- Discuss - lists.centos.org

evbug module on centos 5
by Jerry Geis 29 Jun '07

29 Jun '07

How can I get the module evbug under centos 5? I was hoping it was there by default but it is not. Can I individually compile it? If so how. I havent done kernel modules before. evbug gives me all keyboard events in syslog. I tries a couple other keyloggers but it only gave me ps/2 keys not USB keys. Thanks, I am hoping evbug will give both ps/2 and USB keys. Jerry

1 0

centos drbd - mounts/ replication
by Karl R. Balsmeier 29 Jun '07

29 Jun '07

Hi, I would normally post this to the drbd list but it so low traffic/low volume (plus Austria might be asleep right now) I figured i'd ask someone here in case they have gotten drbd working on centos. Right now my system says i'm only the 971st person to even install it... It's been out for years, so likely this just means version 8. But you'll only see a couple of posts a day on there so far. Here's a "HOWTO" for getting things to a point where you can experiment carefully with the mounting procedures, which is where the mystery comes into view for the uninitiated <so don't follow it for production just yet, it's under construction for eventual use by the Wiki if we can answer some questions>: Install Centos 5 during install make a filesystem called /drbd-netblock and give it 1GB and it shows up as /dev/sda7 yum install drbd kmod-drbd edit /etc/grub.conf to allow boot of the drbd kernel 2.6.18-8.1.6.el5 #1 SMP reboot, the proper kernel should now be up. modprobe drbd umount /drbd-netblock filesystem so drbd can use it: umount /drbd-netblock edit /etc/drbd.conf /dev/sda7 is a 1GB filesystem I made during install called /drbd-netblock ############# global { usage-count yes; } common { syncer { rate 10M; } } resource r0 { protocol C; net { cram-hmac-alg sha1; shared-secret "secretphrase"; } on box1.mydomain.com { device /dev/drbd1; disk /dev/sda7; address 192.168.1.2:7789; meta-disk internal; } on box2.mydomain.com { device /dev/drbd1; disk /dev/sda7; address 192.168.1.3:7789; meta-disk internal; } } ############## drbdadm create-md r0 # Is this done on just the primary or both? I did it on both. drbdadm up all you'll see: [root@ ~]# ps ax | grep drbd 18063 ? S 0:00 [drbd1_worker] 18069 ? S 0:00 [drbd1_receiver] 18070 ? S 0:00 [drbd1_asender] cat /proc/drbd will show both in secondary, as the drbd website howto shows, and you can promote a node to primary: drbdadm -- --overwrite-data-of-peer primary all [root@ ~]# cat /proc/drbd version: 8.0.3 (api:86/proto:86) SVN Revision: 2881 build by buildsvn@c5-x8664-build, 2007-05-23 14:07:33 1: cs:Connected st:Primary/Secondary ds:UpToDate/UpToDate C r--- ns:0 nr:0 dw:0 dr:0 al:0 bm:0 lo:0 pe:0 ua:0 ap:0 resync: used:0/31 hits:0 misses:0 starving:0 dirty:0 changed:0 My question is, when the howto says "The device is usable right away, go ahead and create a filesystem if you haven't already", what do they mean? What are the following steps to get replication working? I also made myself a 40GB partition called /replicated just in case I wanted to use that. How does the "device" statement in the .conf file (device /dev/drbd1;) relate to any actual filesystem element? None right, it's just a name you give your netblock correct? Is the "disk" statement (disk /dev/sda7;) referring to my 1GB filesystem space I created, that's what I should put right? When you do the mount, are you doing "mount /dev/drbd1 /drbd-netblock1" or "mount /dev/drbd1 /replicated" ? I figure someone here in the Centos crowd will have an answer(s) so we can create a Wiki HOWTO for this. :-) -krb

1 0

missing Nagios dependencies: how to fix on yum?
by RR 28 Jun '07

28 Jun '07

On CentOS, I am trying to "yum install nagios" (after adding the rpmforge repository), but every time I run it, I get this message, and am not sure quite what to do. [root@nagios-server ~]# yum install nagios Setting up Install Process Setting up repositories Reading repository metadata in from local files Parsing package install arguments Resolving Dependencies --> Populating transaction set with selected packages. Please wait. ---> Package nagios.i386 0:2.9-1.el5.rf set to be updated --> Running transaction check --> Processing Dependency: rtld(GNU_HASH) for package: nagios --> Processing Dependency: libc.so.6(GLIBC_2.4) for package: nagios --> Finished Dependency Resolution Error: Missing Dependency: rtld(GNU_HASH) is needed by package nagios Error: Missing Dependency: libc.so.6(GLIBC_2.4) is needed by package nagios I ran "yum install httpd gcc glibc glibc-common gd gd-devel" (just like the Nagios HOWTO) thinking that it would resolve the dependencies, but I still get these errors.

5 18

Missing libexif update for Centos5
by Bernd Bartmann 28 Jun '07

28 Jun '07

Hi, could it be that the libexif update to 0.6.13-4.0.2 for Centos5 somehow got forgotten? The updates for Centos4 were released nearly two weeks ago. In the meantime also lots of other updates showed up for both Centos4 and Centos5, but still no libexif update for Centos5. Best regards, Bernd.

2 1

Vim differences between C4 and C5
by Rick Barnes 28 Jun '07

28 Jun '07

I have installed CentOS 4.5 and 5 on 2 separate machines, and both have default installs of vim-enhanced on each of them. I noticed that I can get syntax highlighting as a regular user, sudo and as root in C4.5. In C5 I only get highlighting as a regular user. I diff'ed my /etc/vimrc files between each install there is no changes and neither root ~ has a .vimrc file. I had put "# vim: filetype=apache ts=4 sw=4 et" at the bottom of the apache conf file and it works great except when I 'sudo vim' or use root in c5. I tried :syntax on, as root and it didn't make a difference either. CentOS 5: $ rpm -qa vim* vim-common-7.0.109-3.el5.3 vim-minimal-7.0.109-3.el5.3 vim-enhanced-7.0.109-3.el5.3 CentOS 4: $ rpm -qa vim* vim-minimal-6.3.046-0.40E.7 vim-common-6.3.046-0.40E.7 vim-enhanced-6.3.046-0.40E.7 Is there something I am missing? Thanks, Rick

4 3

Re: [CentOS] How to add to EPEL wishlist?
by Radu-Cristian FOTESCU 28 Jun '07

28 Jun '07

> I went ahead and added gtk-qt-engine and kaffeine to the EPEL wishlist: > > http://fedoraproject.org/wiki/EPEL/WishList > > juk appears to be part of kdemultimedia-extras in F7 (only > kdemultimedia is available in CentOS/RHEL), so I added that as well. Thanks! Maybe KPowersave wouldn't hurt, see here how to build it, it however needs a newer m4 than provided by RHEL5 (available in SL5 though): http://listserv.fnal.gov/scripts/wa.exe?A2=ind0706&L=scientific-linux-users… R-C Be smarter than spam. See how smart SpamGuard is at giving junk email the boot with the All-new Yahoo! Mail at http://mrd.mail.yahoo.com/try_beta?.intl=ca

1 0

Re: [CentOS] How to add to EPEL wishlist?
by Radu-Cristian FOTESCU 28 Jun '07

28 Jun '07

> You need a Wiki account (FAS): > > http://fedoraproject.org/wiki/WikiEditing#head-3d4b8815f923a8f137fb466901ca… > > You can contact me if you like to get added to the EditGroup when > you've completed the process It was obvious that I would need an account, so I made one. It was less than obvious that it would be useless. It's only now that I've read the whole complexity of the process to be performed *before* someone could add you to the EditGroup -- it's so unbelievable for a poor civilian that I am that I feel like I am already at Gitmo! Here's what I could read one should do: 1. Complete the Contributor License Agreement, but this has prerequisite steps. 2. In order to do that, you have to create a SSH key. 3. You then have to create a GPG key. 4. You have to create a Fedora account (not a wiki account!). 5. For that, your GPG key should be published to hkp://pgp.mit.edu/. 6. Submit the form to apply for a Fedora account. 7. Request the Contributor License Agreement (CLA). 8. Edit it to agree with it, GPG-sign it, and send it back. 9. Only now you can contact someone from the EditGroup to ask for the right to edit the wiki page that holds the EPEL wishlist! To me, it would be simpler to apply to visit the Pentagon or the CIA! I am disgusted by the way the Fedora people handle all this stuff. Everyone knowing how a Bugzilla works, or even how a mailing list works, can easily find that much simpler ways were available to the public to be able to SUGGEST a few packages for inclusion in EPEL. When GNOME asked the public in August-Sept. 2006 what new game to add to GNOME games, before setting up the Usage Survey, a suggestion list was open. It was easy to add suggestions there, by simply creating a wiki account, no fuss added, no strings attached. Now I know I can't expect for *anything* from EPEL. I can only rely on what's already there, plus what we can find in centosplus, Dag, Karan, ATrpms, and a few others. I am shocked. R-C Ask a question on any topic and get answers from real people. Go to Yahoo! Answers and share what you know at http://ca.answers.yahoo.com

4 4

RE: [CentOS] Battery status indicator in CentOS 4.4
by Lanny Marcus 28 Jun '07

28 Jun '07

>Message: 17 >Date: Tue, 26 Jun 2007 19:22:09 +0100 >From: Andrew Allen <andy.allen(a)virgin.net> >Subject: [CentOS] Battery status indicator in CentOS 4.4 >Message-ID: <1182882129.4113.21.camel(a)Atlas4.localdomain> >I've got CentOS 4.4 installed on 3 machines - two laptops and a PC. >Only one, a HP Omnibook 900, shows the graphical battery status >indicator (in the bottom right of the screen), but the other laptop (a <snip> Andy: As someone previous mentioned, if you are using GNOME, there is an applet: (a) Right click on the panel (where you see Applications, Actions, etc.) (b) Select Add to Panel (an Add to Panel window appears) (c) Select Battery Charge Monitor (you will probably need to configure it). HTH. P.S. Please do not cross post!

1 0

trapping keystrokes
by Jerry Geis 28 Jun '07

28 Jun '07

Hi all, How do you trap key strobes in centos before they are handed off to an application? In X windows I dont care what app is running or which app has focus. I need to know what key is pressed. The key can still go on to the application that is fine. I just need to know what keys are being pressed. I have tried xbindkeys but depending on which app is running I may or may not get my keypress binding, I tried loadkeys but that only works on the console and not X. Any ideas? Thanks, Jerry

2 1

Heartbeat for Centos 5- Can't build RPMS or install prebuilt RPMS
by Dave Augustus 28 Jun '07

28 Jun '07

I am stuck. This is X86_64 platform. In the extras repos, there is the SRPMS for heartbeat along with the RPMS for it. I have downloaded both. But I can't build the RPMS from the SRPM as it fails compiling something in BUILD/heartbeat-2.0.8/lib/crm/pengine Additionally, I can't install the RPMS: rpm -Uvh heartbeat-2.0.8-3.el5.centos.i386.rpm heartbeat-2.0.8-3.el5.centos.x86_64.rpm heartbeat-pils-2.0.8-3.el5.centos.i386.rpm heartbeat-2.0.8-3.el5.centos.x86_64.rpm heartbeat-stonith-2.0.8-3.el5.centos.i386.rpm heartbeat-stonith-2.0.8-3.el5.centos.x86_64.rpm error: Failed dependencies: libperl.so is needed by heartbeat-2.0.8-3.el5.centos.i386 but perl is installed. Any ideas are greatly appreciated.

1 1

How to add to EPEL wishlist?
by Radu-Cristian FOTESCU 28 Jun '07

28 Jun '07

Does anyone know how to submit wishes to the EPEL Wishlist here? http://fedoraproject.org/wiki/EPEL/WishList It reads "Immutable Page". They say: "Please add packages that are part of Fedora but lack a EPEL maintainer to this list", but there is no way to do that! They don't say if "Packages part of Fedora" means "Core" or it can be Extras too, but packages obviously missing from RHEL (4 and 5) and castrating the KDE desktop include: -- JuK (it was stripped off kdemultimedia); -- Kaffeine; -- gtk-qt-engine; ... As a side note for AmaroK lovers: I am very happy with the simpler JuK on systems where I have it, and it *does* have a future, as it will be present in KDE4 too: http://www.purinchu.net/wp/2007/06/26/juk-love/ But Red Hat _hates_ KDE apps, and it even castrates official KDE packages such as kdemultimedia... Thanks, R-C __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

3 2

CentOS 5.0 suspend to disk (hibernate)
by roland_renaud＠mitel.com 28 Jun '07

28 Jun '07

The RHEL 5 release notes for their desktop version claim "Improved ACPI support with features such as suspend to disk" but this isn't working with CentOS 5. I've installed all the packages and updates for CentOS 5 i386 on a ThinkPad T43 but when selecting suspend, Gnome pops up a URL to a site that didn't seem to give a solution. Gnome makes an entry in /var/log/messages indicating that the suspend button was pressed, immediately followed by the "Resuming computer" message. Suspend to ram and suspend to disk work on Ubuntu 6.10 on this machine with an older kernel (2.6.17-10-generic) than CentOS 5 has. Are there some packages or a different kernel that should be installed? Will this feature be added to CentOS 5 or is it considered a server distro that doesn't need this? Thinkwiki.org mentions the swsusp program but it seems to be absent. CentOS 4 and CentOS 5 have been running well on this machine but having the suspend feature would be very nice. Thanks, and thanks to the team for making CentOS available. roland roland_renaud at Mitel.COM

5 11

AX25 kernel compile help
by Evans F. Mitchell; KD4EFM / AFA2TH / WQFK-894 28 Jun '07

28 Jun '07

Is there someone who can help me compile who can compile the latest kernel with ax25 and other item related to ROSE / NETRom ect. stuff for a project I am working on? I have looked at Knoppix and what not but the kernel seems to be out of date a little. I like the looks and feel of the centos format and the GUI's that CentOS has and wanted to test it out in the Amateur Radio realm. Thanks Evans F. Mitchell KD4EFM / AFA2TH FL; USAF MARS GMRS: WQFK894 D-STAR 145.670 Simplex WCF Section ARRL Member ARRL WCF Section Web Site http://www.arrlwcf.org Polk County ARES Web site http://www.polkemcomm.org <kd4efm hotmail com> alt box

1 0

CentOS-announce Digest, Vol 28, Issue 19
by centos-announce-request＠centos.org 28 Jun '07

28 Jun '07

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CESA-2007:0533 Moderate CentOS 3 i386 httpd - security update (Tru Huynh) 2. CESA-2007:0533 Moderate CentOS 3 x86_64 httpd - security update (Tru Huynh) 3. CESA-2007:0605 Critical CentOS 4 x86_64 HelixPlayer - security update (Johnny Hughes) 4. CESA-2007:0605 Critical CentOS 4 i386 HelixPlayer - security update (Johnny Hughes) ---------------------------------------------------------------------- Message: 1 Date: Wed, 27 Jun 2007 17:34:54 +0200 From: Tru Huynh <tru(a)centos.org> Subject: [CentOS-announce] CESA-2007:0533 Moderate CentOS 3 i386 httpd - security update To: centos-announce(a)centos.org Message-ID: <20070627153454.GB12008(a)sillage.bis.pasteur.fr> Content-Type: text/plain; charset="us-ascii" CentOS Errata and Security Advisory CESA-2007:0533 httpd security update for CentOS 3 i386: https://rhn.redhat.com/errata/RHSA-2007-0533.html The following updated file has been uploaded and is currently syncing to the mirrors: i386: updates/i386/RPMS/httpd-2.0.46-67.ent.centos.i386.rpm updates/i386/RPMS/httpd-devel-2.0.46-67.ent.centos.i386.rpm updates/i386/RPMS/mod_ssl-2.0.46-67.ent.centos.i386.rpm source: updates/SRPMS/httpd-2.0.46-67.ent.centos.src.rpm You may update your CentOS-3 i386 installations by running the command: yum update httpd\* mod_ssl Tru -- Tru Huynh (CentOS-3 i386/x86_64 Package Maintenance) http://pgp.mit.edu:11371/pks/lookup?op=get&search=0xBEFA581B

1 0

Re: [CentOS] How to add to EPEL wishlist?
by Radu-Cristian FOTESCU 28 Jun '07

28 Jun '07

> Wrong list? The subject line was a question. EPEL stands for... you know what. And CentOS is a rebuild of... you know what. Therefore, I suspect that CentOS users would/should/could be interested in adding EPEL as an extra repository. You know, there is more than Karan[bir] and DAG on Earth... But yes, it might be a wrong list, for different reasons than you thought of. R-C __________________________________________________ Do You Yahoo!? Tired of spam? Yahoo! Mail has the best spam protection around http://mail.yahoo.com

2 1

Vsftpd problem
by Tony Molloy 28 Jun '07

28 Jun '07

Hi all, I have a filesystem which I need to make available through ftp ( vsftpd ). I have this as separate filesystem as it needs to be available through apache and NFS also. It's our local mirror. I've set up vsftpd and put a test directory in /var/ftp/pub and it works. However I can't seem to get it to see the separate /mirrors filesystem. I've tried using symlinks as below in /var/ftp/pub. drwxr-xr-x 3 root root 4096 Jun 26 10:53 . drwxr-xr-x 3 root root 4096 Jun 22 12:11 .. -rw-r--r-- 1 root root 25 Jun 22 12:21 .message drwxr-xr-x 2 root root 4096 Jun 22 15:25 TEST lrwxrwxrwx 1 root root 8 Jun 26 10:53 mirrors -> /mirrors I this case the TEST directory works but the mirrors directory does not. ftp> cd mirrors 550 Failed to change directory. I've also tried using mount --bind to remount the the /mirrors filesystem as /var/ftp/pub/mirrors. When I do this I can see the contents of /var/ftp/pub/mirrors drwxr-xr-x 2 root root 4096 Jun 22 15:25 TEST drwxr-xr-x 13 root root 4096 Jun 23 07:54 mirrors ls -al /var/ftp/pub/mirrors/ drwxr-xr-x 13 root root 4096 Jun 23 07:54 . drwxr-xr-x 4 root root 4096 Jun 26 11:04 .. drwxr-xr-x 9 1000 1000 4096 May 18 00:19 centos drwxr-xr-x 6 ftp 803 4096 Mar 15 13:11 config-linux drwxr-xr-x 4 apache apache 4096 Sep 21 2006 custom-repos However when I try to ftp to it I can't see the mirrors directory -rw-r--r-- 1 ftp ftp 25 Jun 22 12:21 .message drwxr-xr-x 2 ftp ftp 4096 Jun 22 15:25 TEST Finally I've tried mounting it directly under /var/ftp/pub/mirrors -rw-r--r-- 1 root root 25 Jun 22 12:21 .message drwxr-xr-x 2 root root 4096 Jun 22 15:25 TEST drwxr-xr-x 13 root root 4096 Jun 23 07:54 mirrors But when I ftp into the box again I can't see the mirrors directory ftp> ls 227 Entering Passive Mode (10,220,1,157,168,142) 150 Here comes the directory listing. drwxr-xr-x 2 ftp ftp 4096 Jun 22 15:25 TEST 226 Directory send OK. Is this a permissions problem or does vsftpd not allow separate filesystems to be seen. Regards, Tony

3 6

snmpd log messages
by Paul R. Ganci 28 Jun '07

28 Jun '07

I updated to CentOS 4.5 yesterday and now I am finding the snmpd daemon is logging reams and reams of these messages: May 20 10:40:03 mx01 snmpd[2572]: Connection from - 127.0.0.1 May 20 10:40:03 mx01 snmpd[2572]: transport socket = 12 Is there a way to turn off this useless logging? I am getting these every 5 minutes (every time MRTG updates my MailScanner statistics). So far what I tried was to take off the -a switch when starting snmpd. That didn't help. This snmpd behavior is new from CentOS 4.4. -- Paul (ganci(a)nurdog.com)

5 7

Firefox and Thunderbird 2.0, Centos 5, and rpms
by Robert Moskowitz 27 Jun '07

27 Jun '07

I am making some progress on my Centos 5 notebook build. So I am looking at Firefox and Thunderbird 2.0. Should I install them? Or is Redhat correct that there is nothing improved here and wait for 3.0? (well I have not even had a chance to look at Thunderbird 2.0, that is new)? I have the install steps we covered here back on 2/2/07; but are there rpms? I did not find anything over at ATrpms. Some advice would be greatly appreciated.

10 12

empty /var/log/messages
by beast 27 Jun '07

27 Jun '07

I have one centos 4.0 server which /var/log/messages was always empty (0 bytes). I wonder what has been blocking the syslog to write the log. Other (syslog) log files are fine, only messages. /etc/syslog.conf: # Log anything (except mail) of level info or higher. # Don't log private authentication messages! *.info;mail.none;authpriv.none;cron.none;spampd.none -/var/log/messages .thanks

7 10

one application receive all key commands
by Jerry Geis 27 Jun '07

27 Jun '07

Is there a way in centos 4 or 5 to have one application receive all keyboard events - no matter what is running. Some applications bind keys etc... and I need to get those keys no matter what and not have the application see them at all. Is there a way to do that? Jerry

1 0

logwatch reports not benig emailed
by Kanwar Ranbir Sandhu 27 Jun '07

27 Jun '07

Hello, I have a couple of CentOS 5 servers, and third running in a FC6 domU. I've configured postfix on those servers to not deliver any email to the local system, but to instead relay mail to an internal mail server. I also set up /etc/aliases to send all mail to root to me, ksandhu. I can send mail on the command line, and I get it at my email address, delivered to the internal mail server: great! But, every night when logwatch runs, the damned reports never make it to my mailbox. What's worse is that I can manually run logwatch (logwatch --mailto root), and I get the report in my mailbox! All CentOS 5 servers are exhibiting the same behaviour. I've setup postfix like I always have. CentOS 4 servers with the same config are sending their logwatch reports properly. I've tried explicitly setting the path to sendmail in /etc/logwatch/conf/logwatch.conf: mailer = "/usr/sbin/sendmail -t" but, it hasn't helped. Does anyone have any ideas? I must be missing something obvious. Regards, Ranbir -- Kanwar Ranbir Sandhu Linux 2.6.20-1.2944.fc6 i686 GNU/Linux 12:14:54 up 16 days, 3:01, 3 users, load average: 0.99, 0.38, 0.23

4 5

OpenCA for Centos
by Robert Moskowitz 27 Jun '07

27 Jun '07

OpenCA has rpm for FC4: https://www.openca.org/projects/openca/downloads.shtml Will that work for Centos 5? Gee I should just spin up a box, try it and see if it crashes and burns....... Given the interest in OpenCA in edu and k-12, it would be nice to see this readily available. Of course I am biased, as I lurk on the various edu PKI forum.

1 0

Re: [CentOS] Re: empty /var/log/messages
by David G. Miller 27 Jun '07

27 Jun '07

On Tuesday 26 June 2007, beast wrote: > > On 26/06/07 13:42 +0100, Seán O Sullivan wrote: > >>>> > >>> I have one centos 4.0 server which /var/log/messages was always >>>> > >>> empty (0 bytes). I wonder what has been blocking the syslog to write >>>> > >>> the log. >>>> >>> > >> >>> > >> Firstly, I'd suggest updating to 4.5. >>> > > > > This is the production machine and has been runing for years, so > > upgrading OS is not not my first option :) > > > >>> > >> Secondly, is /tmp mounted with noexec option? >>> > > > > No afaik. > > > > root# mount | grep var > > /dev/hda4 on /var type ext3 (rw) > > > >> > >forgot to add, check /var/log/messages.* for current syslog messages >> > > > > root# ls -l messages* > > -rw------- 1 root root 0 Jun 25 11:11 messages > > -rw------- 1 root root 32480831 Jun 3 00:04 messages.1.gz > > -rw------- 1 root root 81601061 May 27 00:13 messages.2.gz > > -rw------- 1 root root 905460 May 20 00:01 messages.3.gz > > -rw------- 1 root root 1055604 May 13 00:01 messages.4.gz > > > > Note: previous messages.gz was having gigantic size because recent bug > > in spamassassin, it logs all spampd log thats why I disable it on the > > syslog.conf. But after few days I notice that messages were always > > empty, even I restart syslog and then mv and touch messages > > > >From my own experience there is one trivial way to cause this. How much space is left on whatever partition /var is mounted on? Your comment about SA causing the huge log reminded me of the time I filled /var due to spewage from a bad configuration. Cheers, Dave -- Politics, n. Strife of interests masquerading as a contest of principles. -- Ambrose Bierce

1 0

CentOS5 on Dell Latitude D620, Docking Station & Dual Monitors???
by Matt Shields 27 Jun '07

27 Jun '07

I've got a Dell Latitude D620, dell docking station and a Dell 2007WFP (20" widescreen lcd). With XP I had the laptop screen and the lcd working as dual screens. But for the life of me I cannot get CentOS5 to work with dual screens. Anyone have this working? I would greatly appreciate any assistance. -matt

2 3

CentOS-announce Digest, Vol 28, Issue 18
by centos-announce-request＠centos.org 27 Jun '07

27 Jun '07

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CESA-2007:0384 Critical CentOS 3 i386 krb5 - security update (Tru Huynh) 2. CESA-2007:0384 Critical CentOS 3 x86_64 krb5 - security update (Tru Huynh) 3. CESA-2007:0532-01: Moderate CentOS 2 i386 apache security update (John Newbigin) 4. CESA-2007:0384-01: Critical CentOS 2 i386 krb5 security update (John Newbigin) 5. CESA-2007:0509 Important CentOS 4 i386 evolution - security update (Johnny Hughes) 6. CESA-2007:0509 Important CentOS 4 x86_64 evolution - security update (Johnny Hughes) 7. CESA-2007:0488 Important CentOS 4 x86_64 kernel - security update (Johnny Hughes) 8. CESA-2007:0488 Important CentOS 4 i386 kernel - security update (Johnny Hughes) 9. CESA-2007:0562 Important CentOS 4 i386 krb5 - security update (Johnny Hughes) 10. CESA-2007:0562 Important CentOS 4 x86_64 krb5 - security update (Johnny Hughes) 11. CESA-2007:0534 Moderate CentOS 4 x86_64 httpd - security update (Johnny Hughes) 12. CESA-2007:0534 Moderate CentOS 4 i386 httpd - security update (Johnny Hughes) 13. CESA-2007:0510 Important CentOS 5 i386 evolution-data-server - security update (Johnny Hughes) 14. CESA-2007:0510 Important CentOS 5 x86_64 evolution-data-server - security update (Johnny Hughes) 15. CESA-2007:0562 Important CentOS 5 x86_64 krb5 - security update (Johnny Hughes) 16. CESA-2007:0562 Important CentOS 5 i386 krb5 - security update (Johnny Hughes) 17. CESA-2007:0556 Moderate CentOS 5 i386 httpd - security update (Johnny Hughes) 18. CESA-2007:0556 Moderate CentOS 5 x86_64 httpd - security update (Johnny Hughes) ---------------------------------------------------------------------- Message: 1 Date: Tue, 26 Jun 2007 22:37:06 +0200 From: Tru Huynh <tru(a)centos.org> Subject: [CentOS-announce] CESA-2007:0384 Critical CentOS 3 i386 krb5 - security update To: centos-announce(a)centos.org Message-ID: <20070626203706.GB23911(a)sillage.bis.pasteur.fr> Content-Type: text/plain; charset="us-ascii" CentOS Errata and Security Advisory CESA-2007:0384 krb5 security update for CentOS 3 i386: https://rhn.redhat.com/errata/RHSA-2007-0384.html The following updated file has been uploaded and is currently syncing to the mirrors: i386: updates/i386/RPMS/krb5-devel-1.2.7-66.i386.rpm updates/i386/RPMS/krb5-libs-1.2.7-66.i386.rpm updates/i386/RPMS/krb5-server-1.2.7-66.i386.rpm updates/i386/RPMS/krb5-workstation-1.2.7-66.i386.rpm source: updates/SRPMS/krb5-1.2.7-66.src.rpm You may update your CentOS-3 i386 installations by running the command: yum update krb5\* Tru -- Tru Huynh (CentOS-3 i386/x86_64 Package Maintenance) http://pgp.mit.edu:11371/pks/lookup?op=get&search=0xBEFA581B

1 0

Need to do some careful moving...
by Robert Moskowitz 27 Jun '07

27 Jun '07

When I built this new Centos 5 drive, I copied over much of my old data using cp, and did not use the -preserve option. Ouch. I need those file create dates so that documents and such sort properly, historically. I recovered much of my stuff from a tar built back in mid-May (but I missed that the tar backup ended abnormally, as I was tar-ing to a USB attached drive formatted FAT32, and at 4Gb, it stopped). Now I want to copy all of my newer files into this recovered directory. The -u option of cp and mv will do the wrong thing, of course. I want to only copy files that are NOT present in the recovered directory. I will of course still be stuck with a lot of files with a Jun 18 date that were created between the backup date and Jun 18, but at least I will be better off.... Perhaps I do a mv -f from the recovered to the misdated directory? Being careful to protect those few files that HAVE really been modified since the backup? Oh, I am talking about 30k files here.....

2 1

CentOS 5 & USB Kickstart?
by Jiann-Ming Su 26 Jun '07

26 Jun '07

Is anybody else having problems with CentOS 5 not loading the usb drivers for kickstart installations? I'm passing "linux ks=hd:sdb1:/ks.cfg," but I get a message saying it can't find the ks.cfg file and I should enter another path. I use the exact same boot options with CentOS 4 without any problems. What am I missing with CentOS 5? Thanks for any tips. -- Jiann-Ming Su "I have to decide between two equally frightening options. If I wanted to do that, I'd vote." --Duckman "The system's broke, Hank. The election baby has peed in the bath water. You got to throw 'em both out." --Dale Gribble "Those who vote decide nothing. Those who count the votes decide everything." --Joseph Stalin -- Jiann-Ming Su "I have to decide between two equally frightening options. If I wanted to do that, I'd vote." --Duckman "The system's broke, Hank. The election baby has peed in the bath water. You got to throw 'em both out." --Dale Gribble "Those who vote decide nothing. Those who count the votes decide everything." --Joseph Stalin

3 3

TinyCA2 on rpmforge EL4 but not EL5
by Robert Moskowitz 26 Jun '07

26 Jun '07

I want to install TinyCA2 on my Centos5 setup. I had a real learning experience the last time around (last year, July) and in the end, I got the repo down from Dag's site and was cool. Now I am on Centos 5 and no TinyCA2. Can I just download the EL4 rpm from: http://apt.sw.be/redhat/el4/en/i386/dag/repodata/repoview/tinyca2-0-0.7.5-2… and do a yum localinstall ? Or do I have to wait for it to appear as an EL5 rpm?

3 2

Battery status indicator in CentOS 4.4
by Andrew Allen 26 Jun '07

26 Jun '07

I've got CentOS 4.4 installed on 3 machines - two laptops and a PC. Only one, a HP Omnibook 900, shows the graphical battery status indicator (in the bottom right of the screen), but the other laptop (a new Dell Inspiron 1501) doesn't show it. Furthermore, the command /usr/bin/apm gets the response 'no apm support in kernel' - I've tried yum-updating the kernel and installing apm but to no avail. Any suggestions please as it's obviously very useful/necessary to have a battery indicator! Andy

2 5

Troubles with CentOS5 and 3ware RAID controller
by Luc de Louw 26 Jun '07

26 Jun '07

Folks, Since approx. a half year I have run two servers with CentOS4, all was running very stable. Then I upgraded to CentOS5 (fresh install). The servers are running quite unstable since the upgrade. The system is freezing after short uptime. I suspect the driver for the 3ware controller, because I got such error messages: 3w-xxxx: scsi0: Character ioctl (0x1f) timed out, resetting card. 3w-xxxx: scsi0: Character ioctl (0x1f) timed out, resetting card. 3w-xxxx: scsi0: Character ioctl (0x1f) timed out, resetting card. (lots of repeats of this messages) sd 0:0:0:0: rejecting I/O to offline device sd 0:0:0:0: rejecting I/O to offline device sd 0:0:0:0: rejecting I/O to offline device EXT3-fs error (device sda6): ext3_find_entry: reading directory #2 offset 0 sd 0:0:0:0: rejecting I/O to offline device sd 0:0:0:0: rejecting I/O to offline device sd 0:0:0:0: rejecting I/O to offline device After some time (few hours) the systems are completely freezing, no display of errors on the console or logs Here some relevant data of my system: 00:0a.0 RAID bus controller: 3ware Inc 7xxx/8xxx-series PATA/SATA-RAID (rev 01) Subsystem: 3ware Inc 7xxx/8xxx-series PATA/SATA-RAID Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR- FastB2B- Status: Cap+ 66MHz+ UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 32 (2250ns min), Cache Line Size: 32 bytes Interrupt: pin A routed to IRQ 185 Region 0: I/O ports at e100 [size=16] Region 1: Memory at fa824000 (32-bit, non-prefetchable) [size=16] Region 2: Memory at fa000000 (32-bit, non-prefetchable) [size=8M] [virtual] Expansion ROM at 80060000 [disabled] [size=64K] Capabilities: [40] Power Management version 1 Flags: PMEClk- DSI- D1+ D2- AuxCurrent=0mA PME(D0-,D1-,D2-,D3hot-,D3cold-) Status: D0 PME-Enable- DSel=0 DScale=0 PME- Kernel: 2.6.18-8.1.6.el5 It cannot be a 3ware hardware error, because the controller was exchanged with the same results afterwards. Any hints are very welcome. Thanks, Luc

2 1

ext3 and acls
by Dave 26 Jun '07

26 Jun '07

Hello, I've got a centos5 box with raided ext3 partitions mp* devices. I'm wondering if ext3 supports acls out of the box or if there's something i have to do to enable them? Thanks. Dave.

4 3

vncviewer package wit hcentos 5
by Jerry Geis 26 Jun '07

26 Jun '07

I have xkeybindings running just fine on centos 5. I have vncviewer running in full screen mode showing another PC. When vncviewer is running is running it seems to override my xkeybindings. Is there a way to tell vncviewer to not bind to any keys?? The only keys I am binding is on the Keypad 3,4,6, 9 and Enter. Nothing that vncviewer uses anyway. How can I still have my xkeybindings active with vncviewer running? Thanks, Jerry

1 0

Wireless networking in CentOS 4.4
by Andrew Allen 26 Jun '07

26 Jun '07

Trying to set up wireless networking with CentOS 4.4 on a (new Dell) laptop and have looked at http://www.ces.clemson.edu/linux/fc2- ipw2200.shtml and http://www.centos.org/modules/newbb/viewtopic.php? topic_id=2532&forum=30 regarding use of ipw2200, which is included in the kernel. The problem is that it doesn't appear to be actually installed/loaded because the Intel Corporation PRO/Wireless 2200BG driver doesn't appear in the drop- down list under Devices > New > Wireless Connection in system-config- network. Also /sbin/lsmod | grep ipw doesn't produce anything - so I'm pretty baffled! Any suggestions please? Andy

2 1

Getting JPilot working
by Robert Moskowitz 26 Jun '07

26 Jun '07

I am trying to get JPilot working. I have configed gnome-pilot-applet, but it is not talking to the USB connected Treo650. My Treo has my name as the user, so from the applet, I see also a userid (my UID on this system it seems). I try to put that on the Treo and nothing happens. I have enabled the Backup Conduit. I am using /dev/pilot, which shows up when my Treo is connected via its USB syncing cable. In JPilot in settings, I specify /dev/pilot I go install user and install the same user as in the pilot-applet. I click on sync and press the sync button on the cable and I watch all the files get backed up to my /MyPilot directory (used from pilot-applet). But NOTHING shows up in J-Pilot. Everything is still there on the Treo.... Any thoughts? /var/log/messages shows the following in conjunction with a Sync: Jun 26 10:55:24 nc4010 kernel: usb 1-2: new full speed USB device using ohci_hcd and address 11 Jun 26 10:55:24 nc4010 kernel: usb 1-2: configuration #1 chosen from 1 choice Jun 26 10:55:24 nc4010 kernel: visor 1-2:1.0: Handspring Visor / Palm OS convert er detected Jun 26 10:55:24 nc4010 kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB0 Jun 26 10:55:24 nc4010 kernel: usb 1-2: Handspring Visor / Palm OS converter now attached to ttyUSB1 Jun 26 10:55:47 nc4010 kernel: usb 1-2: USB disconnect, address 11 Jun 26 10:55:47 nc4010 kernel: visor 1-2:1.0: device disconnected Sync runs nicely, the files on the Treo are backed up to the director specified in

1 1

CentOS5: Eclipse error!
by Antonio da Silva Martins Junior 26 Jun '07

26 Jun '07

Hello, We had a CentOS5 server with Eclipse on it, one of our programmers tried to update the Eclipse install (within eclipse) and after a problem on the update it stop working. I tried removing the Eclipse RPMs and eclipse directories, and reinstalling it with yum. Now we had this error, on $HOME/workspace/.metadata/.log: !SESSION 2007-06-25 09:44:00.093 ----------------------------------------------- eclipse.buildId=M20060921-0945 java.version=1.6.0_01 java.vendor=Sun Microsystems Inc. BootLoader constants: OS=linux, ARCH=x86_64, WS=gtk, NL=pt_BR Command-line arguments: -os linux -ws gtk -arch x86_64 !ENTRY org.eclipse.update.configurator 2007-06-25 09:44:01.535 !MESSAGE Could not install bundle plugins/org.eclipse.pde.build/ Bundle "org.e clipse.pde.build" version "3.2.1.r321_v20060823" has already been installed from : update(a)plugins/org.eclipse.pde.build_3.2.1.r321_v20060823/ !ENTRY org.eclipse.core.runtime 2007-06-25 09:44:02.208 !MESSAGE Product org.eclipse.sdk.ide could not be found. The error go on... Somebody had an idea on what are this "already installed" update, on this way I can wipe all the install and put it fresh from the repository! Thanks in advance, Antonio. -- +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ | Antonio S. Martins Jr. - Support Analist | "Only The Shadow Knows | | Universidade Estadual de Maringá - Brasil| what evil lurks in the | | NPD - Núcleo de Processamento de Dados | Heart of Men!" | | E-Mail: asmartins(a)uem.br / shadow(a)uem.br | !!! Linux User: 52392 !!! | +-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+-+ -- Esta mensagem foi verificada pelo sistema de antiv�rus e acredita-se estar livre de perigo.

1 0

CentOS-announce Digest, Vol 28, Issue 17
by centos-announce-request＠centos.org 26 Jun '07

26 Jun '07

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CESA-2007:0509 Important CentOS 3 i386 evolution - security update (Tru Huynh) 2. CESA-2007:0509 Important CentOS 3 x86_64 evolution - security update (Tru Huynh) ---------------------------------------------------------------------- Message: 1 Date: Mon, 25 Jun 2007 16:45:34 +0200 From: Tru Huynh <tru(a)centos.org> Subject: [CentOS-announce] CESA-2007:0509 Important CentOS 3 i386 evolution - security update To: centos-announce(a)centos.org Message-ID: <20070625144534.GA23811(a)sillage.bis.pasteur.fr> Content-Type: text/plain; charset="us-ascii" CentOS Errata and Security Advisory CESA-2007:0509 evolution security update for CentOS 3 i386: https://rhn.redhat.com/errata/RHSA-2007-0509.html The following updated file has been uploaded and is currently syncing to the mirrors: i386: updates/i386/RPMS/evolution-1.4.5-21.el3.i386.rpm updates/i386/RPMS/evolution-devel-1.4.5-21.el3.i386.rpm source: updates/SRPMS/evolution-1.4.5-21.el3.src.rpm You may update your CentOS-3 i386 installations by running the command: yum update evolution\* Tru -- Tru Huynh (CentOS-3 i386/x86_64 Package Maintenance) http://pgp.mit.edu:11371/pks/lookup?op=get&search=0xBEFA581B

1 0

2007 New Zealand Open Source Awards
by Johnny Hughes 26 Jun '07

26 Jun '07

Anyone using CentOS to do open source things in New Zealand? If so ... nominate yourself here for the 2007 New Zealand Open Source Awards. The best I can tell ... New Zealanders are the organizations / people they want for nominees. The CentOS Project has no (to my knowledge) developers in New Zealand, but if some of the organizations there are using the product, maybe they can nominate themselves and CentOS for awards in some of the categories. http://www.nzosa.org.nz/ Thanks, Johnny Hughes

1 0

bind on centos 5
by Indunil Jayasooriya 26 Jun '07

26 Jun '07

Hi, I am trying to setup bind on centOS 5. But there are no files coming by default. But I found some files @ /usr/share/doc/bind-9.3.3/sample Now, could you pls tell me what r the files I need to set it up? Is there are a good doc on How to setup dns on CentOS 5 ? -- Thank you Indunil Jayasooriya

5 5

rpmrebuild or rpmbuild question
by centos 26 Jun '07

26 Jun '07

Hello I have compiled php on a server, but want to upgrade and recompile it with new features. is rpmbuild or rpmrebuild capable of compiling or adding these new features ? or I should download the source and run ./configure again ? what about yum ? it was great if yum or rpmbuild could save the current config and just add the new extensions. Thanks

3 5

Centos 5.0 x86-64 install crashes with Realtek 8111B Ethrenet
by Richard Chapman 26 Jun '07

26 Jun '07

While installing Centos 5.0 x86-64 on a Gigabyte GA-945GM-S2 motherboard which has Realtek 8111B Ethernet chip - Anaconda crashes. I select the option to use the Centos online repository for extra packages - I am asked to enter IP address etc. The drop box to select the Ethernet interface is blank. If I enter valid IP address and gateway - anaconda crashes and the system reboots from CD. I think that the NIC chip is not correctly detected by anaconda - and there must be a problem in the logic which allows anaconda to try to connect to the network without any available network adaptor. Incidentally - I also use a version of Linux called Trinity Rescue. The current version of trinity used kernel 2.6.19.2 - and this detects and runs the same Ethernet chip fine. Maybe the newer kernel fixes the problem - or maybe the problem is specific to x86-64 architecture. In Bug report 0001947 someone reports he fixed this problem with a new driver from realtek and/or redhat. I have downloaded this driver - but can anyone point me to instructions on how to compile and install it? I have built a Centos 5.0 without network support. Alternatively - does anyone know when we expect a Centos 5.1 release? Is there a beta I can get hold of before the release? Alternatively - can I download updates for the Centos 5 from a yum repository using a working cetos 4.4 installation - then use yum or rpm to install a new kernel or driver on the Centos 5.0 system? Can anyone suggest were I would find instructions on how to do this? Thanks Richard.

1 0

Exe file size is chaning during runtime
by balajisundar＠midascomm.com 26 Jun '07

26 Jun '07

Dear All, We have observed the exe file size getting changed during run time of the system in CentOS. We are using CentOS 4.4 release. We have taken "strings" of the original "exe" and changed "exe". Then we compared the strings output of the two. The difference is given below. We are not sure why this is happening. Can some one throw light on this. diff oldExeStrings newExeStrings 1a2,8 > MzFX# > PzFr > MzF` > MzFm > MzF% > MzFXi > MzF 163a171,182 > libssl.so.4 > libcrypto.so.4 > libkrb5.so.3 > libcom_err.so.2 > libcrypt.so.1 > libresolv.so.2 > libnsl.so.1 > libpthread.so.0 > /lib/ld-linux.so.2 > libgssapi_krb5.so.2 > libk5crypto.so.3 > libz.so.1 --Regards S.Balaji

3 4

ipmi regression in 4.5?
by Gavin Carr 26 Jun '07

26 Jun '07

I've been monitoring CPU temperature on a few Dell SC1435s running CentOS4 via OpenIPMI and 'ipmitool sdr'. It's been working very nicely, but the upgrade to 4.5 not so long ago seems to have broken something: # ipmitool sdr type Temperature Temp | 01h | ns | 3.1 | Disabled Planar Temp | 04h | ok | 7.1 | 30 degrees C Temp Interface | 53h | ns | 7.1 | Disabled The disabled sensors above used to work fine, and there have been no config changes or bios upgrades or anything. All machines affected post 4.5. Any suggestions? Cheers, Gavin

2 5

How can I set NIC duplex before installation?
by John Horne 26 Jun '07

26 Jun '07

Hello, I have installed CentOS 5 onto a server this afternoon using NFS. The NFS 'server' has a 100Mb/full-duplex interface, the server I installed CentOS on to has 4 x 100Mb interfaces. However, the installation was painfully slow to start with, and by using ctrl-alt-f2/f4/f5 I could see that contact with the NFS server was intermitently failing. Soon after some of the packages had installed the 'ethtool' command was then available, and I could see that the (installation) server NIC had been set to 100Mb but at half-duplex. This was causing numerous collisions and errors on the NIC interface. As soon as I reset the NIC to full-duplex (via ctrl-alt-f2 and using ethtool), then the installation speeded up and seemed to cause no more errors. My question is, how can I tell anaconda to set the NIC interface options such as speed and duplex? I have another server to install which has 2 x gigabit NICs and 2 x 100MB NIC's. My concern is that anaconda will again use wrong NIC parameters, and the installation will again be very slow. Surely it is possible to set the NIC options? John. -- --------------------------------------------------------------- John Horne, University of Plymouth, UK Tel: +44 (0)1752 233914 E-mail: John.Horne(a)plymouth.ac.uk Fax: +44 (0)1752 233839

3 4

yum version of Debian's sources.list?
by RR 25 Jun '07

25 Jun '07

I'm hoping to find the CentOS version of Debian's /etc/apt/sources.list "yum install program" isn't running properly on one server, and I'm wondering if the repositories (or whatever the yum equivalent is) are pointing to good places. Thank you

2 2

Has anyone gotten KDiff3 to work on CentOS 4.X?
by Alfred von Campe 25 Jun '07

25 Jun '07

The Subject: line says it all. I haven't been able to find a KDiff3 RPM (http://kdiff3.sourceforge.net) that will install on CentOS 4, and I am also having problems building it from source (the application that is, not the RPM). I have some users who really want to use KDiff3, so any help/hints are appreciated. Thanks, Alfred

1 0

iptables rule (MAC filtering)
by Jordi Espasa Clofent 25 Jun '07

25 Jun '07

Hi all, I've a CentOS box which as two NIC; this box is also a router for LAN subnet: ------------------------------------ | eth0 (external) 172.0.0.1 | | eth1 (internal) 192.168.1.1 | ------------------------------------ | LAN clients (192.168.1.2+) I want to allow http acces only for two LAN boxes; an only http access, which means that others protocols as smtp, pop3, imap and so on will be permited. The rest of LAN boxes will be redirected to a local http service (192.168.1.1:80) I think the best way is creating a iptables rules based on MAC address. So, the rules I've made are: iptables -t nat -A PREROUTING -p tcp -s 192.168.1.0/24 -m mac --mac-source ! xx:xx:xx:xx:xx:xx --dport 80 -j DNAT --to-destination 192.168.1.1:80 iptables -t nat -A PREROUTING -p tcp -s 192.168.1.0/24 -m mac --mac-source ! xx:xx:xx:xx:xx:xx --dport 80 -j DNAT --to-destination 192.168.1.1:80 Please, note the exclamation symbol, which means a logical negation. But it seems doesn't work correctly: all the LAN clients can suffer the web. ¿?¿?¿

2 4

xen and atl1
by Kamill S 25 Jun '07

25 Jun '07

Hello list, did someone have a similar issue like I have? -> Bought an AMD X2 3600+ and an Asus M2V (with Attansic L1 Gigabit Ethernet Adapter). Installed Centos 5 64_x86 and build atl1 from this source -> http://www.hogchain.net/attansic/AtL1Linux_v1.0.41.0.tar.gz After an insmod atl1 Centos say good bye with a kernel panic. I could only remind that there stand "Bad RIP value." and "_stext...." The driver runs fine with a non-xen kernel. Sorry for my scanty description. Its only a general question. Do someone have some informations? With google I don't have success. My next step is mailing to xen mailinglist. Thanks!

1 0

Re: [CentOS] How to build clamav SRPM and RPM with calmav tarbal - CentOS 5
by Kenneth Porter 25 Jun '07

25 Jun '07

On Monday, June 25, 2007 7:14 AM -0700 Akemi Yagi <amyagi(a)gmail.com> wrote: > Then, Rodrigo's note may help: > > http://lists.rpmforge.net/pipermail/users/2007-June/000798.html The earlier discussion on CentOS list: <http://lists.centos.org/pipermail/centos/2007-June/082857.html>

1 0

Re: [CentOS] How to build clamav SRPM and RPM with calmav tarbal - CentOS 5
by Akemi Yagi 25 Jun '07

25 Jun '07

The message below was not posted to the ML, so I am sending it here. On 6/24/07, Akemi Yagi <amyagi(a)gmail.com> wrote: > On 6/24/07, Indunil Jayasooriya <indunil75(a)gmail.com> wrote: > > > > > > How to build both clamav SRPM AND RPM for CentOS 5 > > > > > > You don't have to. clamav is available from RPMforge. > > > > I installed it fro Dag. But it gace erros. Then I desabled selinux. Then , > > It worked. But i do not want to leave selinux disabled. > > > > That's why. I am trying to build it. Then, Rodrigo's note may help: http://lists.rpmforge.net/pipermail/users/2007-June/000798.html Akemi

2 1

USB keypad
by Jerry Geis 25 Jun '07

25 Jun '07

I have a USB keypad that I am trying to use with Centos 5. dmesg reports. input: ORTEK USB Keyboard Hub as /class/input/input8 input: USB HID v1.10 Keyboard [ORTEK USB Keyboard Hub] on usb-0000:00:02.0-4.3 input: ORTEK USB Keyboard Hub as /class/input/input9 input: USB HID v1.10 Device [ORTEK USB Keyboard Hub] on usb-0000:00:02.0-4.3 lsusb shows: Bus 001 Device 010: ID 05a4:9862 Ortek Technology, Inc. Bus 001 Device 009: ID 05a4:9837 Ortek Technology, Inc. This doesnt seem to work on centos 5. However it does work on centos 4.5 input: ORTEK USB Keyboard Hub as /class/input/input4 input: USB HID v1.10 Keyboard [ORTEK USB Keyboard Hub] on usb-0000:00:0b.0-4.3 input: ORTEK USB Keyboard Hub as /class/input/input5 input: USB HID v1.10 Device [ORTEK USB Keyboard Hub] on usb-0000:00:0b.0-4.3 lsusb shows: Bus 002 Device 004: ID 05a4:9862 Ortek Technology, Inc. Bus 002 Device 003: ID 05a4:9837 Ortek Technology, Inc. How can I get this working on centos 5??? Thanks, Jerry

1 0

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss