Sorin Srbu wrote:
From: centos-bounces@centos.org [mailto:centos-bounces@centos.org] On Behalf Of Toshaan Bharvani
Sent: Tuesday, August 19, 2008 4:24 PM
To: centos@centos.org
Subject: Re: [CentOS] wireless laptop configuration
Sorin Srbu wrote:
From: centos-bounces@centos.org [mailto:centos-bounces@centos.org] On Behalf Of Toshaan Bharvani
Sent: Tuesday, August 19, 2008 2:42 PM
To: centos@centos.org
Subject: Re: [CentOS] wireless laptop configuration
Steve Huff wrote:
On Aug 19, 2008, at 5:04 AM, Sorin@Gmail wrote:
I'm using a 3Com 3CRWE154G72 IIRC, which according to the
hwconf's using the
prism54 driver/firmware/whatever.
Would I maybe be better off reinstalling the whole shebang and
have the
wifi-card inserted from start in order for the centos
installer to
see it
properly from the beginning?
before you do that, open a terminal, become root, and run
/usr/sbin/kudzu (while the wireless card is installed). that's the
program that does hardware detection; it may be able to sort out
your
issue.
-steve
or if kudzu for some reason doesn't cooperate (which is always on my system)
become root
run : /sbin/modprobe prism54
run : dmesg | tail
and read whether it just says it has loaded the module (single line) or
detected will output a wlanX statement and you are in business
Isn’t it implied that since ”prism54” is listed in /etc/sysconfig/hwconf for the wifi-card that the module has been loaded already? Or is this some of the magical stuff that sometimes doesn’t happen for whatever reason? 8-)
/etc/sysconfig/hwconf is the file kudzu creates when of all detected hardware at startup and it related this hardware with drivers in the kernel
but certain drivers are modules in the kernel, wich need to be loaded manually or later when the system is already running
this can be done by method 1 explained here above or adding them in /etc/modprobe.conf which makes it load the modules at startup
you will need to add the line (if it is not yet there) :
alias wlan0 prism54
you can check whether the module is loaded with : /sbin/lsmod | grep prism54 This is how far I got with the above hints. For some reason I don’t have a wlan0, but instead a eth0. I did create an alias in Network Manager for eth0 > wlan0. Then I ran the below modprobe command according to the below. “[root@centos-v5-x86 ~]# /sbin/modprobe prism54 [root@centos-v5-x86 ~]# dmesg|tail eth0: resetting device... eth0: uploading firmware... prism54: request_firmware() failed for 'isl3890' eth0: could not upload firmware ('isl3890') eth0: islpci_reset: failure eth0: resetting device... eth0: uploading firmware... prism54: request_firmware() failed for 'isl3890' eth0: could not upload firmware ('isl3890') eth0: islpci_reset: failure [root@centos-v5-x86 ~]#”
“When I try to activate wlan0, I get this message: Error for wireless request "Set Bit Rate" (8B20) : SET failed on device eth0 ; Input/output error. Determining IP information for eth0...SIOCSIFFLAGS: No such file or directory SIOCSIFFLAGS: No such file or directory failed.” In /etc/modprobe.conf I’ve added the line “alias wlan0 prism54”. What’s more, I went to the prism54.org site and found a firmware, downloaded it and as per instructed on the site, renamed the .arm-file to isl3890 and put it in /usr/lib/hotplug/firmware. Upon restarting and activating wlan0 I still get the above SIOC-error. I have a hunch this might actually work if I put the isl3890-file in the correct place. Not sure /usr/lib/hotplug/firmware *is* actually right, as I had to create the hotplugs and firmware-folders. Any hints on this guys? TIA.
_______________________________________________ CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos
you have used the following :
2.5.2.0.arm : http://daemonizer.de/prism54/prism54-fw/fw-softmac/2.5.2.0.arm
Version 2.5.2.0 built on Thu Mar 4 16:05:03 CET 2004 by inlbuild@tix
87a5519d70c16991b8fff9b3b31de68e
headers
Source: 3CRWE154G72_Jul_08_04.exe try renaming to isl3886 as it is a pcmcia card so it is equal to a pci version and then put in in /lib/firmware
_________________________________________________________________ Invite your mail contacts to join your friends list with Windows Live Spaces. It's easy! http://spaces.live.com/spacesapi.aspx?wx_action=create&wx_url=/friends.a...