On Tue, 2006-05-02 at 17:56 -0700, Steven Vishoot wrote: > > --- Craig White <craigwhite at azapple.com> wrote: > > > I have an issue with cdrecord though and I can't > > figure it out. I use > > Webmin, which basically just creates an iso and then > > uses cdrecord to > > burn it and it worked fine with previously installed > > CentOS 4 (I wiped > > and reinstalled about 8 months ago). > > > > This is the command that Webmin tries to execute... > > > > cdrecord -v dev=0,0,0 speed=4 -isosize \ > > '/home/Linux/CentOS-4/CentOS-4.2-i386-bin4of4.iso' > > > > The result of cdrecord -scanbus at bottom of email. > > Log of error just > > below. > > > > Help appreciated... > > > > Craig > > > > cdrecord: No write mode specified. > > cdrecord: Asuming -tao mode. > > cdrecord: Future versions of cdrecord may have > > different drive dependent defaults. > > cdrecord: Continuing in 5 seconds... > > scsidev: '0,0,0' > > scsibus: 0 target: 0 lun: 0 > > cdrecord: No such file or directory. Cannot open > > '/dev/pg0'. Cannot open SCSI driver. > > cdrecord: For possible targets try 'cdrecord > > -scanbus'. > > cdrecord: For possible transport specifiers try > > 'cdrecord dev=help'. > > Cdrecord-Clone 2.01-dvd (i686-pc-linux-gnu) > > Copyright (C) 1995-2004 Jörg Schilling > > Note: This version is an unofficial (modified) > > version with DVD support > > Note: and therefore may have bugs that are not > > present in the original. > > Note: Please send bug reports or support requests to > > http://bugzilla.redhat.com/bugzilla > > Note: The author of cdrecord should not be bothered > > with problems in this version. > > TOC Type: 1 = CD-ROM > > > > # cdrecord -scanbus > > Cdrecord-Clone 2.01-dvd (i686-pc-linux-gnu) > > Copyright (C) 1995-2004 J�rg > > Schilling > > Note: This version is an unofficial (modified) > > version with DVD support > > Note: and therefore may have bugs that are not > > present in the original. > > Note: Please send bug reports or support requests to > > http://bugzilla.redhat.com/bugzilla > > Note: The author of cdrecord should not be bothered > > with problems in > > this version. > > scsidev: 'ATA' > > devname: 'ATA' > > scsibus: -2 target: -2 lun: -2 > > Linux sg driver version: 3.5.27 > > Using libscg version 'schily-0.8'. > > cdrecord: Warning: using inofficial libscg transport > > code version > > (schily - Red Hat-scsi-linux-sg.c-1.83-RH > > '@(#)scsi-linux-sg.c > > 1.83 04/05/20 Copyright 1997 J. Schilling'). > > scsibus0: > > 0,0,0 0) 'COMBI ' 'RW16x10/DVD ' > > 'H1.1' Removable > > CD-ROM > > 0,1,0 1) * > > 0,2,0 2) * > > 0,3,0 3) * > > 0,4,0 4) * > > 0,5,0 5) * > > 0,6,0 6) * > > 0,7,0 7) * > > > > > > _______________________________________________ > > CentOS mailing list > > CentOS at centos.org > > http://lists.centos.org/mailman/listinfo/centos > > > craig, > > the only time i have had troubles like that is when > the ide-cd would load before the ide-scsi. check to > see if both ide-scsi and ide-cd are loaded....but not > sure if this is your problem.. can not remember if i > was able to see the drive when this happened to me. ---- neither were loaded according to lsmod I modprobed ide-scsi (didn't change anything) same error as above I modprobed ide-cd (error) # modprobe ide-cd FATAL: Module ide_cd not found. Craig