[CentOS-virt] How to manually add a new interface to a bridge device?

Howard Leadmon

howard at leadmon.net
Wed Dec 9 08:55:44 UTC 2015


Tried that as well, but this has to be something that gets set at the OS level and loaded, as if you look at dmesg output, you can see all the vnet?? nodes as the OS comes online.    So the question is, what is virt-install doing that creates the needed vnet interface that is part of the bridge.   I really had to kill and reload the VM just to load a second interface..

 

 

---

Howard Leadmon 

 

From: centos-virt-bounces at centos.org [mailto:centos-virt-bounces at centos.org] On Behalf Of Zoltan Frombach
Sent: Wednesday, December 9, 2015 2:42 AM
To: Discussion about the virtualization on CentOS <centos-virt at centos.org>
Subject: Re: [CentOS-virt] How to manually add a new interface to a bridge device?

 

I would stop the VM, edit its definition file (that's an XML file) and then start it up. But be careful: After you edit the XML file, you need to execute a command so KVM re-reads that file. I forgot that command, but you can look it up on Google.

On Dec 9, 2015 7:52 AM, "Howard Leadmon" <howard at leadmon.net <mailto:howard at leadmon.net> > wrote:

 

Maybe my google-fu is failing me, but I have spent the past couple hours looking at how to add a vnet? Device to my KVM host running CentOS 6, and for the life of me I can’t get this going.    

 

>From all my research if I want to add a device I should just do ‘brctl addif br1 vnet14’ if I want to add a vnet14 to bridge br1.   When I do this, I get:

 

# brctl addif br0 vnet14

interface vnet14 does not exist!

 

 

If I run a ‘brctl show’ I get the following:

 

# brctl show

bridge name     bridge id               STP enabled     interfaces

br0             8000.00237dd22a4c       no              eth0

                                                        vnet0

                                                        vnet10

                                                        vnet11

                                                        vnet13

                                                        vnet2

                                                       vnet3

                                                        vnet4

                                                        vnet6

                                                        vnet8

br1             8000.00237dd22a50       no              eth1

                                                        vnet1

                                                        vnet12

                                                        vnet5

                                                        vnet7

                                                        vnet9

 

 

Needless to say the existing vnet?? Devices are in use on guest VM’s currently.

 

When I create a new VM using virt-install, I usually add the following to my command line:

 

--network=bridge:br0 --network=bridge:br1

 

I messed up building a new VM, and only added the br0 interface to the VM, but need the br1 interface as well.  So my question is, or a pointer to how I can add that br1 interface to my existing VM, and create the needed vnet14 interface for it to attach to?

 

If anyone can explain how to do this, or give me a good pointer on where the info is on how to do this, it would sure be a huge help..

 

Thanks…

 

 

---

Howard Leadmon 

 


_______________________________________________
CentOS-virt mailing list
CentOS-virt at centos.org <mailto:CentOS-virt at centos.org> 
https://lists.centos.org/mailman/listinfo/centos-virt

-------------- next part --------------
An HTML attachment was scrubbed...
URL: <http://lists.centos.org/pipermail/centos-virt/attachments/20151209/5118b9a9/attachment-0002.html>


More information about the CentOS-virt mailing list