- Discuss - lists.centos.org

ACPI errors during bootup
by sri 23 Mar '11

23 Mar '11

Hi, Am trying to build SMP kernel. Took kernel-2.6.18-194.src.rpm, extracted, rpmbuilded with SMP option. Successfully compile the new kernel and when using that kernel to boot up, following errors were shown up(highlighted in bold & red color): My kernel config file has ACPI and PCI configs enabled. Any pointers to what caused the problem are appreciated. ****************************** ********************************************************************************* BIOS-e820: 0000000000010000 - 000000000009e000 (usable) BIOS-e820: 000000000009e000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e0000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 000000001fee9000 (usable) BIOS-e820: 000000001fee9000 - 0000000020000000 (reserved) BIOS-e820: 00000000fff00000 - 0000000100000000 (reserved) 0MB HIGHMEM available. 510MB LOWMEM available. Memory for crash kernel (0x0 to 0x0) notwithin permissible range disabling kdump Using x86 segment limits to approximate NX protection DMI not present or invalid. Using APIC driver default ACPI: Unable to locate RSDP Allocating PCI resources starting at 30000000 (gap: 20000000:dff00000) Detected 1000.103 MHz processor. Built 1 zonelists. Total pages: 130793 Kernel command line: root=/dev/ram ramdisk_size=200000 ramdisk_start=0x6000000 c onsole=ttyS0,9600n8 plat=bryce reboot=warm n Local APIC disabled by BIOS -- you can enable it with "lapic" Enabling fast FPU save and restore... done. Enabling unmasked SIMD FPU exception support... done. Initializing CPU#0 CPU 0 irqstacks, hard=c076f000 soft=c074f000 PID hash table entries: 2048 (order: 11, 8192 bytes) Console: colour dummy device 80x25 Dentry cache hash table entries: 65536 (order: 6, 262144 bytes) Inode-cache hash table entries: 32768 (order: 5, 131072 bytes) Memory: 503320k/523172k available (2189k kernel code, 19224k reserved, 920k data , 232k init, 0k highmem) Checking if this processor honours the WP bit even in supervisor mode... Ok. Calibrating delay loop (skipped), value calculated using timer frequency.. 2000. 20 BogoMIPS (lpj=1000103) Security Framework v1.0.0 initialized SELinux: Initializing. selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 512 CPU: L1 I cache: 32K, L1 D cache: 32K CPU: L2 cache: 512K Intel machine check architecture supported. Intel machine check reporting enabled on CPU#0. Checking 'hlt' instruction... OK. SMP alternatives: switching to UP code Freeing SMP alternatives: 14k freed CPU0: Intel(R) Celeron(R) M processor 1.00GHz stepping 08 SMP motherboard not detected. Local APIC not detected. Using dummy APIC emulation. Brought up 1 CPUs *checking if image is initramfs... it is Freeing initrd memory: 10554k freed NET: Registered protocol family 16 PCI: PCI BIOS revision 2.10 entry at 0xff67f, last bus=4 PCI: Using configuration type 1 Setting up standard PCI resources ACPI: Interpreter disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI: disabled usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Probing PCI hardware ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found PCI quirk: region 1000-107f claimed by ICH4 ACPI/GPIO/TCO PCI quirk: region 0500-053f claimed by ICH4 GPIO ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found PCI: Ignoring BAR0-3 of IDE controller 0000:00:1f.2 ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found ACPI Error (tbxfroot-0645): No valid RSDP was found [20060707] ACPI Exception (tbxfroot-0400): AE_NOT_FOUND, RSDP structure not found - Flags=8 [20060707] ACPI: System description tables not found* PCI: Transparent bridge - 0000:00:1e.0 NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default PCI: Bridge: 0000:00:02.0 IO window: c000-0000 MEM window: c0100000-00000000 PREFETCH window: disabled. PCI: Bridge: 0000:00:03.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1c.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Bridge: 0000:00:1e.0 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: No IRQ known for interrupt pin A of device 0000:00:02.0. Please try using p ci=biosirq. PCI: No IRQ known for interrupt pin A of device 0000:00:03.0. Please try using p ci=biosirq. NET: Registered protocol family 2 IP route cache hash table entries: 4096 (order: 2, 16384 bytes) TCP established hash table entries: 16384 (order: 5, 131072 bytes) TCP bind hash table entries: 8192 (order: 4, 65536 bytes) TCP: Hash tables configured (established 16384 bind 8192) TCP reno registered apm: BIOS not found. audit: initializing netlink socket (disabled) type=2000 audit(1300527457.278:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 1024 (order 0, 4096 bytes) Initializing Cryptographic API alg: No test for crc32c (crc32c-generic) ksign: Installing public key data Loading keyring io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) pcieport-driver 0000:00:02.0: device [8086:3595] has invalid IRQ; check vendor B IOS pcieport-driver 0000:00:03.0: device [8086:3596] has invalid IRQ; check vendor B IOS pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ************************************************************************************************************************** -- -- Krishna Mohan B -- -- Krishna Mohan B

4 3

how can we help? was: Re: The delays on CentOS 5.6 are causing EPEL incompatibilities
by cornel panceac 23 Mar '11

23 Mar '11

2011/3/23 R P Herrold <herrold(a)owlriver.com> > This comes and goes, and really there is no substitute for actually > 'doing' rather than > talking in the cloister > > as i see it, the problem is while the users expectation has grown, the work became harder. so i believe the real question is: how can we help the CentOS project? how can we unload the developers so that they do more high level and/or creative things with less work?

2 1

CentOS-announce Digest, Vol 73, Issue 4
by centos-announce-request＠centos.org 23 Mar '11

23 Mar '11

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CESA-2011:0370 Moderate CentOS 4 x86_64 wireshark - security update (Johnny Hughes) 2. CESA-2011:0370 Moderate CentOS 4 i386 wireshark - security update (Johnny Hughes) ---------------------------------------------------------------------- Message: 1 Date: Tue, 22 Mar 2011 16:47:45 -0500 From: Johnny Hughes <johnny(a)centos.org> Subject: [CentOS-announce] CESA-2011:0370 Moderate CentOS 4 x86_64 wireshark - security update To: CentOS-Announce <centos-announce(a)centos.org> Message-ID: <4D891901.8050602(a)centos.org> Content-Type: text/plain; charset="iso-8859-1" CentOS Errata and Security Advisory CESA-2011:0370 wireshark security update for CentOS 4 x86_64: https://rhn.redhat.com/errata/RHSA-2011-0370.html The following updated files have been uploaded and are currently syncing to the mirrors: x86_64: wireshark-1.0.15-2.el4.x86_64.rpm wireshark-gnome-1.0.15-2.el4.x86_64.rpm src: wireshark-1.0.15-2.el4.src.rpm

1 0

Duplicate Mails
by Ralph Angenendt 23 Mar '11

23 Mar '11

Hi, due to some idiot not being able to configure his Exchange server correctly, this list has been swamped by loads of duplicate mails. There were still several hundreds of mails awaiting delivery to this list. I have removed all of those from the mail queue - so if you are missing a mail you have sent, please resubmit it, it probably was lost while I cleaned the queue as I had no way of telling those apart from the reinjections. I am sorry that I had to do that, but I am sure that you'd rather resubmit than receiving close to 1000 duplicate mails. The user reinjecting the mails has been identified and shot^Wbanned from the mailing list, he cannot resubscribe. Apologies if this caused any inconveniences. Regards, Ralph Angenendt

8 7

EXT4 Filesystem Mount Failed (bad geometry: block count)
by Balaji 23 Mar '11

23 Mar '11

Dear All, Currently using RHEL6 Linux and Kernel Version is 2.6.32-71.el6.i686 and DRBD Version is 8.3.10 DRBD is build from source and Configured DRBD with 2 Node testing with Simplex Setup Server 1 : 192.168.13.131 IP Address and hostname is primary Server 2 : 192.168.13.132 IP Address and hostname is secondary Finally found that drbd0, drbd1 mount failed problem *Found some error messages in "dmesg"* block drbd0: role( Secondary -> Primary ) block drbd1: role( Secondary -> Primary ) EXT4-fs (drbd0): bad geometry: block count 5242880 exceeds size of device (5242711 blocks) EXT4-fs (drbd1): bad geometry: block count 2621440 exceeds size of device (2621351 blocks) The drbd is working fine and is output as below [root@primary ~]# cat /proc/drbd version: 8.3.10 (api:88/proto:86-96) GIT-hash: 5c0b0469666682443d4785d90a2c603378f9017b build byroot(a)primary.mydomain.com, 2011-03-22 11:27:11 0: cs:WFConnection ro:Primary/Unknown ds:UpToDate/DUnknown C r----s ns:0 nr:0 dw:0 dr:677 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:20970844 1: cs:WFConnection ro:Primary/Unknown ds:UpToDate/DUnknown C r----s ns:0 nr:0 dw:0 dr:1009 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 ep:1 wo:b oos:10485404 [root@primary ~]# I have search and findout the same problem and its solved (links as below) http://lists.linbit.com/pipermail/drbd-user/2009-October/012812.html But in my case the problem is not solved (changed the meta-disk internal as flexible-meta-disk internal and tested) The same as working in ext3 filesystem and its not working in ext4 filesystem. Please find attached primary.zip file contains message log files and drbd configuration file for more analysis. I don't know what is the problem and Can some one throw light on this peculiar problem Please replay me ASAP. Thanks in Advance --Regards, S.Balaji

5 5

HP z3200ps printer ppd
by m.roth＠5-cent.us 22 Mar '11

22 Mar '11

Now that we've got the thing, does anyone know what ppd I can use for it? I've seen someone recommending: - the generic postscript ppd; - the hplips driver. I also see ppd's for a DesignJet 800ps, and ones for the 5000ps and 5500ps. Has anyone had any experience with any of these? mark

