Order deny,allow </Limit> # Only the owner or an administrator can cancel or authenticate a job... <Limit Cancel-Job CUPS-Authenticate-Job> Require user @OWNER @SYSTEM Order deny,allow </Limit> <Limit All> Order deny,allow </Limit> </Policy> # # End of "$Id: cupsd.conf.in 7199 2008-01-08 00:16:30Z mike $". # -- Robert Heller -- 978-544-6933 / heller(a)deepsoft.com Deepwoods Software -- http://www.deepsoft.com/ () ascii ribbon campaign -- against html e-mail /\ www.asciiribbon.org -- against proprietary attachments

2 1

logical volume and drive names after mirroring a centos installation via rsync
by Peter Peltonen 10 Nov '13

10 Nov '13

I have a working CentOS5 installation on server A's first SATA drive (sda). I had an empty SATA drive on that server (sdb). I was asked to mirror the installation of server B (installed on first SATA drive, sda), also running CentOS5, to the second drive (sdb) of server A. I am unsure what should be done after mirroring to get the new system boot. What I have done already: - On server A/sdb I created the same partition layout and a little bit bigger logical volumes as on server B/sda plus created the filesystems (130G / fs and 200M /boot fs). The volume group and logical volumes have different names. I have mounted the new volumes on server A. - From server B/sda I rsynced all data to server A/sdb (excluding /dev/*,/proc/*,/sys/*,/tmp/*,/run/*,/mnt/*,/media/*,/lost+found) whitle most services were stopped on server B Now I would need to figure out how to boot to the CentOS installation on server A/sdb and I would like to ask about a few details: - I am confused about the logical volume names: which ones should I use on the new server's fstab, the old ones (rsynced from server B/sda) or the ones I used when creating the logical volumes from server A? If I need to use the new ones, should I update the names also somewhere else than fstab? - As the new installation will boot from sdb instead of sda, do I need to update this information somewhere (like /boot/grub/device.map) ? - How do I install grub on the second drive? Do I simply command from the A/sda installation: grub-install /dev/sdb ? - And to access this new grub I just mark the second drive as the boot drive in BIOS and boot, yes? - If I also wanted to boot to the new A/sdb system by using the grub in A/sda installation, what should the entry in /boot/grub/menu.lst look like, do I just change the hd(0,0) parameter to hd(1,0) and edit correct kernel and initrd values? Regards, Peter

3 4

Install to internal USB?
by Lists 10 Nov '13

10 Nov '13

Saw a trick today, wondering if anybody else had done/tried this? Assume you have a 1U rackmount with 4 front-accessed drive bays, and you want all four bays for a 4-disk RAID5 storage. The idea is to use an internal USB adapter and a couple of bigger USB thumb drives to install to, RAID 1 style, freeing up all your external drive bays. At first, I didn't think that a thumb drive would hold enough for the O/S, but in actual production use for a file server with 14 TB of redundant storage, the OS actually uses less than 6 GB! Here's the internal USB adapter specifically mentioned: http://www.amazon.com/gp/product/B007PODI1W I'd be concerned about getting a higher quality drive than the $10 givaways at Staples; Anybody here ever tried this?

