Dear All,
<br />
<br />I have managed perfectly fine to install centos 5.5 x64 on a new sun blade x6270 server module .i had to install in text mode since GUI install mode was not working
<br />
<br />Actually this machine is going to replace my current working very low hardware server
<br />the server is used as my primary dns, mail server , webmail server also running Mailscanner, mailwatch etc.
<br />Also I want to use this new sun blade server as a virtual machine using xen
<br />
<br />i have installed xen and uts fine
<br />
<br />but i have a issue with the diplay driver 
<br />
<br />I did run system-config-network and selected the card as ast-ASpeedTech chipsets since my lspci says i have a 
<br />20:05.0 VGA compatible controller: ASPEED Technology, Inc. ASPEED Graphics Family (rev 10)
<br />
<br />now I run startx and i get  the below error
<br />X Window System Version 7.1.1
<br />Release Date: 12 May 2006
<br />X Protocol Version 11, Revision 0, Release 7.1.1
<br />Build Operating System: Linux 2.6.18-53.el5 x86_64 Red Hat, Inc.
<br />Current Operating System: Linux kmundns 2.6.18-194.26.1.el5xen #1 SMP Tue Nov 9 13:35:30 EST 2010 x86_64
<br />Build Date: 17 November 2010
<br />Build ID: xorg-x11-server 1.1.1-48.76.el5_5.2 
<br />        Before reporting problems, check http://wiki.x.org
<br />        to make sure that you have the latest version.
<br />Module Loader present
<br />Markers: (--) probed, (**) from config file, (==) default setting,
<br />        (++) from command line, (!!) notice, (II) informational,
<br />        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
<br />(==) Log file: &quot;/var/log/Xorg.0.log&quot;, Time: Thu Dec 16 21:17:19 2010
<br />(==) Using config file: &quot;/etc/X11/xorg.conf&quot;
<br />dlopen: /usr/lib64/xorg/modules/drivers/ast_drv.so: wrong ELF class: ELFCLASS32
<br />(EE) Failed to load /usr/lib64/xorg/modules/drivers/ast_drv.so
<br />(EE) Failed to load module &quot;ast&quot; (loader failed, 7)
<br />(EE) No drivers available.
<br />
<br />Fatal server error:
<br />no screens found
<br />XIO:  fatal IO error 104 (Connection reset by peer) on X server &quot;:0.0&quot;
<br />      after 0 requests (0 known processed) with 0 events remaining.
<br />---------------------------------------------------------
<br />
<br />then i did change the driver to vesa and running startx shows me as below
<br />
<br />xauth:  creating new authority file /root/.serverauth.16448
<br />
<br />
<br />X Window System Version 7.1.1
<br />Release Date: 12 May 2006
<br />X Protocol Version 11, Revision 0, Release 7.1.1
<br />Build Operating System: Linux 2.6.18-53.el5 x86_64 Red Hat, Inc.
<br />Current Operating System: Linux kmundns 2.6.18-194.26.1.el5xen #1 SMP Tue Nov 9 13:35:30 EST 2010 x86_64
<br />Build Date: 17 November 2010
<br />Build ID: xorg-x11-server 1.1.1-48.76.el5_5.2 
<br />        Before reporting problems, check http://wiki.x.org
<br />        to make sure that you have the latest version.
<br />Module Loader present
<br />Markers: (--) probed, (**) from config file, (==) default setting,
<br />        (++) from command line, (!!) notice, (II) informational,
<br />        (WW) warning, (EE) error, (NI) not implemented, (??) unknown.
<br />(==) Log file: &quot;/var/log/Xorg.0.log&quot;, Time: Thu Dec 16 21:10:35 2010
<br />(==) Using config file: &quot;/etc/X11/xorg.conf&quot;
<br />(EE) VESA(0): No valid modes
<br />(EE) Screen(s) found, but none have a usable configuration.
<br />
<br />Fatal server error:
<br />no screens found
<br />XIO:  fatal IO error 104 (Connection reset by peer) on X server &quot;:0.0&quot;
<br />      after 0 requests (0 known processed) with 0 events remaining.
<br />------------------------------------------------------------
<br />
<br />i really apprecite if someone out there would help me and advise
<br />
<br />
<br />Thanks and Regards
<br />
<br />simon
<br />
<br />I really need the graphic to setup virtual machine since in GUI is quite simple