Ross S. W. Walker wrote: >> -----Original Message----- >> From: centos-bounces at centos.org >> [mailto:centos-bounces at centos.org] On Behalf Of Ruslan Sivak >> Sent: Monday, May 07, 2007 4:00 PM >> To: CentOS mailing list >> Subject: Re: [CentOS] Anaconda doesn't support raid10 >> >> Ross S. W. Walker wrote: >> >>>> -----Original Message----- >>>> From: centos-bounces at centos.org >>>> [mailto:centos-bounces at centos.org] On Behalf Of Ruslan Sivak >>>> Sent: Monday, May 07, 2007 12:53 PM >>>> To: CentOS mailing list >>>> Subject: [CentOS] Anaconda doesn't support raid10 >>>> >>>> So after troubleshooting this for about a week, I was >>>> >> finally able to >> >>>> create a raid 10 device by installing the system, copying the >>>> md modules >>>> onto a floppy, and loading the raid10 module during the install. >>>> >>>> Now the problem is that I can't get it to show up in anaconda. It >>>> detects the other arrays (raid0 and raid1) fine, but the >>>> >> raid10 array >> >>>> won't show up. Looking through the logs (Alt-F3), I see the >>>> following >>>> warning: >>>> >>>> WARNING: raid level RAID10 not supported, skipping md10. >>>> >>>> I'm starting to hate the installer more and more. Why won't >>>> it let me >>>> install on this device, even though it's working perfectly >>>> >> from the >> >>>> shell? Why am I the only one having this problem? Is nobody >>>> out there >>>> using md based raid10? >>>> >>>> >>> Most people install the OS on a 2 disk raid1, then create a separate >>> raid10 for data storage. >>> >>> Anaconda was never designed to create RAID5/RAID10 during install. >>> >>> -Ross >>> >>> >>> >> Whether or not it was designed to create a Raid5/raid10, it >> allows the >> creating of raid5 and raid6 during install. It doesn't, >> however, allow >> the use of raid10 even if it's created in the shell outside >> of anaconda >> (or if you have an old installation on a raid10). >> >> I've just installed the system as follows >> >> Raid1 for /boot with 2 spares (200mb) >> raid0 for swap (1GB) >> raid6 for / (10GB) >> >> after installing, I was able to create a raid10 device and >> successfully >> mount and automount by using /etc/fstab >> >> Now to test what happens when a drive fails. I pulled out the first >> drive - Box refuses to boot. Going into rescue mode, I was able to >> mount /boot, was not able to mount the swap drive (as to be >> expected, as >> it's a raid0), was also not able to mount the / for some >> reason, which >> is a little surprising. >> >> I was able to mount the raid10 parition just fine. >> >> Maybe I messed up somewhere along the line. I'll try again, but it's >> disheartening to see that a raid6 array would die after one drive >> failure, even if it was somehow my fault. >> >> Also assuming that the raid5 array could be recovered, what >> would I do >> with the swap partition? Would I just recreate it from the >> space in the >> leftover drives and would that be all that I need to boot? >> > > Ok, my bad raid5/6 can be created during install even if OS > can't boot from it. > > I guess raid10 is the red headed stepchild of anaconda... > > I suggest this: > > /dev/md0 raid1, 128MB partition, all 4 drives, for /boot > /dev/md1 raid1, rest of drive space, first 2 drives, for lvm > /dev/md2 raid1, rest of drive space, second 2 drives, for lvm > > lvm volgroup CentOS, comprised of /dev/md1 and /dev/md2 > logical vol1, root, interleave 2, mount /, 16GB > logical vol2, swap, interleave 2, swapfs, 4GB > > This will provide the same performance and fail-over as a raid10. > > If you remove the first disk and boot make sure BIOS is set to boot > off of disk2! > > -Ross > > _____________________________________________________________________ > I don't seem to be able to control the interleave through anaconda. Is this something that can be done post install? Also I'm not very comfortable using LVM yet. Just getting used to md. Russ