I have a centos box with 3 nics. eth0 is internal, eth1 is T1 data and eth2 is cable data. Everything is working on eth2 cable. External NAT is working just fine for eth2. However external address 74.x.x.x on eth1 is not working. Below is my iptables information. I setup eth1 same as eth2 just a different IP address of course. What did I miss that eth1 and NAT is not working? Just looking for both public IP's incoming to NAT to the correct IP address. Only 1 is working at this time. Thanks, Jerry --------------- Chain INPUT (policy ACCEPT) target prot opt source destination RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0 Chain FORWARD (policy ACCEPT) target prot opt source destination RH-Firewall-1-INPUT all -- 0.0.0.0/0 0.0.0.0/0 Chain OUTPUT (policy ACCEPT) target prot opt source destination Chain RH-Firewall-1-INPUT (2 references) target prot opt source destination ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 ACCEPT icmp -- 0.0.0.0/0 0.0.0.0/0 icmp type 255 ACCEPT esp -- 0.0.0.0/0 0.0.0.0/0 ACCEPT ah -- 0.0.0.0/0 0.0.0.0/0 ACCEPT udp -- 0.0.0.0/0 224.0.0.251 udp dpt:5353 ACCEPT udp -- 0.0.0.0/0 0.0.0.0/0 udp dpt:631 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 tcp dpt:631 ACCEPT all -- 0.0.0.0/0 0.0.0.0/0 state RELATED,ESTABLISHED ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:25 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:22 ACCEPT tcp -- 0.0.0.0/0 0.0.0.0/0 state NEW tcp dpt:80 REJECT all -- 0.0.0.0/0 0.0.0.0/0 reject-with icmp-host-prohibited Chain PREROUTING (policy ACCEPT) target prot opt source destination DNAT tcp -- 0.0.0.0/0 24.123.23.170 tcp dpt:22 to:192.168.1.209:22 DNAT tcp -- 0.0.0.0/0 24.123.23.170 tcp dpt:25 to:192.168.1.209:25 DNAT tcp -- 0.0.0.0/0 24.123.23.170 tcp dpt:80 to:192.168.1.209:80 DNAT tcp -- 0.0.0.0/0 74.223.8.179 tcp dpt:22 to:192.168.1.58:22 DNAT tcp -- 0.0.0.0/0 74.223.8.179 tcp dpt:25 to:192.168.1.58:25 DNAT tcp -- 0.0.0.0/0 74.223.8.179 tcp dpt:80 to:192.168.1.58:80 Chain POSTROUTING (policy ACCEPT) target prot opt source destination SNAT all -- 192.168.1.0/24 0.0.0.0/0 to:24.123.23.170 SNAT all -- 0.0.0.0/0 192.168.1.209 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.209 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.209 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.209 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.209 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.209 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.58 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.58 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.58 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.58 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.58 to:192.168.1.1 SNAT all -- 0.0.0.0/0 192.168.1.58 to:192.168.1.1 Chain OUTPUT (policy ACCEPT) target prot opt source destination Kernel IP routing table Destination Gateway Genmask Flags Metric Ref Use Iface 24.123.23.168 0.0.0.0 255.255.255.248 U 0 0 0 eth2 74.223.8.176 0.0.0.0 255.255.255.240 U 0 0 0 eth1 192.168.1.0 0.0.0.0 255.255.255.0 U 0 0 0 eth0 169.254.0.0 0.0.0.0 255.255.0.0 U 0 0 0 eth2 0.0.0.0 24.123.23.169 0.0.0.0 UG 0 0 0 eth2