6 12

Wireless problems
by Krzysztof Szarlej 09 Nov '13

09 Nov '13

Hi guys, I have a problem with my Centos 6.4. I am experiencing a Wireless Disconnects, some time ago I had them constantly each 2-3minutes. After upgrading to new kernel (and other software from "Software Update" I am still exepriencing disconnects but every 10-15 minutes. It makes me angry because I am doing a lot of work with ftp servers. Card: *Atheros Communications Inc. AR9285 Wireless Network Adapter (PCI-Express) (rev 01)* uname -r: *2.6.32-358.23.2.el6.i686* I Turned off ipv6 in */etc/sysctl.conf* Here is Log: ( I divided it into 2 stages) ---------------------------------------------------- Nov 8 14:10:01 mlody kernel: cfg80211: Calling CRDA to update world regulatory domain Nov 8 14:10:01 mlody NetworkManager[8817]: <info> (wlan0): supplicant connection state: completed -> disconnected Nov 8 14:10:01 mlody kernel: cfg80211: World regulatory domain updated: Nov 8 14:10:01 mlody kernel: cfg80211: (start_freq - end_freq @ bandwidth), (max_antenna_gain, max_eirp) Nov 8 14:10:01 mlody kernel: cfg80211: (2402000 KHz - 2472000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Nov 8 14:10:01 mlody kernel: cfg80211: (2457000 KHz - 2482000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Nov 8 14:10:01 mlody kernel: cfg80211: (2474000 KHz - 2494000 KHz @ 20000 KHz), (300 mBi, 2000 mBm) Nov 8 14:10:01 mlody kernel: cfg80211: (5170000 KHz - 5250000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) Nov 8 14:10:01 mlody kernel: cfg80211: (5735000 KHz - 5835000 KHz @ 40000 KHz), (300 mBi, 2000 mBm) ------------------------------------------------------- Nov 8 14:10:01 mlody NetworkManager[8817]: <info> (wlan0): supplicant connection state: disconnected -> scanning Nov 8 14:10:17 mlody NetworkManager[8817]: <info> (wlan0): device state change: 8 -> 3 (reason 11) Nov 8 14:10:17 mlody NetworkManager[8817]: <info> (wlan0): deactivating device (reason: 11). Nov 8 14:10:17 mlody NetworkManager[8817]: <info> (wlan0): canceled DHCP transaction, DHCP client pid 16791 Nov 8 14:10:17 mlody NetworkManager[8817]: <warn> Couldn't disconnect supplicant interface: Method "Disconnect" with signature "" on interface "fi.epitest.hostap.WPASupplicant.Interface" doesn't exist#012. Nov 8 14:10:17 mlody NetworkManager[8817]: <info> Auto-activating connection 'Auto Bulgarski Poscikk'. Nov 8 14:10:17 mlody NetworkManager[8817]: <info> Activation (wlan0) starting connection 'Auto Bulgarski Poscikk' ... first block: This appears and after several seconds then second block appear and the wifi is disconnected, right after it disconnects it tries to reconnect. *Regards!*

2 3

IBM Storwize V3700 storage - device names
by Todor Petkov 08 Nov '13

08 Nov '13

Hello, I have IBM Storwize V3700 storage, connected to 2 IBM x3550 M4 servers via fiber channel. The servers are with QLogic ISP2532-based 8Gb Fibre Channel to PCI Express HBA cards and run Centos 5.10 When I export a volume to the servers, each of them sees the volume twice, i.e /dev/sdb and /dev/sdc, with the same size. Previously I have installed many systems with IBM DS3500 series of storage and the servers see one disk per export. I am using the MPP drives from this package: http://support.netapp.com/NOW/public/apbu/oemcp/apbu_lic.cgi/public/apbu/oe… I came upon the IBM site, saying to configure multipath (I never did it for DS3500 series). When I did, a new device came, /dev/dm-7, but my goal is to have one /dev/sdX type of device and no device mapper. I read that Storwize support DMP RDAC, and DS support MPP RDAC, but does anyone else have experience with such setup and can give an advice/hint? Thanks in advance.

2 1

CentOS-announce Digest, Vol 105, Issue 6
by centos-announce-request＠centos.org 08 Nov '13

