Hello All,
I'm installing some DIY routers, composed of Intel nuc's ,Linksys usb-ethernet adapters and Centos7
On most machines I just plug in the usb device, install Centos7 and everything works. But on this one machine the network interface doesn't work.
After installing ip addr shows:
[root@clgmol ~]# ip addr 1: lo: <LOOPBACK,UP,LOWER_UP> mtu 65536 qdisc noqueue state UNKNOWN qlen 1 link/loopback 00:00:00:00:00:00 brd 00:00:00:00:00:00 inet 127.0.0.1/8 scope host lo valid_lft forever preferred_lft forever inet6 ::1/128 scope host valid_lft forever preferred_lft forever 2: enp3s0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc pfifo_fast state UP qlen 1000 link/ether f4:4d:30:64:21:bb brd ff:ff:ff:ff:ff:ff inet 192.168.80.189/25 brd 192.168.80.255 scope global dynamic enp3s0 valid_lft 431sec preferred_lft 431sec inet6 fe80::f64d:30ff:fe64:21bb/64 scope link valid_lft forever preferred_lft forever 3: wlp2s0: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether b8:81:98:9f:8f:1c brd ff:ff:ff:ff:ff:ff 4: enp0s20u3c2: <BROADCAST,MULTICAST> mtu 1500 qdisc noop state DOWN qlen 1000 link/ether 14:91:82:3b:7b:b9 brd ff:ff:ff:ff:ff:ff
[root@clgmol ~]# dmesg | tail -n15 [ 10.582462] Bluetooth: hci0: Intel device is already patched. patch num: 25 [ 10.770781] usb 2-3: new SuperSpeed USB device number 3 using xhci_hcd [ 10.782704] usb 2-3: New USB device found, idVendor=13b1, idProduct=0041 [ 10.782728] usb 2-3: New USB device strings: Mfr=1, Product=2, SerialNumber=6 [ 10.782745] usb 2-3: Product: Linksys USB3GIGV1 [ 10.782759] usb 2-3: Manufacturer: Linksys [ 10.782772] usb 2-3: SerialNumber: 000001000000 [ 10.787858] cdc_ether 2-3:2.0 eth0: register 'cdc_ether' at usb-0000:00:14.0-3, CDC Ethernet Device, 14:91:82:3b:7b:b9 [ 14.140292] nf_conntrack version 0.5.0 (16384 buckets, 65536 max) [ 14.175958] Netfilter messages via NETLINK v0.30. [ 14.178428] ctnetlink v0.93: registering with nfnetlink. [ 14.350689] ipt_ULOG: ULOG: fail to register logger. [ 15.192593] ipt_ULOG: ULOG: fail to register logger.
I create /etc/sysconfig/network-scripts/ifcfg-enp0s20u3c2 using the hardware address from ip addr en uuid created with uuidgen but I don't understand why it's not created on install:
TYPE=Ethernet BOOTPROTO=static DEFROUTE=yes IPV4_FAILURE_FATAL=no IPV6INIT=no IPV6_AUTOCONF=yes IPV6_DEFROUTE=yes IPV6_PEERDNS=yes IPV6_PEERROUTES=yes IPV6_FAILURE_FATAL=no IPV6_ADDR_GEN_MODE=stable-privacy NAME=enp0s20u3c2 UUID=a728528c-0be7-49bc-9478-05743a285a7d DEVICE=enp0s20u3c2 ONBOOT=yes PEERDNS=yes PEERROUTES=yes NM_CONTROLLED=no HWADDR=14:91:82:3b:7b:b9 IPADDR=192.168.70.1 NETMASK=255.255.255.0
Next I cannot launch the network:
[root@clgmol ~]# systemctl status network ● network.service - LSB: Bring up/down networking Loaded: loaded (/etc/rc.d/init.d/network; bad; vendor preset: disabled) Active: failed (Result: exit-code) since di 2017-02-21 20:57:56 CET; 15s ago Docs: man:systemd-sysv-generator(8) Process: 2638 ExecStart=/etc/rc.d/init.d/network start (code=exited, status=1/FAILURE) CGroup: /system.slice/network.service └─1076 /sbin/dhclient -H clgmol -1 -q -lf /var/lib/dhclient/dhclient-13b56b89-7b1d-42fa-aeb7-af96a38102ce-enp3s0.lease -pf /var/run/dhclient-enp3s0.pid en...
feb 21 20:57:56 clgmol.router network[2638]: RTNETLINK answers: File exists feb 21 20:57:56 clgmol.router network[2638]: RTNETLINK answers: File exists feb 21 20:57:56 clgmol.router network[2638]: RTNETLINK answers: File exists feb 21 20:57:56 clgmol.router network[2638]: RTNETLINK answers: File exists feb 21 20:57:56 clgmol.router network[2638]: RTNETLINK answers: File exists feb 21 20:57:56 clgmol.router network[2638]: RTNETLINK answers: File exists feb 21 20:57:56 clgmol.router systemd[1]: network.service: control process exited, code=exited status=1 feb 21 20:57:56 clgmol.router systemd[1]: Failed to start LSB: Bring up/down networking. feb 21 20:57:56 clgmol.router systemd[1]: Unit network.service entered failed state. feb 21 20:57:56 clgmol.router systemd[1]: network.service failed.
[root@clgmol ~]# ifup enp0s20u3c2 arping: recvfrom: Netwerk ligt plat RTNETLINK answers: Network is down
I disabled NetworkManager I tried with another Linksys device and I reinstalled and started over.
Why does it work with other devices and not with this one? Many thanks for any advise.
Greetings, J