1 0

dns question
by ann kok 22 Mar '11

22 Mar '11

Hi all How can I know the refresh rate of the dns server? Thank you

3 2

Re: [CentOS] Affordable KVM over IP switch
by Nico Kadel-Garcia 22 Mar '11

22 Mar '11

On Tue, Mar 22, 2011 at 11:11 AM, Rudi Ahlers <Rudi(a)softdux.com> wrote: > On Tue, Mar 22, 2011 at 5:07 PM, Nico Kadel-Garcia <nkadel(a)gmail.com> wrote: >> On Tue, Mar 22, 2011 at 10:48 AM, Rudi Ahlers <Rudi(a)softdux.com> wrote: >>> On Tue, Mar 22, 2011 at 4:34 PM, Devin Reade <gdr(a)gno.org> wrote: >>>> Michael B Allen <ioplex(a)gmail.com> wrote: >>>> >>>>> Are there any KVM over IP switches that are not thousands of dollars? >>>>> Ideally a 3-4 port switch for a few hundred seems reasonable to me. >>>> >>>> I can attest that the Adderlink iPEPS and iPEPS-DA are excellent units. >>>> They're both in the 500-1000 range. They're intended for a single >>>> machine, but as long as your access policies allow for it, putting >>>> an electronic KVM switch (~$200) between multiple servers and the >>>> iPEPS works well. >>>> >>> >>> >>> >>> Isn't it cheaper, at this price range to get a motherboard with >>> built-in KVMOIP support? I know many Intel & SuperMicro server boards >>> offer this either on board, or as an added module. Even on the smaller >>> / cheaper SuperMicro boards I could add KVMOIP support for about $40 >>> per server. And, it doesn't takup any more space on the racks and has >>> much less clutter than those spiders >> >> Note. This is *NOT* CentOS, this is general systems discussion. >> >> That's great until you want to connect another session, or haven't had >> a chance to configure a new machine and want to do it remotely, or you >> want to leave your mom's netbook in the rack while you re-install it >> for her. (This just came up on another list.) >> _______________________________________________ > > True....... > > Both have their pro's & con's, but in our case we'll always only use > rackmount servers which is why I prefer the onboard modules. The overhead and instabilities of installing the components and configuring these features is adventuresome. Simply explaining to a client's inventory management that *they have to record the MAC addresses when they receive the hardware* so that the DHCP setups and network setups can be done gracefully has been awkward. For a few servers in a personal, or small business rack, it's not a big problem. But even the big hardware vendors can be very confusing to learn all the interface tricks and configurations for, and in a mixed environment it can get out of hand really, really fast. I've had a devil of a time demonstrating, and explaining to clients, why they need these tools, right up to the point when they say "but, but, but, I can do that with the Windows servers!!!!" and showing them, on the purchase orders and the emails, where they paid for that service and where they refused to allow me to install the drivers because that "wasn't part of the project". This has actually gotten *MUCH* better with "our favorite upstream verndor's" 6.0 operating system, and I'm looking forward to CentOS 6.0 with baited breath. The really cool features of IPMI have matured a lot, and in some cases no hardware vendor drivers are needed, It Just Works with the basic system installation. Unfortunately, I don't have a rack of hosts to test this on this week, or I'd suggest it.

1 0

Re: [CentOS] dns question
by aly.khimji＠gmail.com 22 Mar '11

22 Mar '11

What do you mean by refresh rate of the dns server? Like TTL length of records? Or..? Aly ------Original Message------ From: ann kok Sender: centos-bounces(a)centos.org To: centos(a)centos.org ReplyTo: CentOS mailing list Subject: [CentOS] dns question Sent: Mar 22, 2011 9:13 AM Hi all How can I know the refresh rate of the dns server? Thank you _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos Sent from my BlackBerry device on the Rogers Wireless Network

2 1

Need help in "repairing" the booting of my Linux 4 server
by Todd Cary 22 Mar '11

22 Mar '11

As I shared on this forum last week, I did a bad boo boo when I erased my /boot/ directory without a backup - all of the things I caution other NOT to do. Nevertheless, after trying to put things back in order, today I decided to try a reboot and I get a GRUB prompt. Next I have put my Linux 4 disk in the CD drive and have selected the "linux repair" mode which has put me into the /mnt/sysimage with the # prompt. That is as far as I have gone since I am in uncharted waters. Help! It, the linux repair, has found and identified that I have a Linux system...what should I try next? Todd -- Ariste Software Petaluma, CA 94952 http://www.aristesoftware.com

4 7

mdraid on top of mdraid
by Emmanuel Noobadmin 22 Mar '11

22 Mar '11

Is it possible or will there be any problems with using mdraid on top of mdraid? specifically say mdraid 1/5 on top of mdraid multipath. e.g. 4 storage machines exporting iSCSI targets via two different physical network switches then use multipath to create md block devices then use mdraid on these md block devices The purpose being the storage array surviving a physical network switch failure.

4 7

Re: [CentOS] mdraid on top of mdraid
by Emmanuel Noobadmin 21 Mar '11

21 Mar '11

> Since your exporting the storage as iSCSI, the host machine will see > it as a raw disk, irrespective of how it's setup on the exported > server. So, yes, you can do this. Sorry for my ambiguity, I meant that mdadm would be on the host machine. e.g. Using just a 2 node, raid 1 situation Storage 1 -> Disk exported on 192.168.1.10, 192.168.2.10 Storage 2 -> Disk exported on 192.168.1.20, 192.168.2.20 Host -> mdadm multipath md0 = 192.168.1.10, 192.168.2.10 -> mdadm multipath md1 = 192.168.1.20, 192.168.2.20 ---> mdadm raid 1 md2 using md0 md1

2 1

Admin stuff
by m.roth＠5-cent.us 21 Mar '11

21 Mar '11

Is there something odd going on? The question about the errors in mcelog just showed up *again*, and it's the original that I answered this morning. The question about something - was it the md? - original seems as though it's shown up more than twice today, with the same timestamp, I think. Is anyone else seeing this, or is it my host's mailserver? mark

6 5

Redelivery of 2 day old mail from this list?
by Jason Pyeron 21 Mar '11

21 Mar '11

Any ideas? This one would make the 10th email received. Return-Path: <centos-bounces(a)centos.org> Received: from psmtp.com (exprod8mx192.postini.com [64.18.3.171]) by mail.pdinc.us (8.12.11.20060308/8.12.11) with SMTP id p2LKkur4025229 for <jpyeron(a)pdinc.us>; Mon, 21 Mar 2011 16:46:57 -0400 Received: from source ([72.26.200.202]) by exprod8mx192.postini.com ([64.18.7.10]) with SMTP; Mon, 21 Mar 2011 16:46:31 EDT Received: from mail.centos.org (voxeldev.centos.org [127.0.0.1]) by mail.centos.org (Postfix) with ESMTP id 853916F841; Mon, 21 Mar 2011 16:38:54 -0400 (EDT) X-Original-To: centos(a)centos.org Delivered-To: centos(a)centos.org Received: from av-corp-esx01.SanJuan.Avalara.com (mail1.avalara.com [72.37.234.200]) by mail.centos.org (Postfix) with ESMTP id BE4F16F841 for <centos(a)centos.org>; Mon, 21 Mar 2011 16:38:52 -0400 (EDT) Received: from Pickup by av-corp-esx01.SanJuan.Avalara.com with Microsoft SMTP Server id 14.1.218.12; Sun, 20 Mar 2011 00:52:34 +0000 Message-ID: <4D854FF4.8020604(a)emmanuelcomputerconsulting.com> Date: Sat, 19 Mar 2011 20:53:08 -0400 From: William Warren <xxx@xxx> MIME-Version: 1.0 To: CentOS mailing list <centos(a)centos.org> References: <F27EEF0123414BCDA9D1EAC7FDD01214@phoenix> In-Reply-To: <F27EEF0123414BCDA9D1EAC7FDD01214@phoenix> Precedence: list X-Bayes-Prob: 0.0001 (Score 0, tokens from: @@RPTN) X-Spam-Score: 3.00 (***) [Hold at 10.00] 46(3) X-CanIt-Geo: ip=72.26.200.202; country=US; region=NY; city=New York; postalcode=10006; latitude=40.7082; longitude=-74.0132; metrocode=501; areacode=212; http://maps.google.com/maps?q=40.7082,-74.0132&z=6 X-CanItPRO-Stream: former.employees (inherits from default) X-Canit-Stats-ID: 01ElcP6k2 - 963888654722 X-Antispam-Training-Forget: http://10.30.31.25/canit/b.php?i=01ElcP6k2&m=963888654722&c=f X-Antispam-Training-Nonspam: http://10.30.31.25/canit/b.php?i=01ElcP6k2&m=963888654722&c=n X-Antispam-Training-Spam: http://10.30.31.25/canit/b.php?i=01ElcP6k2&m=963888654722&c=s X-Scanned-By: CanIt (www . roaringpenguin . com) on 10.30.31.25 X-OriginalArrivalTime: 20 Mar 2011 00:52:34.0936 (UTC) FILETIME=[19EA4780:01CBE699] Subject: Re: [CentOS] php53-5.3.3-1.el5_6.1 X-BeenThere: centos(a)centos.org X-Mailman-Version: 2.1.9 Reply-To: CentOS mailing list <centos(a)centos.org> List-Id: CentOS mailing list <centos.centos.org> List-Unsubscribe: <http://lists.centos.org/mailman/listinfo/centos>, <mailto:centos-request@centos.org?subject=unsubscribe> List-Archive: <http://lists.centos.org/pipermail/centos> List-Post: <mailto:centos@centos.org> List-Help: <mailto:centos-request@centos.org?subject=help> List-Subscribe: <http://lists.centos.org/mailman/listinfo/centos>, <mailto:centos-request@centos.org?subject=subscribe> Content-Type: text/plain; charset="us-ascii" Content-Transfer-Encoding: 7bit Sender: centos-bounces(a)centos.org Errors-To: centos-bounces(a)centos.org X-pstn-neptune: 0/0/0.00/0 X-pstn-levels: (S:99.90000/99.90000 CV:99.9000 FC:95.5390 LC:95.5390 R:95.9108 P:95.9108 M:97.0282 C:98.6951 ) X-pstn-settings: 1 (0.1500:0.1500) cv gt3 gt2 gt1 p m X-pstn-addresses: from <xxx@xxx> [125/4] -- -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- - - - Jason Pyeron PD Inc. http://www.pdinc.us - - Principal Consultant 10 West 24th Street #100 - - +1 (443) 269-1555 x333 Baltimore, Maryland 21218 - - - -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- This message is copyright PD Inc, subject to license 20080407P00.