08 Nov '13

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CEBA-2013:1506 CentOS 6 udev Update (Johnny Hughes) ---------------------------------------------------------------------- Message: 1 Date: Thu, 7 Nov 2013 15:26:14 +0000 From: Johnny Hughes <johnny(a)centos.org> Subject: [CentOS-announce] CEBA-2013:1506 CentOS 6 udev Update To: centos-announce(a)centos.org Message-ID: <20131107152614.GA51912(a)n04.lon1.karan.org> Content-Type: text/plain; charset=us-ascii CentOS Errata and Bugfix Advisory 2013:1506 Upstream details at : https://rhn.redhat.com/errata/RHBA-2013-1506.html The following updated files have been uploaded and are currently syncing to the mirrors: ( sha256sum Filename ) i386: b037d6c2c622f7a34fa0765e4bfd64cd1859207946dbb2c81b31b1c023474a3c libgudev1-147-2.46.el6_4.2.i686.rpm 6188b3eb42bf874d8a246e06511bfa799caf7b1cf3ea61daa8512a564dfa91df libgudev1-devel-147-2.46.el6_4.2.i686.rpm 6918e179150b87608ca4afdfaca40cb81d252d82d4d5782a842ea16b2f922525 libudev-147-2.46.el6_4.2.i686.rpm b543f81d1516650b23013a477bbb2b4c88e87f7126fda4476acae8ce84ebae0e libudev-devel-147-2.46.el6_4.2.i686.rpm aece91f7bda8f95d7596555acbc7b7d629ca8463cf3cb0a70b3a9159537bc4a8 udev-147-2.46.el6_4.2.i686.rpm x86_64: b037d6c2c622f7a34fa0765e4bfd64cd1859207946dbb2c81b31b1c023474a3c libgudev1-147-2.46.el6_4.2.i686.rpm 6a537fc17943a2e2bfa28404545b02aa4e87fc4d383c76be9c493bda75f32f8c libgudev1-147-2.46.el6_4.2.x86_64.rpm 6188b3eb42bf874d8a246e06511bfa799caf7b1cf3ea61daa8512a564dfa91df libgudev1-devel-147-2.46.el6_4.2.i686.rpm 343a8ca5cc5f4230119d68610b65f1994b5f2a79b58930fdb42bd9911c8a75e8 libgudev1-devel-147-2.46.el6_4.2.x86_64.rpm 6918e179150b87608ca4afdfaca40cb81d252d82d4d5782a842ea16b2f922525 libudev-147-2.46.el6_4.2.i686.rpm f6775e18c55f77726482388648ce5acb30084399ab9f1a84392ed728b2208137 libudev-147-2.46.el6_4.2.x86_64.rpm b543f81d1516650b23013a477bbb2b4c88e87f7126fda4476acae8ce84ebae0e libudev-devel-147-2.46.el6_4.2.i686.rpm cc89b8410bbc8061c0c66d320793dbe6be8f0bc85759099513663c5ed066bda3 libudev-devel-147-2.46.el6_4.2.x86_64.rpm 5d95c1d1a19cf7e6b3b7be132a95c6a780047bb8b3b216e00012759c522502ec udev-147-2.46.el6_4.2.x86_64.rpm Source: a85a5c251c89d8ac6810a7316d0da6980d4cc864b0cad57a59d0ee042b6c4fcf udev-147-2.46.el6_4.2.src.rpm -- Johnny Hughes CentOS Project { http://www.centos.org/ } irc: hughesjr, #centos(a)irc.freenode.net ------------------------------ _______________________________________________ CentOS-announce mailing list CentOS-announce(a)centos.org http://lists.centos.org/mailman/listinfo/centos-announce End of CentOS-announce Digest, Vol 105, Issue 6 ***********************************************

1 0

chipsets etc to avoid for CentOS 6.x
by Devin Reade 08 Nov '13

08 Nov '13

It's time to purchase hardware again, and I'm going through the usual "of that which is on the market, what will CentOS run without leaving new hardware collecting dust for a year"? I'm looking at a number of commodity-grade machines (ie: desktop grade will suffice) with reasonably fast CPUs and able to use at least 8GB each (preferably 32GB). These will be deployed as software development systems in run mode 3 (ie: no real graphical requirement). Does anyone have suggestions, assuming a CentOS 6.x install, what CPUs/chipsets, etc, to avoid? (Or alternately, which ones still commonly on the market are fine?) I've typically stuck to Intel CPUs, and prefer Gigabyte or Intel motherboards. I'd prefer to minimize the likelihood of non-working or marginally-working hardware. I've had a look at the supported RHEL hardware list, but they typically just list Xeon-based machines. Thanks in advance. Devin

3 3

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss