[Arm-dev] Cubieboard2 sata boot

Robert Moskowitz rgm at htt-consult.com
Mon Aug 31 00:54:03 UTC 2015


I am booted off sata by doing the following:

I took David's image:

http://www.mininodes.com/uploads/cubieboard2-centos-image.img.tar.gz

And first dd it to a 4Gb mSD card.  I used gparted to delete all three 
partitions.  This way I was assured to get the uboot David used.

Then I dd it to a 80Gb sata drive.  I use gparted to increase the size 
of the / partition.

I put the uboot only mSD card in the slot and attached to sata drive and 
it booted right up.  Here is what the serial console showed.

U-Boot SPL 2015.07-rc1-00513-g5bcec54 (Jun 17 2015 - 13:48:34)
DRAM: 1024 MiB
CPU: 912000000Hz, AXI/AHB/APB: 3/2/2


U-Boot 2015.07-rc1-00513-g5bcec54 (Jun 17 2015 - 13:48:34 +0530) 
Allwinner Techn
ology

CPU:   Allwinner A20 (SUN7I)
I2C:   ready
DRAM:  1 GiB
MMC:   SUNXI SD/MMC: 0
*** Warning - bad CRC, using default environment

HDMI connected: Setting up a 1920x1080 hdmi console
In:    serial
Out:   vga
Err:   vga
SCSI:  SUNXI SCSI INIT
Target spinup took 0 ms.
AHCI 0001.0100 32 slots 1 ports 3 Gbps 0x1 impl SATA mode
flags: ncq stag pm led clo only pmp pio slum part ccc apst
Net:   eth0: ethernet at 01c50000
starting USB...
USB0:   USB EHCI 1.00
USB1:   USB OHCI 1.0
USB2:   USB EHCI 1.00
USB3:   USB OHCI 1.0
scanning bus 0 for devices... 1 USB Device(s) found
scanning bus 2 for devices... 1 USB Device(s) found
scanning bus 1 for devices... 2 USB Device(s) found
scanning bus 3 for devices... 1 USB Device(s) found
Hit any key to stop autoboot:  0
switch to partitions #0, OK
mmc0 is current device
** Invalid partition 1 **
scanning bus for devices...
   Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0
             Type: Hard Disk
             Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
Found 1 device(s).

SCSI device 0:
     Device 0: (0:0) Vendor: ATA Prod.: WDC WD800BEVS-75 Rev: 04.0
             Type: Hard Disk
             Capacity: 76319.0 MB = 74.5 GB (156301488 x 512)
... is now current device
Scanning scsi 0:1...
Found /extlinux/extlinux.conf
Retrieving file: /extlinux/extlinux.conf
327 bytes read in 57 ms (4.9 KiB/s)
Ignoring unknown command: ui
Ignoring malformed menu command:  autoboot
Ignoring unknown command: totaltimeout
centos Options
1:    centos
Enter choice: 1:    centos
Retrieving file: /initramfs-4.0.0-1.el7.armv7hl.img
66687488 bytes read in 1838 ms (34.6 MiB/s)
Retrieving file: /vmlinuz-4.0.0-1.el7.armv7hl


and so forth.

So looks good.




More information about the Arm-dev mailing list