2 1

syslog.conf - how to redirect messages by a program name?
by Alexander Farber 21 Mar '11

21 Mar '11

Hello, the "man syslog.conf" explains how to filter syslog messages by facility (auth, authpriv, cron, daemon, kern, ... ) or by priority (debug, info, notice, warning, ...). But how could I redirect messages by a program name, like "drupal" or "php"? For example I have in /var/log/messages: Mar 20 04:20:44 mysite drupal: http://mysite|1300594844|page not found|66.249.66.193|http://mysite/sites/default/files/pictures/picture-7133-1300462418.png||0||sites/default/files/pictures/picture-71333-1300462418.png Mar 20 04:20:50 mysite drupal: http://www.mysite|1300594850|page not found|93.158.148.31|http://www.mysite/viewtopic.php?f=5&t=42639&p=165661&sid=73944439da6ca3054a40f464ce97a628||0||viewtopic.php but I would like them to go under /var/log/drupal (and I'll rotate them later by adding a file to /etc/logrotate.d ....) Regards Alex

6 6

backup script
by madunix＠gmail.com 21 Mar '11

21 Mar '11

I want to create bash script to have a zip copy from a website running on linux /var/www/htdocs/* local on the same box on different directory I am thinking to do a local backup using crontab (snapshot my web) tar -cvzf /tmp/website-$(date +%Y%m%d-%H%M).tgz /var/www/htdocs/* This command will create a file /tmp/website-20110101-1459.tgz I want it run on daily basis and to keep the last 5days backup on the box and remove older version than 5days. Can you point me out. Thanks madunix

11 17

Dvd iso?
by mattias 21 Mar '11

21 Mar '11

Exist none or only livecd? mail mj(a)mjw.se telefon 0104906298

3 4

Re: [CentOS] Add repo for xfig package
by hersh parikh 21 Mar '11

21 Mar '11

Yes Alain is absolutely right about ROCKS. @Alain: Thanks for the information. We'll check what we have in stand alone CentOS.BTW what do you have in yum.conf file? Regards Hersh ________________________________ From: Alain Péan <alain.pean(a)lpp.polytechnique.fr> To: CentOS mailing list <centos(a)centos.org> Sent: Monday, 21 March 2011 7:00 PM Subject: Fw: [CentOS] Add repo for xfig package Le 21/03/2011 13:47, Drew a écrit : >> You don't have your "base" CentOS repository configured. What have you >> done to /etc/yum.repos.d/CentOS-Base.repo, or have you been doing >> something strange to /etc/yum.conf? And what is this "Rocks-5.4" >> repository? > Rocks 5.4 is a recompile of CentOS 5 oriented towards compute clusters. Rocks 5.4 is not a recompile of CentOS 5, it uses CentOS as its base distribution, and add configuration, database, tools, MPI, batch job scheduler etc..., for HPC calculation. As a yum update may break the configuration, /etc/yum.repos.d/ is empty by default. I use myself Rocks, an I populate /etc/yum/repos.d/ by copying what I have on other CentOS workstations, but avoid to do any update. With Rocks, you do update by upgrading to the newest version (which would be Rocks 5.5, based on CentOS 5.6...). Alain -- ========================================================== Alain Péan - LPP/CNRS Administrateur Système/Réseau Laboratoire de Physique des Plasmas - UMR 7648 Observatoire de Saint-Maur 4, av de Neptune, Bat. A 94100 Saint-Maur des Fossés Tel : 01-45-11-42-39 - Fax : 01-48-89-44-33 ========================================================== _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos

2 1

exclude the latest php
by Tim Dunphy 21 Mar '11

21 Mar '11

hey guys, I'm attempting to install php 5.2.7 using the webtatic repo.. but it looks like my exclude isn't working.. I'd appreciate it if someone could point out the mistake I'm making/flaw in my approach... ## machine info [root@ec2-174-129-154-179 yum.repos.d]# cat /etc/redhat-release CentOS release 5.5 (Final) [root@ec2-174-129-154-179 yum.repos.d]# uname -a Linux ec2-174-129-154-179.compute-1.amazonaws.com 2.6.21.7-2.fc8xen #1 SMP Fri Feb 15 12:39:36 EST 2008 i686 i686 i386 GNU/Linux ## try to install php using the webtatic repo [root@ec2-174-129-154-179 yum.repos.d]# yum install php --enablerepo=webtatic Loaded plugins: fastestmirror Loading mirror speeds from cached hostfile * addons: mirror.ash.fastserv.com * base: mirror.nexcess.net * extras: mirror.cogentco.com * updates: mirror.ash.fastserv.com webtatic | 951 B 00:00 Reducing CentOS-5 Testing to included packages only Finished Excluding Packages from Webtatic Repository 5 - i386 Finished Setting up Install Process Resolving Dependencies --> Running transaction check ---> Package php.i386 0:5.3.6-1.w5 set to be updated --> Processing Dependency: httpd-mmn = 20051115 for package: php --> Processing Dependency: php-common = 5.3.6-1.w5 for package: php --> Processing Dependency: php-cli = 5.3.6-1.w5 for package: php --> Processing Dependency: httpd for package: php --> Running transaction check ---> Package httpd.i386 0:2.2.17-1.w5 set to be updated --> Processing Dependency: httpd-tools = 2.2.17-1.w5 for package: httpd ---> Package php-cli.i386 0:5.3.6-1.w5 set to be updated ---> Package php-common.i386 0:5.3.6-1.w5 set to be updated --> Running transaction check ---> Package httpd-tools.i386 0:2.2.17-1.w5 set to be updated --> Finished Dependency Resolution Dependencies Resolved =============================================================================================================================================================================================================== Package Arch Version Repository Size =============================================================================================================================================================================================================== Installing: php i386 5.3.6-1.w5 webtatic 1.3 M Installing for dependencies: httpd i386 2.2.17-1.w5 webtatic 1.1 M httpd-tools i386 2.2.17-1.w5 webtatic 70 k php-cli i386 5.3.6-1.w5 webtatic 2.5 M php-common i386 5.3.6-1.w5 webtatic 569 k Transaction Summary =============================================================================================================================================================================================================== Install 5 Package(s) Upgrade 0 Package(s) Total download size: 5.5 M ## and exclude 5.3.6 (shooting for 5.2.17) [webtatic] name=Webtatic Repository $releasever - $basearch #baseurl=http://repo.webtatic.com/yum/centos/5/$basearch/ mirrorlist=http://repo.webtatic.com/yum/centos/5/$basearch/mirrorlist exclude="5.3.6" enabled=0 gpgcheck=1 gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-webtatic-andy [webtatic-debuginfo] name=Webtatic Repository $releasever - $basearch - Debug #baseurl=http://repo.webtatic.com/yum/centos/5/$basearch/debug/ mirrorlist=http://repo.webtatic.com/yum/centos/5/$basearch/debug/mirrorlist enabled=0 gpgcheck=1 gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-webtatic-andy [webtatic-source] name=Webtatic Repository $releasever - $basearch #baseurl=http://repo.webtatic.com/yum/centos/5/SRPMS/ mirrorlist=http://repo.webtatic.com/yum/centos/5/SRPMS/mirrorlist enabled=0 gpgcheck=1 gpgkey=file:///etc/pki/rpm-gpg/RPM-GPG-KEY-webtatic-andy thanks in advance!! tim -- GPG me!! gpg --keyserver pool.sks-keyservers.net --recv-keys F186197B

3 3

Re: [CentOS] Add repo for xfig package
by hersh parikh 21 Mar '11

21 Mar '11

It says [root@server]# yum list xfig Rocks-5.4 | 1.1 kB 00:00 rpmforge | 1.1 kB 00:00 Error: No matching Packages to list [root@server]# ________________________________ From: Nico Kadel-Garcia <nkadel(a)gmail.com> To: CentOS mailing list <centos(a)centos.org> Sent: Monday, 21 March 2011 5:29 PM Subject: Re: [CentOS] Add repo for xfig package On Mon, Mar 21, 2011 at 7:08 AM, John Doe <jdmls(a)yahoo.com> wrote: > From: hersh parikh <hershparikh12(a)yahoo.com> >>From: Nicolas Thierry-Mieg <Nicolas.Thierry-Mieg(a)imag.fr> >>> xfig and transfig are in centos 5, why don't you just use the regular >>> centos repo? >> We have tried it says no packages available..if its working for you can you >> please paste you .conf file here? > > Strange... As said, it is in the CentOS base repo.. > > # yum list xfig > ... > Available Packages > xfig.x86_64 3.2.4-21.3.el5 base > > http://vault.centos.org/5.5/os/i386/CentOS/xfig-3.2.4-21.3.el5.i386.rpm > http://vault.centos.org/5.5/os/x86_64/CentOS/xfig-3.2.4-21.3.el5.x86_64.rpm What does "yum list xfig" say? _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos

4 4

task md1_resync:9770 blocked for more than 120 seconds and OOM errors
by Alexander Farber 21 Mar '11

