Hi all
I'm trying to setup second ethernet on Dell 2950 server but there isn't any eth1 device (in the bios are ON)
# dmesg |grep eth eth0: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f8000000, IRQ 169, node addr 001c23d878bb eth1: Broadcom NetXtreme II BCM5708 1000Base-T (B2) PCI-X 64-bit 133MHz found at mem f4000000, IRQ 169, node addr 001c23d878bd bnx2: eth0: using MSI bnx2: eth0 NIC Link is Up, 100 Mbps full duplex
# uname -a Linux vmta2.contactlab.it 2.6.18-53.1.6.el5 #1 SMP Wed Jan 23 11:28:47 EST 2008 x86_64 x86_64 x86_64 GNU/Linux
# ifconfig -a dev707 Link encap:Ethernet HWaddr 00:1C:23:D8:78:BD BROADCAST MULTICAST MTU:1500 Metric:1 RX packets:0 errors:0 dropped:0 overruns:0 frame:0 TX packets:0 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:0 (0.0 b) TX bytes:0 (0.0 b) Interrupt:169 Memory:f4000000-f4012100
eth0 Link encap:Ethernet HWaddr 00:1C:23:D8:78:BB inet addr:xxxxxxxxxx Bcast:xxxxxxxxx Mask:255.255.255.0 inet6 addr: fe80::21c:23ff:fed8:78bb/64 Scope:Link UP BROADCAST RUNNING MULTICAST MTU:1500 Metric:1 RX packets:119649 errors:0 dropped:0 overruns:0 frame:0 TX packets:43871 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:1000 RX bytes:91428814 (87.1 MiB) TX bytes:5879945 (5.6 MiB) Interrupt:169 Memory:f8000000-f8012100
lo Link encap:Local Loopback inet addr:127.0.0.1 Mask:255.0.0.0 inet6 addr: ::1/128 Scope:Host UP LOOPBACK RUNNING MTU:16436 Metric:1 RX packets:14 errors:0 dropped:0 overruns:0 frame:0 TX packets:14 errors:0 dropped:0 overruns:0 carrier:0 collisions:0 txqueuelen:0 RX bytes:848 (848.0 b) TX bytes:848 (848.0 b)
# ls -la /sys/class/net/ total 0 drwxr-xr-x 6 root root 0 Jan 24 10:39 . drwxr-xr-x 30 root root 0 Jan 24 10:39 .. drwxr-xr-x 3 root root 0 Jan 24 10:57 dev707 drwxr-xr-x 3 root root 0 Jan 24 10:40 eth0 drwxr-xr-x 3 root root 0 Jan 24 10:40 lo drwxr-xr-x 3 root root 0 Jan 24 10:40 sit0
# lsmod |grep bnx bnx2 190425 0
# cat /etc/modprobe.conf alias eth0 bnx2 alias eth1 bnx2 alias scsi_hostadapter megaraid_sas alias scsi_hostadapter1 ata_piix
How can I do to setup eth1 device?
kind regards