[CentOS] USB device not connected (CentOS 5.3)

Tue Apr 28 22:11:12 UTC 2009
Bart Schaefer <barton.schaefer at gmail.com>

I just tried this with CentOS 5.3 as well, and got exactly the same
symptoms and dmesg output.  (As a point of comparison, Ubunu 8.04 on
my work laptop is able to access the drive.)

Obviously "not detected" is a misapprehension, though I'm puzzled why
"lsusb" doesn't show it.  The device is there even though the
partition table can't be read.

---------- Forwarded message ----------
From: Bart Schaefer <barton.schaefer at gmail.com>
Date: Tue, Apr 28, 2009 at 10:58 AM
Subject: Re: [CentOS] USB device not detected (CentOS 4.7)
To: CentOS mailing list <centos at centos.org>


On Tue, Apr 28, 2009 at 10:01 AM, Craig White <craigwhite at azapple.com> wrote:
> On Tue, 2009-04-28 at 09:48 -0700, Bart Schaefer wrote:
>> I recently purchased an I/O Magic USB enclosure for 3.5" IDE
> ----
> check what it says about the drive in dmesg after you plugged it in.

Hmm.

usb 1-6: new high speed USB device using address 4
scsi7 : SCSI emulation for USB Mass Storage devices
 Vendor: HDS72251  Model: 6VLAT80           Rev:  0 0
 Type:   Direct-Access                      ANSI SCSI revision: 02
SCSI device sdd: 321672960 512-byte hdwr sectors (164697 MB)
sdd: assuming drive cache: write through
SCSI device sdd: 321672960 512-byte hdwr sectors (164697 MB)
sdd: assuming drive cache: write through

(so far this is correct, it's a 160GB drive in the enclosure)
(the leading space on the next line is literally there in dmesg)

 sdd:SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
ldm_validate_partition_table(): Disk read failed.
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
 unable to read partition table
Attached scsi disk sdd at scsi7, channel 0, id 0, lun 0
USB Mass Storage device found at 4
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 0
Buffer I/O error on device sdd, logical block 0
SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 8
Buffer I/O error on device sdd, logical block 1

(the last three lines then repeat for each of sectors 16-568, logical
blocks 2-71)

SCSI error : <7 0 0 0> return code = 0x10070000
end_request: I/O error, dev sdd, sector 512
Buffer I/O error on device sdd, logical block 64
usb 1-6: USB disconnect, address 4

(that's where I unplugged)