Out of order meaning, it puts the additional ethernet card as eth0, with the built-in ports as eth1 and eth2 respectively. WITHOUT the additional card installed, it puts the built-in ports as eth0 and eth1, which is what I want it to do. The additional card should be eth2, at least that's what I want it to do.
Looking at persistent-net.rules, it always puts the additional card first, both without your script as well as with. I need it to be last. The system's built-ins should always be eth0 and eth1 respectively.
And dmesg confirms it as well, it identifies the added card first (and assigns it eth0), then identifies the built-in ports. I'd grab the actual output except I need to manually reconfigure the interfaces so I can actually get ON the machine. Right now I'm just looking at its console.
On Wed, Feb 25, 2015 at 3:37 PM, Jason Warr jason@warr.net wrote:
Define out of order in this case just so I know for sure what you mean.
What my solution does, or at least does reliably in my case, is make sure the interfaces are in the same order once installed as the install kernel saw them. It won't re-order them to be sequential based on bus, mac or driver. I am working on that but it will also include naming the devices based on the module name, similar to how FreeBSD and Solaris do it.
Just to get an idea of what might be going on can you run "dmesg | grep eth" so I can see some of what udev is doing?
On Wed, 25 Feb 2015 16:28:31 -0600, Ashley M. Kirchner ashley@pcraft.com wrote:
Ok, when I run that, it creates a now "custom" 70-persistent-net.rules,
but the interfaces are still out of order, with the added one listed first, and the built-ins 2nd and 3rd.
On Wed, Feb 25, 2015 at 2:00 PM, Jason Warr jason@warr.net wrote:
Here is my script for post install if you want to try it.
In order for the shuffling to not occur you do need to create the udev rules file somehow. I am not sure how mangled this will be in email but it is worth a try. It should run OK with nothing else. I have a better version in the works but the enhancements are mainly useful for Fedora 19-21.
I did forget to say I also block NetworkManager from the interfaces.
############################
#!/bin/bash ## BIND MAC address to proper interfaces so they stay persistent ## I want them to stay as they were in kickstart
## This can cause issues with VLAN interfaces for both bond dev's and base eth dev's. ## The bond one was solved by adding in the "KERNEL="eth?*" as that will only apply to physical ## Devices. Once we have VLAN's on a real device instead of just on BOND's this then applies ## to the hardware devices as well. The core issue is that the MAC address is inherited ## by all of the children devices and thus the UDEV rule has to be crafted to only apply ## to the base physical device. ## This one was solved via adding DRIVERS=="?*" as the VLAN int's wont have one
echo "[KICKSTART] Binding eth interfaces to the expected MAC addressin UDEV" echo "## Created by Kickstart to keep network interfaces in an expected order" > \ /etc/udev/rules.d/70-persistent-net.rules echo "" >> \ /etc/udev/rules.d/70-persistent-net.rules
cd /sys/class/net/ for NETDEV in $(ls | grep eth | sort) do ## Create a UDEV rule for each eth interface echo "## ${NETDEV} interface" >> \ /etc/udev/rules.d/70-persistent-net.rules ## We throw this one in here as it can contain some usefulinformation echo "## $(dmesg | grep ${NETDEV} | grep -i -v -e "console" -e "Command line" | head -1)" >> \ /etc/udev/rules.d/70-persistent-net.rules
echo -n "SUBSYSTEM==\"net\", ACTION==\"add\", DRIVERS==\"?*\", "\
/etc/udev/rules.d/70-persistent-net.rulesecho -n "ATTR{address}==\"$(cat ${NETDEV}/address)\", " >> \ /etc/udev/rules.d/70-persistent-net.rules echo -n "ATTR{dev_id}==\"0x0\", ATTR{type}==\"1\",KERNEL=="eth?*", " >> \ /etc/udev/rules.d/70-persistent-net.rules echo -e "NAME="${NETDEV}"\n" >> \ /etc/udev/rules.d/70-persistent-net.rules
## Make a log of the devices present during install echo -e "${NETDEV} $(cat ${NETDEV}/address)\n" >>/root/ksnet-devices
## Also remove the HWADDR line from all of the net config files grep -v -e NAME -e HWADDR -e NM_CONTROLLED \ /etc/sysconfig/network-scripts/ifcfg-${NETDEV} | sed's/"//g' \ > /etc/sysconfig/network-scripts/ifcfg-${NETDEV}-tmp echo "NM_CONTROLLED=no" >> /etc/sysconfig/network- scripts/ifcfg-${NETDEV}-tmp /usr/bin/perl -p -i -e 's/dhcp/none/' /etc/sysconfig/network- scripts/ifcfg-${NETDEV}-tmp mv -f /etc/sysconfig/network-scripts/ifcfg-${NETDEV}-tmp \ /etc/sysconfig/network-scripts/ifcfg-${NETDEV} done
###########################
On Wed, 25 Feb 2015 14:53:40 -0600, Ashley M. Kirchner < ashley@pcraft.com> wrote:
Thanks for that Jason but it didn't solve the problem. The system is still
coming up with the interfaces shuffled. It seems to *always* want to use the added ethernet card as eth0.