21 Mar '11

Hello, yesterday night I had a problem with my server located at a hoster (strato.de). I couldn't ssh to it and over the remote serial console I saw "out of memory" errors (sorry, don't have the text). Then I had reinstall CentOS 5.5/64 bit + all my setup (2h work), because I have a contract with a social network and they will shut down my little card game if it is not reponding. Now the server seems to work ok, but I'm worried about those /var/log/message: kernel: INFO: task md1_resync:9770 blocked for more than 120 seconds. kernel: "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. kernel: md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) kernel: ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c kernel: ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 kernel: 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 kernel: Call Trace: kernel: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 kernel: [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 kernel: [<ffffffff8008ca47>] enqueue_task+0x41/0x56 kernel: [<ffffffff8008cab2>] __activate_task+0x56/0x6d kernel: [<ffffffff8008c897>] dequeue_task+0x18/0x37 kernel: [<ffffffff80062ff8>] thread_return+0x62/0xfe kernel: [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e kernel: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 kernel: [<ffffffff8021b93a>] md_thread+0xf8/0x10e kernel: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 kernel: [<ffffffff8021b842>] md_thread+0x0/0x10e kernel: [<ffffffff8003296e>] kthread+0xfe/0x132 kernel: [<ffffffff8005dfb1>] child_rip+0xa/0x11 kernel: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 kernel: [<ffffffff80032870>] kthread+0x0/0x132 kernel: [<ffffffff8005dfa7>] child_rip+0x0/0x11 kernel: The /var/log/mcelog is empty. # df -h Filesystem Size Used Avail Use% Mounted on /dev/md1 20G 1.4G 18G 8% / /dev/md3 176G 754M 166G 1% /var /dev/md0 993M 30M 913M 4% /boot /dev/md2 263G 352M 250G 1% /home tmpfs 2.0G 0 2.0G 0% /dev/shm Does anybody please have an advice? :-( (Besides "contact or change" your hoster, because it doesn't work). I have 2 disks in "software raid" at that machine, but not much experience with RAID. My dmesg is below. I could reboot the machine in a "rescue mode", but I'm not sure which commands to try there. Thank you Alex Linux version 2.6.18-194.32.1.el5 (mockbuild(a)builder10.centos.org) (gcc version 4.1.2 20080704 (Red Hat 4.1.2-48)) #1 SMP Wed Jan 5 17:52:25 EST 2011 Command line: root=/dev/md1 console=tty0 console=ttyS0,57600 BIOS-provided physical RAM map: BIOS-e820: 0000000000010000 - 000000000009f000 (usable) BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved) BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved) BIOS-e820: 0000000000100000 - 00000000ddfb0000 (usable) BIOS-e820: 00000000ddfb0000 - 00000000ddfbe000 (ACPI data) BIOS-e820: 00000000ddfbe000 - 00000000ddfe0000 (ACPI NVS) BIOS-e820: 00000000ddfe0000 - 00000000ddfee000 (reserved) BIOS-e820: 00000000ddff0000 - 00000000de000000 (reserved) BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved) BIOS-e820: 0000000100000000 - 0000000120000000 (usable) DMI present. ACPI: RSDP (v000 ACPIAM ) @ 0x00000000000faf80 ACPI: RSDT (v001 032510 RSDT1503 0x20100325 MSFT 0x00000097) @ 0x00000000ddfb0000 ACPI: FADT (v002 032510 FACP1503 0x20100325 MSFT 0x00000097) @ 0x00000000ddfb0200 ACPI: MADT (v001 032510 APIC1503 0x20100325 MSFT 0x00000097) @ 0x00000000ddfb0390 ACPI: MCFG (v001 032510 OEMMCFG 0x20100325 MSFT 0x00000097) @ 0x00000000ddfb0400 ACPI: OEMB (v001 032510 OEMB1503 0x20100325 MSFT 0x00000097) @ 0x00000000ddfbe040 ACPI: HPET (v001 032510 OEMHPET 0x20100325 MSFT 0x00000097) @ 0x00000000ddfb48c0 ACPI: SSDT (v001 A M I POWERNOW 0x00000001 AMD 0x00000001) @ 0x00000000ddfb4900 ACPI: DSDT (v001 A96B3 A96B3210 0x00000210 INTL 0x20051117) @ 0x0000000000000000 No NUMA configuration found Faking a node at 0000000000000000-0000000120000000 Bootmem setup node 0 0000000000000000-0000000120000000 Memory for crash kernel (0x0 to 0x0) notwithin permissible range disabling kdump On node 0 totalpages: 1022763 DMA zone: 2627 pages, LIFO batch:0 DMA32 zone: 890856 pages, LIFO batch:31 Normal zone: 129280 pages, LIFO batch:31 ACPI: PM-Timer IO Port: 0x808 ACPI: Local APIC address 0xfee00000 ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled) Processor #0 0:4 APIC version 16 ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled) Processor #1 0:4 APIC version 16 ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled) Processor #2 0:4 APIC version 16 ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled) Processor #3 0:4 APIC version 16 ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0]) IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23 ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl) ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level) ACPI: IRQ0 used by override. ACPI: IRQ2 used by override. ACPI: IRQ9 used by override. Setting APIC routing to physical flat ACPI: HPET id: 0x8300 base: 0xfed00000 Using ACPI (MADT) for SMP configuration information Nosave address range: 000000000009f000 - 00000000000a0000 Nosave address range: 00000000000a0000 - 00000000000e4000 Nosave address range: 00000000000e4000 - 0000000000100000 Nosave address range: 00000000ddfb0000 - 00000000ddfbe000 Nosave address range: 00000000ddfbe000 - 00000000ddfe0000 Nosave address range: 00000000ddfe0000 - 00000000ddfee000 Nosave address range: 00000000ddfee000 - 00000000ddff0000 Nosave address range: 00000000ddff0000 - 00000000de000000 Nosave address range: 00000000de000000 - 00000000ff700000 Nosave address range: 00000000ff700000 - 0000000100000000 Allocating PCI resources starting at e0000000 (gap: de000000:21700000) SMP: Allowing 4 CPUs, 0 hotplug CPUs Built 1 zonelists. Total pages: 1022763 Kernel command line: root=/dev/md1 console=tty0 console=ttyS0,57600 Initializing CPU#0 PID hash table entries: 4096 (order: 12, 32768 bytes) Console: colour VGA+ 80x25 Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes) Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes) Checking aperture... CPU 0: aperture @ 4000000 size 32 MB Aperture too small (32 MB) No AGP bridge found Your BIOS doesn't leave a aperture memory hole Please enable the IOMMU option in the BIOS setup This costs you 64 MB of RAM Mapping aperture over 65536 KB of RAM @ 4000000 Nosave address range: 0000000004000000 - 0000000008000000 ACPI: DMAR not present Memory: 4016200k/4718592k available (2575k kernel code, 144564k reserved, 1304k data, 212k init) Calibrating delay loop (skipped), value calculated using timer frequency.. 5000.24 BogoMIPS (lpj=2500120) Security Framework v1.0.0 initialized SELinux: Initializing. SELinux: Starting in permissive mode selinux_register_security: Registering secondary module capability Capability LSM initialized as secondary Mount-cache hash table entries: 256 CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 0/0 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 0 SMP alternatives: switching to UP code ACPI: Core revision 20060707 Using local APIC timer interrupts. Detected 12.500 MHz APIC timer. SMP alternatives: switching to SMP code Booting processor 1/4 APIC 0x1 Initializing CPU#1 Calibrating delay using timer specific routine.. 5000.12 BogoMIPS (lpj=2500063) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 1/1 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 1 Quad-Core AMD Opteron(tm) Processor 1381 stepping 02 SMP alternatives: switching to SMP code Booting processor 2/4 APIC 0x2 Initializing CPU#2 Calibrating delay using timer specific routine.. 5000.18 BogoMIPS (lpj=2500094) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 2/2 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 2 Quad-Core AMD Opteron(tm) Processor 1381 stepping 02 SMP alternatives: switching to SMP code Booting processor 3/4 APIC 0x3 Initializing CPU#3 Calibrating delay using timer specific routine.. 4999.17 BogoMIPS (lpj=2499587) CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line) CPU: L2 Cache: 512K (64 bytes/line) CPU 3/3 -> Node 0 CPU: Physical Processor ID: 0 CPU: Processor Core ID: 3 Quad-Core AMD Opteron(tm) Processor 1381 stepping 02 Brought up 4 CPUs testing NMI watchdog ... OK. time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer. time.c: Detected 2500.123 MHz processor. sizeof(vma)=176 bytes sizeof(page)=56 bytes sizeof(inode)=560 bytes sizeof(dentry)=216 bytes sizeof(ext3inode)=760 bytes sizeof(buffer_head)=96 bytes sizeof(skbuff)=248 bytes migration_cost=230 checking if image is initramfs... it is Freeing initrd memory: 2614k freed NET: Registered protocol family 16 ACPI: bus type pci registered PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved PCI: Not using MMCONFIG. PCI: Using configuration type 1 PCI: Using configuration type 1 for extended access ACPI: Interpreter enabled ACPI: Using IOAPIC for interrupt routing ACPI: No dock devices found. ACPI: PCI Root Bridge [PCI0] (0000:00) PCI: set SATA to AHCI mode PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1 PCI: Transparent bridge - 0000:00:14.4 ACPI: PCI Interrupt Routing Table [\_SB_.PCI0._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0P1._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE4._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.PCE5._PRT] ACPI: PCI Interrupt Routing Table [\_SB_.PCI0.P0PC._PRT] ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 12 14 15) ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 *15) ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15) ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled. ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 *11 12 14 15) ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled. Linux Plug and Play Support v0.97 (c) Adam Belay pnp: PnP ACPI init pnp: PnP ACPI: found 14 devices usbcore: registered new driver usbfs usbcore: registered new driver hub PCI: Using ACPI for IRQ routing PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report PCI: Cannot allocate resource region 1 of device 0000:00:14.0 NetLabel: Initializing NetLabel: domain hash size = 128 NetLabel: protocols = UNLABELED CIPSOv4 NetLabel: unlabeled traffic allowed by default hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0, 0 hpet0: 4 32-bit timers, 14318180 Hz ACPI: DMAR not present PCI-DMA: Disabling AGP. PCI-DMA: aperture base @ 4000000 size 65536 KB PCI-DMA: using GART IOMMU. PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture pnp: 00:08: iomem range 0xfec00000-0xfec00fff has been reserved pnp: 00:08: iomem range 0xfee00000-0xfee00fff has been reserved pnp: 00:09: iomem range 0xffb80000-0xffbfffff could not be reserved pnp: 00:0b: ioport range 0xa00-0xa0f has been reserved pnp: 00:0b: ioport range 0xa10-0xa1f has been reserved pnp: 00:0c: iomem range 0xe0000000-0xefffffff has been reserved pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved pnp: 00:0d: iomem range 0xc0000-0xcffff could not be reserved pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved pnp: 00:0d: iomem range 0x100000-0xddffffff could not be reserved PCI: Error while updating region 0000:00:14.0/1 (f0000004 != 8000a014) PCI: Bridge: 0000:00:01.0 IO window: c000-cfff MEM window: fe800000-fe9fffff PREFETCH window 0x00000000fc000000-0x00000000fdffffff PCI: Bridge: 0000:00:04.0 IO window: d000-dfff MEM window: fea00000-feafffff PREFETCH window: disabled. PCI: Bridge: 0000:00:05.0 IO window: e000-efff MEM window: feb00000-febfffff PREFETCH window: disabled. PCI: Bridge: 0000:00:14.4 IO window: disabled. MEM window: disabled. PREFETCH window: disabled. PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:05.0 to 64 NET: Registered protocol family 2 IP route cache hash table entries: 131072 (order: 8, 1048576 bytes) TCP established hash table entries: 262144 (order: 10, 4194304 bytes) TCP bind hash table entries: 65536 (order: 8, 1048576 bytes) TCP: Hash tables configured (established 262144 bind 65536) TCP reno registered audit: initializing netlink socket (disabled) type=2000 audit(1300575339.480:1): initialized Total HugeTLB memory allocated, 0 VFS: Disk quotas dquot_6.5.1 Dquot-cache hash table entries: 512 (order 0, 4096 bytes) SELinux: Registering netfilter hooks Initializing Cryptographic API alg: No test for crc32c (crc32c-generic) ksign: Installing public key data Loading keyring - Added public key 1DF8C62584B4E7F2 - User ID: CentOS (Kernel Module GPG key) io scheduler noop registered io scheduler anticipatory registered io scheduler deadline registered io scheduler cfq registered (default) Boot video device is 0000:01:05.0 PCI: Setting latency timer of device 0000:00:04.0 to 64 PCI: Setting latency timer of device 0000:00:05.0 to 64 pci_hotplug: PCI Hot Plug PCI Core version: 0.5 ACPI: duty_cycle spans bit 4 ACPI: CPU0 (power states: C1[C1] C2[C2] C3[C3]) Real Time Clock Driver v1.12ac hpet_resources: 0xfed00000 is busy Non-volatile memory driver v1.2 Linux agpgart interface v0.101 (c) Dave Jones Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A 00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A 00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A brd: module loaded Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2 ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx SB600_PATA: IDE controller at PCI slot 0000:00:14.1 GSI 16 sharing vector 0xC1 and IRQ 16 ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 193 SB600_PATA: chipset revision 0 SB600_PATA: not 100% native mode: will probe irqs later ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:pio, hdb:pio Probing IDE interface ide0... Probing IDE interface ide0... Probing IDE interface ide1... ide-floppy driver 0.99.newide usbcore: registered new driver hiddev usbcore: registered new driver usbhid drivers/usb/input/hid-core.c: v2.6:USB HID core driver PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1 PNP: PS/2 controller doesn't have AUX irq; using default 12 serio: i8042 KBD port at 0x60,0x64 irq 1 serio: i8042 AUX port at 0x60,0x64 irq 12 mice: PS/2 mouse device common for all mice md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27 md: bitmap version 4.39 TCP bic registered Initializing IPsec netlink socket NET: Registered protocol family 1 NET: Registered protocol family 17 ACPI: (supports S0 S1 S3 S4 S5) Initalizing network drop monitor service Freeing unused kernel memory: 212k freed Write protecting the kernel read-only data: 505k GSI 17 sharing vector 0xC9 and IRQ 17 ACPI: PCI Interrupt 0000:00:13.5[D] -> GSI 19 (level, low) -> IRQ 201 ehci_hcd 0000:00:13.5: EHCI Host Controller ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1 ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround ehci_hcd 0000:00:13.5: debug port 1 ehci_hcd 0000:00:13.5: irq 201, io mem 0xfe7ff000 ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004 usb usb1: configuration #1 chosen from 1 choice hub 1-0:1.0: USB hub found hub 1-0:1.0: 10 ports detected ohci_hcd: 2005 April 22 USB 1.1 'Open' Host Controller (OHCI) Driver (PCI) ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 193 ohci_hcd 0000:00:13.0: OHCI Host Controller ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2 ohci_hcd 0000:00:13.0: irq 193, io mem 0xfe7fe000 usb usb2: configuration #1 chosen from 1 choice hub 2-0:1.0: USB hub found hub 2-0:1.0: 2 ports detected GSI 18 sharing vector 0xD1 and IRQ 18 ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 209 ohci_hcd 0000:00:13.1: OHCI Host Controller ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3 ohci_hcd 0000:00:13.1: irq 209, io mem 0xfe7fd000 usb usb3: configuration #1 chosen from 1 choice hub 3-0:1.0: USB hub found hub 3-0:1.0: 2 ports detected GSI 19 sharing vector 0xD9 and IRQ 19 ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 217 ohci_hcd 0000:00:13.2: OHCI Host Controller ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4 ohci_hcd 0000:00:13.2: irq 217, io mem 0xfe7fc000 usb usb4: configuration #1 chosen from 1 choice hub 4-0:1.0: USB hub found hub 4-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 209 ohci_hcd 0000:00:13.3: OHCI Host Controller ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5 ohci_hcd 0000:00:13.3: irq 209, io mem 0xfe7fb000 usb usb5: configuration #1 chosen from 1 choice hub 5-0:1.0: USB hub found hub 5-0:1.0: 2 ports detected ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 217 ohci_hcd 0000:00:13.4: OHCI Host Controller ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6 ohci_hcd 0000:00:13.4: irq 217, io mem 0xfe7fa000 usb usb6: configuration #1 chosen from 1 choice hub 6-0:1.0: USB hub found hub 6-0:1.0: 2 ports detected USB Universal Host Controller Interface driver v3.0 md: raid1 personality registered for level 1 SCSI subsystem initialized libata version 3.00 loaded. ahci 0000:00:12.0: version 3.0 GSI 20 sharing vector 0xE1 and IRQ 20 ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 225 ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part scsi0 : ahci scsi1 : ahci scsi2 : ahci scsi3 : ahci ata1: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ff900 irq 225 ata2: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ff980 irq 225 ata3: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ffa00 irq 225 ata4: SATA max UDMA/133 abar m1024@0xfe7ff800 port 0xfe7ffa80 irq 225 ata1: softreset failed (device not ready) ata1: failed due to HW bug, retry pmp=0 ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata1.00: ATA-8: Hitachi HDS721050CLA362, JP2OA39C, max UDMA/133 ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata1.00: SB600 AHCI: limiting to 255 sectors per cmd ata1.00: SB600 AHCI: limiting to 255 sectors per cmd ata1.00: configured for UDMA/133 ata2: softreset failed (device not ready) ata2: failed due to HW bug, retry pmp=0 ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300) ata2.00: ATA-8: Hitachi HDS721050CLA362, JP2OA39C, max UDMA/133 ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32) ata2.00: SB600 AHCI: limiting to 255 sectors per cmd ata2.00: SB600 AHCI: limiting to 255 sectors per cmd ata2.00: configured for UDMA/133 ata3: SATA link down (SStatus 0 SControl 300) ata4: SATA link down (SStatus 0 SControl 300) Vendor: ATA Model: Hitachi HDS72105 Rev: JP2O Type: Direct-Access ANSI SCSI revision: 05 SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB) sda: Write Protect is off sda: Mode Sense: 00 3a 00 00 SCSI device sda: drive cache: write back sda: sda1 sda2 sda3 sda4 < sda5 sda6 > sd 0:0:0:0: Attached scsi disk sda Vendor: ATA Model: Hitachi HDS72105 Rev: JP2O Type: Direct-Access ANSI SCSI revision: 05 SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB) sdb: Write Protect is off sdb: Mode Sense: 00 3a 00 00 SCSI device sdb: drive cache: write back sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 > sd 1:0:0:0: Attached scsi disk sdb device-mapper: uevent: version 1.0.3 device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel(a)redhat.com device-mapper: dm-raid45: initialized v0.2594l md: Autodetecting RAID arrays. md: autorun ... md: considering sdb6 ... md: adding sdb6 ... md: sdb5 has different UUID to sdb6 md: sdb3 has different UUID to sdb6 md: sdb1 has different UUID to sdb6 md: adding sda6 ... md: sda5 has different UUID to sdb6 md: sda3 has different UUID to sdb6 md: sda1 has different UUID to sdb6 md: created md3 md: bind<sda6> md: bind<sdb6> md: running: <sdb6><sda6> raid1: raid set md3 active with 2 out of 2 mirrors md: considering sdb5 ... md: adding sdb5 ... md: sdb3 has different UUID to sdb5 md: sdb1 has different UUID to sdb5 md: adding sda5 ... md: sda3 has different UUID to sdb5 md: sda1 has different UUID to sdb5 md: created md2 md: bind<sda5> md: bind<sdb5> md: running: <sdb5><sda5> raid1: raid set md2 active with 2 out of 2 mirrors md: considering sdb3 ... md: adding sdb3 ... md: sdb1 has different UUID to sdb3 md: adding sda3 ... md: sda1 has different UUID to sdb3 md: created md1 md: bind<sda3> md: bind<sdb3> md: running: <sdb3><sda3> raid1: raid set md1 active with 2 out of 2 mirrors md: considering sdb1 ... md: adding sdb1 ... md: adding sda1 ... md: created md0 md: bind<sda1> md: bind<sdb1> md: running: <sdb1><sda1> raid1: raid set md0 active with 2 out of 2 mirrors md: ... autorun DONE. kjournald starting. Commit interval 5 seconds EXT3-fs: mounted filesystem with ordered data mode. SELinux: Disabled at runtime. SELinux: Unregistering netfilter hooks type=1404 audit(1300575368.057:2): selinux=0 auid=4294967295 ses=4294967295 piix4_smbus 0000:00:14.0: Found 0000:00:14.0 device EDAC MC: Ver: 2.0.1 Jan 5 2011 EDAC amd64_edac: Ver: 3.2.0 Jan 5 2011 EDAC amd64: This node reports that Memory ECC is currently disabled, set F3x44[22] (0000:00:18.3). EDAC amd64: WARNING: ECC is disabled by BIOS. Module will NOT be loaded. Either Enable ECC in the BIOS, or set 'ecc_enable_override'. Also, use of the override can cause unknown side effects. amd64_edac: probe of 0000:00:18.2 failed with error -22 Floppy drive(s): fd0 is 1.44M e1000e: Intel(R) PRO/1000 Network Driver - 1.0.2-k3.1 e1000e: Copyright (c) 1999-2008 Intel Corporation. ACPI: PCI Interrupt 0000:02:00.0[A] -> GSI 16 (level, low) -> IRQ 193 PCI: Setting latency timer of device 0000:02:00.0 to 64 input: PC Speaker as /class/input/input0 e1000e 0000:02:00.0: Warning: detected ASPM enabled in EEPROM eth0: (PCI Express:2.5GB/s:Width x1) 40:61:86:ee:20:46 eth0: Intel(R) PRO/1000 Network Connection eth0: MAC: 2, PHY: 2, PBA No: ffffff-0ff ACPI: PCI Interrupt 0000:03:00.0[A] -> GSI 17 (level, low) -> IRQ 209 PCI: Setting latency timer of device 0000:03:00.0 to 64 sd 0:0:0:0: Attached scsi generic sg0 type 0 sd 1:0:0:0: Attached scsi generic sg1 type 0 e1000e 0000:03:00.0: Warning: detected ASPM enabled in EEPROM eth1: (PCI Express:2.5GB/s:Width x1) 40:61:86:ee:20:47 eth1: Intel(R) PRO/1000 Network Connection eth1: MAC: 2, PHY: 2, PBA No: ffffff-0ff shpchp: Standard Hot Plug PCI Controller Driver version: 0.4 floppy0: no floppy controllers found Floppy drive(s): fd0 is 1.44M floppy0: no floppy controllers found lp: driver loaded but no devices found ACPI: Power Button (FF) [PWRF] ACPI: Power Button (CM) [PWRB] ACPI: Mapper loaded dell-wmi: No known WMI GUID found md: Autodetecting RAID arrays. md: autorun ... md: ... autorun DONE. device-mapper: multipath: version 1.0.5 loaded loop: loaded (max 8 devices) EXT3 FS on md1, internal journal kjournald starting. Commit interval 5 seconds EXT3 FS on md3, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on md0, internal journal EXT3-fs: mounted filesystem with ordered data mode. kjournald starting. Commit interval 5 seconds EXT3 FS on md2, internal journal EXT3-fs: mounted filesystem with ordered data mode. Adding 3999736k swap on /dev/sda2. Priority:-1 extents:1 across:3999736k Adding 3999736k swap on /dev/sdb2. Priority:-2 extents:1 across:3999736k powernow-k8: Found 1 Quad-Core AMD Opteron(tm) Processor 1381 processors (4 cpu cores) (version 2.20.00) powernow-k8: 0 : fid 0x0 gid 0x0 (2500 MHz) powernow-k8: 1 : fid 0x0 gid 0x0 (1800 MHz) powernow-k8: 2 : fid 0x0 gid 0x0 (1300 MHz) powernow-k8: 3 : fid 0x0 gid 0x0 (800 MHz) ip_tables: (C) 2000-2006 Netfilter Core Team Netfilter messages via NETLINK v0.30. ip_conntrack version 2.4 (8192 buckets, 65536 max) - 304 bytes per conntrack NET: Registered protocol family 10 lo: Disabled Privacy Extensions IPv6 over IPv4 tunneling driver ADDRCONF(NETDEV_UP): eth0: link is not ready e1000e: eth0 NIC Link is Up 100 Mbps Full Duplex, Flow Control: None eth0: 10/100 speed: disabling TSO ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready ADDRCONF(NETDEV_UP): eth1: link is not ready md: syncing RAID array md0 md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. md: using 128k window, over a total of 1023936 blocks. md: delaying resync of md2 until md0 has finished resync (they share one or more physical units) md: delaying resync of md1 until md0 has finished resync (they share one or more physical units) md: delaying resync of md2 until md0 has finished resync (they share one or more physical units) md: md0: sync done. md: syncing RAID array md2 md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. md: using 128k window, over a total of 277728192 blocks. md: delaying resync of md1 until md2 has finished resync (they share one or more physical units) RAID1 conf printout: --- wd:2 rd:2 disk 0, wo:0, o:1, dev:sda1 disk 1, wo:0, o:1, dev:sdb1 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 INFO: task md1_resync:9770 blocked for more than 120 seconds. "echo 0 > /proc/sys/kernel/hung_task_timeout_secs" disables this message. md1_resync D ffff81011edba820 0 9770 55 9768 (L-TLB) ffff810083259d70 0000000000000046 0000000000000000 ffff81011ea66e0c ffff81011ea66c0c 000000000000000a ffff81011ccc27a0 ffff81011edba820 000011d56f2a0b28 000000000000100f ffff81011ccc2988 000000028008b4d7 Call Trace: [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021af66>] md_do_sync+0x1d8/0x833 [<ffffffff8008ca47>] enqueue_task+0x41/0x56 [<ffffffff8008cab2>] __activate_task+0x56/0x6d [<ffffffff8008c897>] dequeue_task+0x18/0x37 [<ffffffff80062ff8>] thread_return+0x62/0xfe [<ffffffff800a0b5f>] autoremove_wake_function+0x0/0x2e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b93a>] md_thread+0xf8/0x10e [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff8021b842>] md_thread+0x0/0x10e [<ffffffff8003296e>] kthread+0xfe/0x132 [<ffffffff8005dfb1>] child_rip+0xa/0x11 [<ffffffff800a0947>] keventd_create_kthread+0x0/0xc4 [<ffffffff80032870>] kthread+0x0/0x132 [<ffffffff8005dfa7>] child_rip+0x0/0x11 md: md2: sync done. md: syncing RAID array md1 md: minimum _guaranteed_ reconstruction speed: 1000 KB/sec/disc. md: using maximum available idle IO bandwidth (but not more than 200000 KB/sec) for reconstruction. md: using 128k window, over a total of 20479936 blocks. RAID1 conf printout: --- wd:2 rd:2 disk 0, wo:0, o:1, dev:sda5 disk 1, wo:0, o:1, dev:sdb5 md: md1: sync done. RAID1 conf printout: --- wd:2 rd:2 disk 0, wo:0, o:1, dev:sda3 disk 1, wo:0, o:1, dev:sdb3

3 7

Re: [CentOS] Add repo for xfig package
by hersh parikh 21 Mar '11

21 Mar '11

May be our repository is different then yours. Since it's working for you can you paste baseurls in your yum repo fie? It would be very useful. Regards Hersh ________________________________ From: John Doe <jdmls(a)yahoo.com> To: CentOS mailing list <centos(a)centos.org> Sent: Monday, 21 March 2011 4:38 PM Subject: Re: [CentOS] Add repo for xfig package From: hersh parikh <hershparikh12(a)yahoo.com> >From: Nicolas Thierry-Mieg <Nicolas.Thierry-Mieg(a)imag.fr> >> xfig and transfig are in centos 5, why don't you just use the regular >> centos repo? > We have tried it says no packages available..if its working for you can you > please paste you .conf file here? Strange... As said, it is in the CentOS base repo.. # yum list xfig ... Available Packages xfig.x86_64 3.2.4-21.3.el5 base http://vault.centos.org/5.5/os/i386/CentOS/xfig-3.2.4-21.3.el5.i386.rpm http://vault.centos.org/5.5/os/x86_64/CentOS/xfig-3.2.4-21.3.el5.x86_64.rpm JD _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos

1 0

Re: [CentOS] Add repo for xfig package
by hersh parikh 21 Mar '11

21 Mar '11

We have tried it says no packages available..if its working for you can you please paste you .conf file here? ________________________________ From: Nicolas Thierry-Mieg <Nicolas.Thierry-Mieg(a)imag.fr> To: CentOS mailing list <centos(a)centos.org> Sent: Friday, 18 March 2011 7:35 PM Subject: Re: [CentOS] Add repo for xfig package hersh parikh wrote: > Hi All > > We want to install packages like xfig and transfig on centos 5.5. We > found rpms available but them but it seems there are lot of dependencies > for these packages. So we would like to setup yum repo for this. Can > anyone suggest trusted baseurl for yum repo? xfig and transfig are in centos 5, why don't you just use the regular centos repo? _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos

3 2

Rsync mirroring dev.centos.org
by Jason Pyeron 20 Mar '11

20 Mar '11

Is there a preferred way to maintain a local mirror of dev.centos.org? -- -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- - - - Jason Pyeron PD Inc. http://www.pdinc.us - - Principal Consultant 10 West 24th Street #100 - - +1 (443) 269-1555 x333 Baltimore, Maryland 21218 - - - -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- This message is copyright PD Inc, subject to license 20080407P00.

1 0

php53-5.3.3-1.el5_6.1
by Jason Pyeron 20 Mar '11

20 Mar '11

Curious I do not see the php53 in the yum centos 5 repositories. Has this package been excluded? http://ftp.redhat.com/pub/redhat/linux/enterprise/5Server/en/os/SRPMS/php53…. 3-1.el5_6.1.src.rpm http://ftp.redhat.com/pub/redhat/linux/enterprise/5Client/en/os/SRPMS/php53…. 3-1.el5_6.1.src.rpm -- -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- - - - Jason Pyeron PD Inc. http://www.pdinc.us - - Principal Consultant 10 West 24th Street #100 - - +1 (443) 269-1555 x333 Baltimore, Maryland 21218 - - - -=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=-=- This message is copyright PD Inc, subject to license 20080407P00.

4 5

respawning apache on centos
by Dave Stevens 19 Mar '11

19 Mar '11

Hi I have a centos instance on a host where uname -a shows: Linux cl28810.com 2.6.18-194.26.1.el5.028stab079.2PAE #1 SMP Fri Dec 17 19:34:22 MSK 2010 i686 i686 i386 GNU/Linux Periodically my ssh access and http access slow dramatically and I get out of memory when trying to do rudimentary stuff like ls. I've been advised by tech support to try service httpd restart. This works. But the first thing that happens after the command is issued is that the load goes up to about 15 then slowly declines to a more typical figure, in the range feom .1 to 1.3, which is fine. It takes several minutes before the site is really usable. I now have 22 apache instances out of 66 total processes, which seems excessive. One site hosted, running drupal 7, 1.5G RAM lots of disk spece, two cores, Xeon based host. I don't know if this is an apache issue or CentOS related or what. Ideas? Debugging I can do? Dave -- “When facism comes to America it will be wrapped in the flag and carrying a cross.” - Sinclair Lewis, It Can't Happen Here, 1935

8 11

Re: [CentOS] Dvd iso?
by aly.khimji＠gmail.com 19 Mar '11

19 Mar '11

They are installer only, if I recall correctly Aly ------Original Message------ From: mattias Sender: centos-bounces(a)centos.org To: 'CentOS mailing list' ReplyTo: CentOS mailing list Subject: Re: [CentOS] Dvd iso? Sent: Mar 19, 2011 5:22 PM Yes I find it Are the dvd only installer or live cd too Hope installer only mail mj(a)mjw.se telefon 0104906298 -----Original Message----- From: centos-bounces(a)centos.org [mailto:centos-bounces@centos.org] On Behalf Of John R Pierce Sent: Saturday, March 19, 2011 10:20 PM To: centos(a)centos.org Subject: Re: [CentOS] Dvd iso? On 03/19/11 2:10 PM, mattias wrote: > Exist none or only livecd? many of the http/ftp mirrors don't carry them because they are so large, and files > 2gb can be problematic for downloads. the standard way of getting the dvd iso is via bittorrent. go here to find a mirror near you that has direct DVD download http://www.centos.org/modules/tinycontent/index.php?id=30 _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos Sent from my BlackBerry device on the Rogers Wireless Network

2 1

Re: [CentOS] Dvd iso?
by aly.khimji＠gmail.com 19 Mar '11

19 Mar '11

There is a dvd iso, just go through a few mirrors. Not all of them have it. Not sure if that's what u meant, but if so it does exist. Aly ------Original Message------ From: mattias Sender: centos-bounces(a)centos.org To: centos(a)centos.org ReplyTo: CentOS mailing list Subject: [CentOS] Dvd iso? Sent: Mar 19, 2011 5:10 PM Exist none or only livecd? mail mj(a)mjw.se telefon 0104906298 _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos Sent from my BlackBerry device on the Rogers Wireless Network

1 0

httpd cannot serve web page on port 2812 (for Monit)
by Rogelio 19 Mar '11

19 Mar '11

Might there be anything CentOS related on why I cannot access the Monit GUI system on http://box-running-monit.com:2812 ? I am using a very basic /etc/monit.conf config, but I cannot get it serve the web page on my box The service start and stops fine (e.g. "/etc/init.d/monit start"), and I have it set to listen to port 2812 in the "/etc/monit.conf file" (so far, kept the default) e.g. in "/etc/monit.d/monitrc" file set daemon 60 set logfile syslog facility log_daemon set mailserver localhost set mail-format { from: monit(a)server1.example.com } set alert me(a)mydomain.com set httpd port 2812 check process sshd with pidfile /var/run/sshd.pid start program "/etc/init.d/sshd start" stop program "/etc/init.d/sshd stop" if failed port 22 protocol ssh then restart if 5 restarts within 5 cycles then timeout (I also enabled the 2812 port using CentOS's "system-config-securitylevel" command, which added the right IPtables entries, which I see okay on "iptables -L") -- Also on LinkedIn? Feel free to connect if you too are an open networker: scubacuda(a)gmail.com

2 4

PHP - Security Updates
by Tom Brown 19 Mar '11

19 Mar '11

Hi I am wondering if this has made it into any updates? http://web.nvd.nist.gov/view/vuln/detail?vulnId=CVE-2010-4645 thanks

2 1

Safe/sane tempfile creation?
by Dr. Ed Morbius 19 Mar '11

19 Mar '11

I'm used to Debian-based distros which have a tempfile(1) utility for safely and sanely creating temporary files. There isn't a comperable utility for RHEL/CentOS systems. I've been exercising Google-fu looking for a good robust tempfile generation idiom, but haven't turned one up yet. Hence this appeal to the lazyweb. -- Dr. Ed Morbius, Chief Scientist / | Robot Wrangler / Staff Psychologist | When you seek unlimited power Krell Power Systems Unlimited | Go to Krell!

2 2

Cannot %include in CentOS 5.5 kickstart
by whitivery 19 Mar '11

19 Mar '11

I've previously used includes in CentOS 4.4 and they worked fine. But in CentOS 5.5, trying to specify a driver disk via an include does not work. If I instead specify it directly, it loads fine. When it fails (because it can't see the disk drive - needs the driver disk to see the hard disk), in Console 2 I can see that /tmp/drvdisk exists and has the line I wrote to it. I see nothing that looks wrong in any log or kickstart file/fragment in /tmp. Any ideas? Here's my complete kickstart to show/test this: # Minimal Kickstart test for CentOS 5.5 to show %include problem url --url=http://10.0.4.157/cblr/links/CentOS5.5-i386 text lang en_US.UTF-8 keyboard us timezone --utc America/New_York install bootloader --location=mbr clearpart --all --initlabel network --device eth0 --bootproto dhcp firewall --disabled selinux --disabled rootpw --iscrypted \$1\$x6z.qvwE\$7Zg9g1rCEgvOBoA7Oo/HF1 zerombr authconfig --useshadow --enablemd5 part /boot --fstype ext3 --size 100 --asprimary part / --fstype ext3 --size 1 --grow --asprimary part /var --fstype ext3 --size 10000 part swap --recommended # This does not work %include /tmp/drvdisk # This works #driverdisk --source=nfs:10.0.4.157:/srv/cobbler/RHEL5.5_x86_402_409_410_DD.img %packages @base @core %pre --erroronfail echo "driverdisk --source=nfs:10.0.4.157:/srv/cobbler/RHEL5.5_x86_402_409_410_DD.img" > /tmp/drvdisk # (end of kickstart file)

3 6

rpm split
by Janez Kosmrlj 18 Mar '11

18 Mar '11

Hi, I have a custom rpm for our application. The problem is that it grew old and fat. It's about 30 MB. So i would like to split it into two parts. One big part that almost never changes and one smaller part that is changed more frequently. But i don't know how to write the spec file so a simple yum update will install both packages and it won't create any problems. Any suggestions?

2 1

modprobe :: not finding existing .ko
by Adrian Sevcenco 18 Mar '11

18 Mar '11

Hi! I try to load an module that it is found in curent /lib/modules/`uname -r` tree ... root@sevcenco: ~ # ls -l /lib/modules/`uname -r`/kernel/drivers/crypto/padlock-* -rwxr--r-- 1 root root 14296 Mar 16 19:37 /lib/modules/2.6.38-0.el5.elrepo/kernel/drivers/crypto/padlock-aes.ko -rwxr--r-- 1 root root 10808 Mar 16 19:37 /lib/modules/2.6.38-0.el5.elrepo/kernel/drivers/crypto/padlock-sha.ko but if i try : root@sevcenco: ~ # modprobe -v padlock-aes.ko FATAL: Module padlock_aes.ko not found. notice the change from - to _ Any idea about this? or more abstract: have anyone succeed to use padlock (via) hardware with openssl (or other software) in centos? Thanks, Adrian

8 8

creating a htpasswd file for certain urls
by Agnello George 18 Mar '11

18 Mar '11

H All I am in a kind of fix , i got a website ( beta.somesite.com ) .. that need to be password protected , however there are two URLs that should be allowed to all with out password access. Ona cent os box 5.5 i am running apache . the entire site needs passwd protection except for the Below Urls . http://beta.somesite.com/wp-content/uploads/2011/03/large_1990782-e12992296… http://beta.somesite.com/?cat=592&feed=rss2 Your advice will be of great help -- Regards Agnello D'souza

5 5

Replace NIS by Active Directory
by MOKRANI Rachid 18 Mar '11

18 Mar '11

Hi, I'm looking a wiki or share experience for replace NIS authentication by an existing Active directory Server (W2003). The problem is on the management of id and gid. How to move 1000 actual NIS users to AD ? How to keep the same id and gid for this 1000 users ? What's happen with nfs linux server and acess with gid and/id ? Use the same user/password for linux and Windows clients authentification? We test a solution who work very well. It's Centrify comercial software http://www.centrify.com/directcontrol/overview.asp . But we are looking a freeware solution. (kerberos ? openldap ? pam ? ...) Does someone has already successfully replace NIS by Ad authentification with freeware solution ? Regards. __________________________ Notre adresse de messagerie évolue pour plus de simplicité vers : prenom.nom(a)ifpen.fr. La racine @ifpenergiesnouvelles.fr reste néanmoins active. Our e-mail address is changing to firstname.surname(a)ifpen.fr. Nevertheless, messages sent to the domain @ifpenergiesnouvelles.fr will still be delivered. Ce message (et toutes ses pièces jointes éventuelles) est confidentiel et établi à l'intention exclusive de ses destinataires. Toute utilisation de ce message non conforme à sa destination, toute diffusion ou toute publication, totale ou partielle, est interdite, sauf autorisation expresse. IFP Energies nouvelles décline toute responsabilité au titre de ce message. This message and any attachments (the message) are confidential and intended solely for the addressees. Any unauthorised use or dissemination is prohibited. IFP Energies nouvelles should not be liable for this message. Visitez notre site Web / Visit our web site : www.ifpenergiesnouvelles.fr / www.ifpenergiesnouvelles.com __________________________

6 10

Add repo for xfig package
by hersh parikh 18 Mar '11

18 Mar '11

Hi All We want to install packages like xfig and transfig on centos 5.5. We found rpms available but them but it seems there are lot of dependencies for these packages. So we would like to setup yum repo for this. Can anyone suggest trusted baseurl for yum repo? Regards Hersh

2 1

IPV6 - request for info
by Rajagopal Swaminathan 18 Mar '11

18 Mar '11

Greetings, I am trying to wrap my head around on this topic. Was wondering : Just as there is some scope for mapping ipv4 directly into IPV6 space, Is there a MAC ID or some kind of WWID has also been taken into consideration? Regards, Rajagopal

2 1

Re: [CentOS] security updates?
by Timothy Murphy 18 Mar '11

18 Mar '11

Sorin Srbu wrote: > Can we please, please, pretty please with a cherry on top, not start this > dance again? Don't you think there is something slightly farcical about posting messages suggesting people should stop posting messages? > V5.6 will be done when it's done, okay? I don't think the OP did ask when 5.6 would be ready. What he/she said, IIRC, was that Karanbir had suggested that 5.6 would be out last week, and he/she was asking if there had been a problem. This seems a perfectly reasonable question to me. Personally, I am very grateful to Karanbir and his accomplices for what I find an excellent OS, and I don't really care when 5.6 or 6 come out, as the present version works perfectly well for me. However, I don't think people who ask reasonable questions politely should be castigated for doing so. -- Timothy Murphy e-mail: gayleard /at/ eircom.net tel: +353-86-2336090, +353-1-2842366 s-mail: School of Mathematics, Trinity College, Dublin 2, Ireland

4 3

ssh remote execute awk problem
by sync 18 Mar '11

18 Mar '11

Hi , all : There is a problem on executing awk command to remote servers; The shell test script is like this : 1. #!/bin/sh 2. 3. _CMD="ssh root@localhost" 4. 5. cpu_num="$($_CMD awk '/processor/{count["proc"]++}; END{print count["proc"]}' /proc/cpuinfo)“ 6. 7. echo $cpu_num My root account can entry the server without the passwd. But I found no result on the screen . Is there some error on that script ? By the way , I googled and found use the following method can run the right result . 1. #!/bin/sh 2. 3. _CMD="ssh root@localhost" 4. 5. cpu_num="$($_CMD << 'HERE' 6. awk '/processor/{count["proc"]++}; END{print count["proc"]}' /proc/cpuinfo 7. HERE 8. 9. )“ 10. 11. echo $cpu_num

6 7

Re: [CentOS] security updates?
by m.roth＠5-cent.us 17 Mar '11

17 Mar '11

Sorin Srbu wrote: >>-----Original Message----- >>From: centos-bounces(a)centos.org [mailto:centos-bounces@centos.org] On >> Behalf >>Of Alain Péan >>Sent: Thursday, March 17, 2011 4:09 PM >>To: CentOS mailing list >>Subject: Re: [CentOS] security updates? >> >>May I ask the develloppers if we can have some update about the status >>of the release, why it was delayed (some problems ?), if if there is any >>schdule to release it ? > > Can we please, please, pretty please with a cherry on top, not start this > dance again? V5.6 will be done when it's done, okay? In the meantime, you're all > very free to use whatever other distro that has these updates, if you're so > antsy about them. Asking "when" won't speed things up, quite the contrary. > Please people... You beat me to it: *PLEASE* don't start this up again.... mark

7 11

Watching a directory
by Jason Slack-Moehrle 17 Mar '11

17 Mar '11

Hi All, I am thinking about an idea, but it requires that I be able to watch several directories for files that are added, deleted or maybe changed. Let start with adding files. What tools are available for me to watch a directory. In an example, if a file is added to a directory I want to run a shell script that will do some conversation on the file to produce a second copy. I have the shell scripting down, I am not sure how to watch, realize change and kick off the script with the parameters of the directory and what was added. Would anyone have thoughts? -Jason

7 6

security updates?
by Hendrik 17 Mar '11

17 Mar '11

Hello, There are several important security updates available: Critical: firefox security and bug fix update Important: tomcat5 security update Important: vsftpd security update Moderate: subversion security and bug fix update Important: logwatch security update Important: libtiff security update Moderate: kernel security and bug fix update Important: samba security update Important: samba3x security update Moderate: mailman security update Important: krb5 security update Moderate: postgresql security update Moderate: postgresql84 security update Moderate: pango security update Important: java-1.6.0-openjdk security and bug fix update Does CentOS not have any updates? -- Hendrik

3 2

tar exclude question
by Rainer Traut 17 Mar '11

17 Mar '11

Hi List, hope this is not too offtopic, but this bothers me and my backup. My backups are tar jobs in cron, eg: 20 23 * * * tar -zcf /mnt/backupInternalHosts/backup/backup.tar.gz /etc /root /home && touch /tmp/state_backup-backup This always sends me an unwanted email with: tar: Removing leading `/' from member names I consider this a bug because this informal message is printed to error out? Ok, I rewrite my tar job to get around this: tar -zc -f /mnt/backupInternalHosts/backup/backup.tar.gz -C / etc root home && touch /tmp/state_backup-backup Fine this works, but problems arise when I try to exclude things (example under /tmp/foo): $ mkdir dir1 dir2 dir1/dir2 $ touch dir1/dir2/importantFile $ tar -cvf tarfile.tar --exclude=dir2 -C /tmp/foo/ dir1 dir2 dir1/ Because the exclude pattern matches under dir1 my important File is not backed up. The problem is, I cannot specify the exclude pattern to match only /tmp/foo/dir2 , can I? Thx Rainer

8 10

Virtual Machine Manager Doesn't see vmx flag
by David McGuffey 17 Mar '11

17 Mar '11

Finished installing CentOS 5.5 x86_64 on a new Dell tower workstation that has a quad core Intel processor and 8 GB of ram. BIOS has hardware virtualization support enabled. /proc/cpuinfo shows that all four cores have the vmx flag present. I applied a lot of the National Security Agency guide for securing Red Hat Linux 5, testing the key applications I need as I went. At the end of the process I bring up VMM and it claims that the hardware doesn't support full virtualization. I'm going to go back through the NSA guide today looking for settings that might have an impact. My goal is to find and back out 1 or more settings rather than start from scratch with a full reload. Any ideas where I should focus my efforts? Dave M

3 4

perl one-liner issue
by Joseph L. Casale 17 Mar '11

17 Mar '11

I am trying to deduce the one liner for an rpm I am packaging to edit a php configuration file from within my spec. The line I am editing looks like: $conf['nagios_base'] = "/nagios/cgi-bin"; What are the escape requirements Perl needs from within the shell to search for this? As I have seen, the syntax is a mess, any pointers would be appreciated! thanks, jlc

6 8

CentOS 5.5 does not recognise SAS drives with LSI 1068E Controller
by Peter Peltonen 17 Mar '11

17 Mar '11

I need to do a new CentOS net install on a new server having the Supermicro X7DVL-3 motherboard: http://www.supermicro.com/products/motherboard/xeon1333/5000V/X7DVL-3.cfm Based on that info I assume the board having a "8x SAS Ports via LSI 1068E Controller". We received the server with 3 drives + 1 spare as hw RAID-5 preinstalled. During bootup I see that the drives are initialised and everything seems ok. The issue I am facing is that when trying to install CentOS no hard drives are recognised. I am a bit confused as others have reported CentOS 5.3 and 5.4 working "out of the box" with the same controller: http://www.linux-archive.org/centos/287219-installing-centos-5-4-64bit-serv… So I assumed that the megaraid_sas driver shipped with CentOS should support the controller? What confuses me also is the output of lspci: MegaRAID SAS 3208 ELP Does this mean its not the 1068E controller inside but something else? Or CentOS misidentifies it? So I assume the controller is not supported and I need a binary driver for it. For 1068e it should be: http://www.lsi.com/storage_home/products_home/standard_product_ics/sas_ics/… and the driver I need is inside the file mptlinux-4.26.00.00-1-rhel5.5.x86_64.dd.gz But how do I go applying this driver during installation as the server has no floppy drive? And what happens if I get the driver installed and then the server's kernel is updated? Do I need reinstall the driver somehow? Best regards, Peter

13 32

skype?
by m.roth＠5-cent.us 17 Mar '11

17 Mar '11

Well, at the urging of a friend who wants to talk face-to-face, I tried to install skype to my system at home (current CentOS 5.5). Got the fedora rpm; yum installed a library, then localinstalled skype, which is the current 2.1 beta. ldd shows an entry to linux-gate, which I don't have installed (or at least rpm tells me I don't). I try to run skype, and it complains about the version of glibc, even though I do have libstdc++.so.6. So, does anyone have any suggestions on a) how to get 2.1 beta working, or b) where I can find the *non* beta previous version...? Thanks in advance. mark "clues for the poor!"

4 3

Epel and yum downgrade : possible ?
by Philippe Naudin 16 Mar '11

16 Mar '11

Hello, Is it possible to downgrade to an old version of a package on epel ? I am in troubles with the new dokuwiki-0-0.6.20101107.a.el5, and cannot find dokuwiki-0-0.4.20091225.c.el5.noarch... Thanks, -- Philippe

5 6

Re: [CentOS] Mumble gamers' VOIP server (murmur)
by Michael Simpson 16 Mar '11

16 Mar '11

On 15 March 2011 19:07, Kenneth Porter <shiva(a)sewingwitch.com> wrote: > > BTW, I found that the initscript included in the Fedora RPM launches the > server as root instead of mumble-server (unprivileged user) and murmur must > drop privs once started. This causes the log file and sqlite DB to be > created owned by root, which causes problems later. The fix is to use the > --user option in the initscript. I need to cut another SRPM to address that. > I suppose that if you are using the default non-privileged port then there is no reason to start as root then drop to mumble-server user. I don't see this behaviour in the mandriva rpm files that i cut out and used. Next stop is getting SELinux to play nicely with it. It is also just another bit of software that i have to track manually though would be much happier to have it in the RPM database as my "check for updates" bookmarked tab group is getting longer and more painful to use. mike

1 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss