On Thu, 27 Oct 2016 11:25, Alessandro Baggi wrote:
Il 24/10/2016 14:05, Leonard den Ottolander ha scritto:
On Mon, 2016-10-24 at 12:07 +0200, Alessandro Baggi wrote:
=== START OF READ SMART DATA SECTION === SMART Error Log not supported
I reckon there's a <snip> between those lines. The line right after the first should read something like:
SMART overall-health self-assessment test result: PASSED
or "FAILED" for that matter. If not try running
smartctl -t short /dev/sda
, wait for the indicated time to expire, then check the output of smartctl -a (or -x) again.
Regards, Leonard.
Hi Leonard, after a smart short test, the output of smartctl -a /dev/... is
=== START OF INFORMATION SECTION === Model Family: SandForce Driven SSDs Device Model: Corsair Force GT Serial Number: 12297948000015020A81 LU WWN Device Id: 0 000000 000000000 Firmware Version: 5.02 User Capacity: 120,034,123,776 bytes [120 GB] Sector Size: 512 bytes logical/physical Rotation Rate: Solid State Device Device is: In smartctl database [for details use: -P show] ATA Version is: ATA8-ACS, ACS-2 T13/2015-D revision 3 SATA Version is: SATA 3.0, 6.0 Gb/s (current: 6.0 Gb/s) Local Time is: Thu Oct 27 11:22:22 2016 CEST SMART support is: Available - device has SMART capability. SMART support is: Enabled
=== START OF READ SMART DATA SECTION === SMART overall-health self-assessment test result: PASSED
General SMART Values: Offline data collection status: (0x02) Offline data collection activity was completed without error. Auto Offline Data Collection: Disabled. Self-test execution status: ( 0) The previous self-test routine completed without error or no self-test has ever been run. Total time to complete Offline data collection: ( 0) seconds. Offline data collection capabilities: (0x7b) SMART execute Offline immediate. Auto Offline data collection on/off support. Suspend Offline collection upon new command. Offline surface scan supported. Self-test supported. Conveyance Self-test supported. Selective Self-test supported. SMART capabilities: (0x0003) Saves SMART data before entering power-saving mode. Supports SMART auto save timer. Error logging capability: (0x01) Error logging supported. General Purpose Logging supported. Short self-test routine recommended polling time: ( 1) minutes. Extended self-test routine recommended polling time: ( 48) minutes. Conveyance self-test routine recommended polling time: ( 2) minutes. SCT capabilities: (0x0021) SCT Status supported. SCT Data Table supported.
SMART Attributes Data Structure revision number: 10 Vendor Specific SMART Attributes with Thresholds: ID# ATTRIBUTE_NAME FLAG VALUE WORST THRESH TYPE UPDATED WHEN_FAILED RAW_VALUE 1 Raw_Read_Error_Rate 0x000f 120 120 050 Pre-fail Always - 0/0 5 Retired_Block_Count 0x0033 100 100 003 Pre-fail Always - 0 9 Power_On_Hours_and_Msec 0x0032 000 000 000 Old_age Always - 17394h+07m+56.840s 12 Power_Cycle_Count 0x0032 099 099 000 Old_age Always - 1974 171 Program_Fail_Count 0x0032 000 000 000 Old_age Always - 0 172 Erase_Fail_Count 0x0032 000 000 000 Old_age Always - 0 174 Unexpect_Power_Loss_Ct 0x0030 000 000 000 Old_age Offline - 780 177 Wear_Range_Delta 0x0000 000 000 000 Old_age Offline - 3 181 Program_Fail_Count 0x0032 000 000 000 Old_age Always - 0 182 Erase_Fail_Count 0x0032 000 000 000 Old_age Always - 0 187 Reported_Uncorrect 0x0032 100 100 000 Old_age Always - 0 194 Temperature_Celsius 0x0022 029 042 000 Old_age Always - 29 (Min/Max 15/42) 195 ECC_Uncorr_Error_Count 0x001c 100 100 000 Old_age Offline - 0/0 196 Reallocated_Event_Ct 0x0033 100 100 003 Pre-fail Always - 0 201 Unc_Soft_Read_Err_Rate 0x001c 100 100 000 Old_age Offline - 0/0 204 Soft_ECC_Correct_Rate 0x001c 100 100 000 Old_age Offline - 0/0 230 Life_Curve_Status 0x0013 100 100 000 Pre-fail Always - 100 231 SSD_Life_Left 0x0013 100 100 010 Pre-fail Always - 0 233 SandForce_Internal 0x0000 000 000 000 Old_age Offline - 6599 234 SandForce_Internal 0x0032 000 000 000 Old_age Always - 6894 241 Lifetime_Writes_GiB 0x0032 000 000 000 Old_age Always - 6894 242 Lifetime_Reads_GiB 0x0032 000 000 000 Old_age Always - 6326
SMART Error Log not supported
SMART Self-test Log not supported
SMART Selective self-test log data structure revision number 1 SPAN MIN_LBA MAX_LBA CURRENT_TEST_STATUS 1 0 0 Not_testing 2 0 0 Not_testing 3 0 0 Not_testing 4 0 0 Not_testing 5 0 0 Not_testing Selective self-test flags (0x0): After scanning selected spans, do NOT read-scan remainder of disk. If Selective self-test is pending on power-up, resume after 0 minute delay.
Hmm, lets do some math: 17394 hours "on"-time equals 724.7 days (at continous "on"). 6894 GiB written at 120 GiB drive sizes gives 57.4 Drive-Writes (at optimal wearleveling every cell would have been written 57-58 times)
The used Sandforce controller (likly a SF-2281) is not the best at wearleveling, so the "use"-count per cell will be most likely more than double that.
For my personal use I would replace that Drive asap. - There is no warranty for it anymore (time since buy) - You can't buy it new anymore (discontinued) - There are more reliable drives available.
I'd go for a Samsung Evo 850, that will give you five years of warranty.
But, it's your drive, you make the decissions.
- Yamaban.