[CentOS] Can I install CentOS 4.2 on Sun X4100?

Sat Jan 7 12:21:19 UTC 2006
Sungsoo Kim <kiss at imageclick.com>

Dear Hughes,

Thank you for your reply!

As you metioned I installed device driver when I installed
RHEL 4.0 U1 by typing "linux dd" and inserting device driver CD
according to X4100's installation manual.

I just intalled RHES 4.0 U1, not updated anything.
So the running kernel version is kernel-smp-2.6.9-11.EL as shown below.

    [root at atlas ~]# uname -a
    Linux atlas 2.6.9-11.ELsmp #1 SMP Fri May 20 18:25:30 EDT 2005 x86_64 x86_64 x86_64 GNU/Linux

Thanks a lot!


Sungsoo Kim



----- Original Message ----- 
From: "Johnny Hughes" <mailing-lists at hughesjr.com>
To: "CentOS ML" <centos at centos.org>
Sent: Saturday, January 07, 2006 7:30 PM
Subject: Re: [CentOS] Can I install CentOS 4.2 on Sun X4100?

On Sat, 2006-01-07 at 12:47 +0900, Sungsoo Kim wrote:
> Hi, all!
> 
> I want to change current RHEL 4.0 ES  into CentOS 4.2 on Sun X4100 server.
> The server has SAS SCSI based two 2.5" hard disks.
> I could only install RHEL 4.0 Update 1 because the server is equipped with
> RHEL 4.0 Update 1's device driver only.
> 

This means that you installed a driver when you installed the OS ... do
you still have the RHEL kernel what shipped with update 1 .. or have you
upgraded the kernel since then.

Have you done any other updates (besides the kernel) since update 1?

What is the output of this command:

uname -a

> I've included below the boot process messages concerned with SCSI controller.
> If it's possible for me to install CentOS 4.0 on my X4100, I am ready to
> switch to it.
> 
> TIA
> 
> 
> Sungsoo Kim
> 
> 
> -------------------
> 
> SCSI subsystem initialized
> Fusion MPT base driver 3.02.18
> Copyright (c) 1999-2005 LSI Logic Corporation
> ACPI: PCI interrupt 0000:02:03.0[A] -> GSI 28 (level, low) -> IRQ 209
> mptbase: Initiating ioc0 bringup
> ioc0: SAS1064: Capabilities={Initiator}
> Fusion MPT SCSI Host driver 3.02.18
> scsi0 : ioc0: LSISAS1064, FwRev=01040000h, Ports=1, MaxQ=203, IRQ=209
>   Vendor: FUJITSU   Model: MAV2073RCSUN72G   Rev: 0301
>   Type:   Direct-Access                      ANSI SCSI revision: 04
> SCSI device sda: 143374738 512-byte hdwr sectors (73408 MB)
> SCSI device sda: drive cache: write through
>  sda: sda1 sda2 sda3
> Attached scsi disk sda at scsi0, channel 0, id 2, lun 0
>   Vendor: FUJITSU   Model: MAV2073RCSUN72G   Rev: 0301
>   Type:   Direct-Access                      ANSI SCSI revision: 04
> SCSI device sdb: 143374738 512-byte hdwr sectors (73408 MB)
> SCSI device sdb: drive cache: write through
>  sdb: sdb1
> Attached scsi disk sdb at scsi0, channel 0, id 3, lun 0
> _______________________________________________

More important than anything else is figuring out what kernel you need
to use.  There is a forzen CentOS-4.1 tree at http://vault.centos.org
that has all the 4.1 kernels.

(In CentOS ... 4.0 is the original release, 4.1 is update 1, 4.2 is
update 2, etc.)

After the kernel issues are defined, a plan for doing a switch can be
put together.  Is there a driver source so that you can build a new
driver for new kernels (if required)?