At 05:14 PM 1/23/2006, Craig White wrote:
On Mon, 2006-01-23 at 16:57 -0500, Robert Moskowitz wrote:
I am running Asterisk@home on one of my systems here. It uses Centos 4.2. It does NOT have a GUI interface. Command line only at console or via SSH (yeah, I know that I was working on another server to get GUI tools working through SSH, but I am NOT going to muck with AAH build).
Now at http://www.voip-info.org/wiki/view/Asterisk%40Home+Handbook+Wiki+Chapter+3
I was instructed to use NETCONFIG to setup up my network information. Well it did for eth0, but not for eth1.
So question #1 is how to use netconfig to setup eth1 without
messing with eth0.
don't know - never used it.
try...
cd /etc/sysconfig/network-scripts cp ifcfg-eth0 ifcfg-eth1
and then edit ifcfg-eth1 to your liking
Well I started in on this and look at the two files before any changes:
cat ifcfg-eth0
DEVICE=eth0 ONBOOT=yes BOOTPROTO=static IPADDR=65.84.78.218 NETMASK=255.255.255.248 GATEWAY=65.84.78.217
cat ifcfg-eth1
DEVICE=eth1 HWADDR=00:50:8B:DA:BB:61 ONBOOT=no TYPE=Ethernet
Why does eth1 have HWADDR and TYPE whereas eth0 does not?
Seems I should understand this before making changes!
#2) NETCONFIG did not setup my hostname and domain. I had to go in with VI to resolv.conf and sysconfig/network. Is there a tool for this?
simply edit /etc/sysconfig/network
change the hostname to anything you want it to be - suggest that you make sure this entry also exists in /etc/hosts
Also when using 2 eth devices per above, set the gateway address here...
GATEWAYDEV=eth0 # fix for your situation GATEWAY=ip_addr_of_gateway
#3) How do I figure out which board is which. Other than looking at the MAC address and using PCISNIFFER to then relate that to one of the boards (well, one 'builtin'). Also how do I determine which board is using which IRQ.
dmesg|less
or
lspci -vv
Here is the output of that lapci command. You will see that the first ethernet and last Tiger Jet are both on IRQ5.
Is this controlled/controllable via some config file?
02:04.0 Ethernet controller: Intel Corporation 82557/8/9 [Ethernet Pro 100] (rev 01) Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap- 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min, 14000ns max) Interrupt: pin A routed to IRQ 5 Region 0: Memory at 40700000 (32-bit, prefetchable) [size=4K] Region 1: I/O ports at 1840 [size=32] Region 2: Memory at 40000000 (32-bit, non-prefetchable) [size=1M]
02:08.0 Ethernet controller: Intel Corporation 82801BA/BAM/CA/CAM Ethernet Controller (rev 01) Subsystem: Compaq Computer Corporation EtherExpress PRO/100 VM Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B+ ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (2000ns min, 14000ns max), Cache Line Size 08 Interrupt: pin A routed to IRQ 10 Region 0: Memory at 40100000 (32-bit, non-prefetchable) [size=4K] Region 1: I/O ports at 1800 [size=64] Capabilities: [dc] Power Management version 2 Flags: PMEClk- DSI+ D1+ D2+ AuxCurrent=0mA PME(D0+,D1+,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=2 PME-
02:09.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Intel Corporation: Unknown device 0003 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (250ns min, 32000ns max) Interrupt: pin A routed to IRQ 11 Region 0: I/O ports at 1000 [size=256] Region 1: Memory at 40200000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-
02:0a.0 Communication controller: Tiger Jet Network Inc. Tiger3XX Modem/ISDN interface Subsystem: Intel Corporation: Unknown device 0003 Control: I/O+ Mem+ BusMaster+ SpecCycle- MemWINV- VGASnoop- ParErr- Stepping- SERR+ FastB2B- Status: Cap+ 66Mhz- UDF- FastB2B- ParErr- DEVSEL=medium >TAbort- <TAbort- <MAbort- >SERR- <PERR- Latency: 66 (250ns min, 32000ns max) Interrupt: pin A routed to IRQ 5 Region 0: I/O ports at 1400 [size=256] Region 1: Memory at 40300000 (32-bit, non-prefetchable) [size=4K] Capabilities: [40] Power Management version 2 Flags: PMEClk- DSI+ D1- D2+ AuxCurrent=55mA PME(D0+,D1-,D2+,D3hot+,D3cold+) Status: D0 PME-Enable- DSel=0 DScale=0 PME-