On Wed, Feb 25, 2015 at 1:37 PM, Jason Warr jason@warr.net wrote:
Starting back in RHEL/Cent 5 I found that the only way to make sure your
interface enumeration was consistent after install with what you had during install was to create a udev rules file using the mac addresses as the key. It is easy to run a short script in postinstall to create it based on how anaconda has seen them.
In order for this to work on Cent 6 you have to set biosdevname=0 on the kernel boot for the installed system.
PXE boot options:
label c6inst-sda kernel /linux-boot/cent6-x64/vmlinuz append initrd=/linux-boot/cent6-x64/initrd.img ksdevice=bootif ip=dhcp ks=http://xx.xx.xx.xx/install/linux/ks/basic-cent6-sda.cfg ipappend 2
In kickstart:
BOOTOPTS="biosdevname=0"
Also in kickstart I do not specify the config for ANY network interfaces. I let anaconda pull in only the config for the boot interface from PXE. I manually configure everything else. The only thing I do to non-boot interfaces is set the DHCP and ONBOOT to no.
On Wed, 25 Feb 2015 14:21:18 -0600, Ashley M. Kirchner < ashley@pcraft.com> wrote:
Version 6.6 ...
On Wed, Feb 25, 2015 at 1:17 PM, Jim Perrin jperrin@centos.org wrote:
<overly trimmed>
> On 02/25/2015 01:56 PM, Ashley M. Kirchner wrote: > > Ok, so some of this now works, but I'm still having problems. With > the > > bootif option, the system now correctly configures and uses the > same > > interface to get its kickstart file. However, when the system is > done > and > > boots up, the interfaces are still messed up. So this is what I > have > in > the > > kickstart file: > > What version of CentOS 6 is this? > > > In the PXE config file I have: > > > > IPAPPEND 2 > > APPEND ks=http://192.168.x.x/ks/portico.ks > initrd=centos/x86_64/initrd.img > > ramdisk_size=100000 ksdevice=bootif > > > As soon as I *remove* the additional ethernet card, the system will > boot > up > > with the ports configured correctly (port 1 = eth0, port 2 = eth1). > So > why > > is it that as soon as there is an additional one, all things go to > hell? > > Why must the boot process shuffle them? More importantly, how do I > prevent > > this so that the system comes up properly after a kickstart > install? > > > > The reason I ask the version, is this is exactly the sort of thing > that > biosdevname is designed to solve. With biosdevname, you get devices > like > 'em1, em2, p6p1', which aren't as friendly as 'eth0' but also keep > names > sane and avoid the hair-tearing issues you're experiencing currently. > You don't appear to be adding anything via your append line that > would > disable biosdevname, so I must assume you're using a much older 6 > base > install. > > > In my experience biosdevname creates just as many problems as it > solves.
Dell can keep it.
--
Jim Perrin > The CentOS Project | http://www.centos.org > twitter: @BitIntegrity | GPG Key: FA09AD77 > _______________________________________________ > CentOS mailing list > CentOS@centos.org > http://lists.centos.org/mailman/listinfo/centos > > > _______________________________________________ > > CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos
CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos
CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos
CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos