On the 2nd try it has booted and seems to work.
The /var/log/mcelog is (and was) empty.
# sudo cat /proc/mdstat
Personalities : [raid1]
md0 : active raid1 sdb1[1] sda1[0]
1023936 blocks [2/2] [UU]
md2 : active raid1 sdb5[1] sda5[0]
277728192 blocks [2/2] [UU]
md3 : active raid1 sdb6[1] sda6[0]
185151360 blocks [2/2] [UU]
md1 : active raid1 sdb3[1] sda3[0]
20479936 blocks [2/2] [UU]
unused devices: <none>
Below is the output from the remote console of my hoster.
If you notice anything or have any advice, please share.
GNU GRUB version 0.97 (636K lower / 3635904K upper memory)
+-------------------------------------------------------------------------+
| CentOS (2.6.18-238.9.1.el5) |
| CentOS (2.6.18-238.5.1.el5) |
| CentOS (2.6.18-194.32.1.el5) |
| CentOS 5 |
| CentOS 5 Disk 2 |
| |
| |
| |
| |
| |
| |
| |
+-------------------------------------------------------------------------+
Use the ^ and v keys to select which entry is highlighted.
Press enter to boot the selected OS, 'e' to edit the
commands before booting, 'a' to modify the kernel arguments
before booting, or 'c' for a command-line.
The highlighted entry will be booted automatically in 1 seconds.
Booting 'CentOS (2.6.18-238.9.1.el5)'
root (hd0,0)
Filesystem type is ext2fs, partition type 0xfd
kernel /vmlinuz-2.6.18-238.9.1.el5 root=/dev/md1 console=tty0 console=ttyS0,576
00
[Linux-bzImage, setup=0x1e00, size=0x1fd9fc]
initrd /initrd-2.6.18-238.9.1.el5.img
[Linux-initrd @ 0x37d5f000, 0x290aac bytes]
Linux version 2.6.18-238.9.1.el5 (mockbuild at builder10.centos.org) (gcc
version 4.1.2 20080704 (Red Hat 4.1.2-50)) #1 SMP Tue Apr 12 18:10:13
EDT 2011
Command line: root=/dev/md1 console=tty0 console=ttyS0,57600
BIOS-provided physical RAM map:
BIOS-e820: 0000000000010000 - 000000000009f000 (usable)
BIOS-e820: 000000000009f000 - 00000000000a0000 (reserved)
BIOS-e820: 00000000000e4000 - 0000000000100000 (reserved)
BIOS-e820: 0000000000100000 - 00000000ddfb0000 (usable)
BIOS-e820: 00000000ddfb0000 - 00000000ddfbe000 (ACPI data)
BIOS-e820: 00000000ddfbe000 - 00000000ddfe0000 (ACPI NVS)
BIOS-e820: 00000000ddfe0000 - 00000000ddfee000 (reserved)
BIOS-e820: 00000000ddff0000 - 00000000de000000 (reserved)
BIOS-e820: 00000000ff700000 - 0000000100000000 (reserved)
BIOS-e820: 0000000100000000 - 0000000120000000 (usable)
DMI present.
No NUMA configuration found
Faking a node at 0000000000000000-0000000120000000
Bootmem setup node 0 0000000000000000-0000000120000000
Memory for crash kernel (0x0 to 0x0) notwithin permissible range
disabling kdump
ACPI: PM-Timer IO Port: 0x808
ACPI: LAPIC (acpi_id[0x01] lapic_id[0x00] enabled)
Processor #0 0:4 APIC version 16
ACPI: LAPIC (acpi_id[0x02] lapic_id[0x01] enabled)
Processor #1 0:4 APIC version 16
ACPI: LAPIC (acpi_id[0x03] lapic_id[0x02] enabled)
Processor #2 0:4 APIC version 16
ACPI: LAPIC (acpi_id[0x04] lapic_id[0x03] enabled)
Processor #3 0:4 APIC version 16
ACPI: IOAPIC (id[0x04] address[0xfec00000] gsi_base[0])
IOAPIC[0]: apic_id 4, version 33, address 0xfec00000, GSI 0-23
ACPI: INT_SRC_OVR (bus 0 bus_irq 0 global_irq 2 dfl dfl)
ACPI: INT_SRC_OVR (bus 0 bus_irq 9 global_irq 9 low level)
Setting APIC routing to flat
ACPI: HPET id: 0x8300 base: 0xfed00000
Using ACPI (MADT) for SMP configuration information
Nosave address range: 000000000009f000 - 00000000000a0000
Nosave address range: 00000000000a0000 - 00000000000e4000
Nosave address range: 00000000000e4000 - 0000000000100000
Nosave address range: 00000000ddfb0000 - 00000000ddfbe000
Nosave address range: 00000000ddfbe000 - 00000000ddfe0000
Nosave address range: 00000000ddfe0000 - 00000000ddfee000
Nosave address range: 00000000ddfee000 - 00000000ddff0000
Nosave address range: 00000000ddff0000 - 00000000de000000
Nosave address range: 00000000de000000 - 00000000ff700000
Nosave address range: 00000000ff700000 - 0000000100000000
Allocating PCI resources starting at e0000000 (gap: de000000:21700000)
SMP: Allowing 4 CPUs, 0 hotplug CPUs
Built 1 zonelists. Total pages: 1022573
Kernel command line: root=/dev/md1 console=tty0 console=ttyS0,57600
Initializing CPU#0
PID hash table entries: 4096 (order: 12, 32768 bytes)
Console: colour VGA+ 80x25
Dentry cache hash table entries: 524288 (order: 10, 4194304 bytes)
Inode-cache hash table entries: 262144 (order: 9, 2097152 bytes)
Checking aperture...
CPU 0: aperture @ 449c000000 size 32 MB
Aperture too small (32 MB)
No AGP bridge found
Your BIOS doesn't leave a aperture memory hole
Please enable the IOMMU option in the BIOS setup
This costs you 64 MB of RAM
Mapping aperture over 65536 KB of RAM @ 4000000
Nosave address range: 0000000004000000 - 0000000008000000
ACPI: DMAR not present
Memory: 4015428k/4718592k available (2592k kernel code, 145336k
reserved, 1653k data, 224k init)
Calibrating delay loop (skipped), value calculated using timer
frequency.. 5000.22 BogoMIPS (lpj=2500114)
Security Framework v1.0.0 initialized
SELinux: Initializing.
selinux_register_security: Registering secondary module capability
Capability LSM initialized as secondary
Mount-cache hash table entries: 256
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 0/0 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 0
SMP alternatives: switching to UP code
ACPI: Core revision 20060707
Using local APIC timer interrupts.
Detected 12.500 MHz APIC timer.
SMP alternatives: switching to SMP code
Booting processor 1/4 APIC 0x1
Initializing CPU#1
Calibrating delay using timer specific routine.. 5000.09 BogoMIPS (lpj=2500048)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 1/1 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 1
Quad-Core AMD Opteron(tm) Processor 1381 stepping 02
SMP alternatives: switching to SMP code
Booting processor 2/4 APIC 0x2
Initializing CPU#2
Calibrating delay using timer specific routine.. 4999.72 BogoMIPS (lpj=2499862)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 2/2 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 2
Quad-Core AMD Opteron(tm) Processor 1381 stepping 02
SMP alternatives: switching to SMP code
Booting processor 3/4 APIC 0x3
Initializing CPU#3
Calibrating delay using timer specific routine.. 4999.68 BogoMIPS (lpj=2499842)
CPU: L1 I Cache: 64K (64 bytes/line), D cache 64K (64 bytes/line)
CPU: L2 Cache: 512K (64 bytes/line)
CPU 3/3 -> Node 0
CPU: Physical Processor ID: 0
CPU: Processor Core ID: 3
Quad-Core AMD Opteron(tm) Processor 1381 stepping 02
Brought up 4 CPUs
NMI watchdog testing PASSED.
time.c: Using 14.318180 MHz WALL HPET GTOD HPET/TSC timer.
time.c: Detected 2500.117 MHz processor.
migration_cost=246
checking if image is initramfs... it is
Freeing initrd memory: 2626k freed
NET: Registered protocol family 16
ACPI: bus type pci registered
PCI: BIOS Bug: MCFG area at e0000000 is not E820-reserved
PCI: Not using MMCONFIG.
PCI: Using configuration type 1
PCI: Using configuration type 1 for extended access
ACPI: Interpreter enabled
ACPI: Using IOAPIC for interrupt routing
ACPI: No dock devices found.
ACPI: PCI Root Bridge [PCI0] (0000:00)
PCI: set SATA to AHCI mode
PCI: Ignoring BAR0-3 of IDE controller 0000:00:14.1
PCI: Transparent bridge - 0000:00:14.4
ACPI: PCI Interrupt Link [LNKA] (IRQs 3 4 *5 7 10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKB] (IRQs 3 4 5 7 10 11 12 14 *15)
ACPI: PCI Interrupt Link [LNKC] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKD] (IRQs 3 4 5 7 *10 11 12 14 15)
ACPI: PCI Interrupt Link [LNKE] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
ACPI: PCI Interrupt Link [LNKF] (IRQs 9) *0, disabled.
ACPI: PCI Interrupt Link [LNKG] (IRQs 3 4 5 7 10 *11 12 14 15)
ACPI: PCI Interrupt Link [LNKH] (IRQs 3 4 5 7 10 11 12 14 15) *0, disabled.
Linux Plug and Play Support v0.97 (c) Adam Belay
pnp: PnP ACPI init
pnp: PnP ACPI: found 14 devices
usbcore: registered new driver usbfs
usbcore: registered new driver hub
PCI: Using ACPI for IRQ routing
PCI: If a device doesn't work, try "pci=routeirq". If it helps, post a report
PCI: Cannot allocate resource region 1 of device 0000:00:14.0
NetLabel: Initializing
NetLabel: domain hash size = 128
NetLabel: protocols = UNLABELED CIPSOv4
NetLabel: unlabeled traffic allowed by default
hpet0: at MMIO 0xfed00000 (virtual 0xffffffffff5fe000), IRQs 2, 8, 0, 0
hpet0: 4 32-bit timers, 14318180 Hz
ACPI: DMAR not present
PCI-DMA: Disabling AGP.
PCI-DMA: aperture base @ 4000000 size 65536 KB
PCI-DMA: using GART IOMMU.
PCI-DMA: Reserving 64MB of IOMMU area in the AGP aperture
pnp: 00:08: iomem range 0xfec00000-0xfec00fff has been reserved
pnp: 00:08: iomem range 0xfee00000-0xfee00fff has been reserved
pnp: 00:09: iomem range 0xffb80000-0xffbfffff could not be reserved
pnp: 00:0b: ioport range 0xa00-0xa0f has been reserved
pnp: 00:0b: ioport range 0xa10-0xa1f has been reserved
pnp: 00:0c: iomem range 0xe0000000-0xefffffff has been reserved
pnp: 00:0d: iomem range 0x0-0x9ffff could not be reserved
pnp: 00:0d: iomem range 0xc0000-0xcffff could not be reserved
pnp: 00:0d: iomem range 0xe0000-0xfffff could not be reserved
pnp: 00:0d: iomem range 0x100000-0xddffffff could not be reserved
PCI: Error while updating region 0000:00:14.0/1 (f0000004 != 8000a014)
PCI: Bridge: 0000:00:01.0
IO window: c000-cfff
MEM window: fe800000-fe9fffff
PREFETCH window 0x00000000fc000000-0x00000000fdffffff
PCI: Bridge: 0000:00:04.0
IO window: d000-dfff
MEM window: fea00000-feafffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:05.0
IO window: e000-efff
MEM window: feb00000-febfffff
PREFETCH window: disabled.
PCI: Bridge: 0000:00:14.4
IO window: disabled.
MEM window: disabled.
PREFETCH window: disabled.
NET: Registered protocol family 2
IP route cache hash table entries: 131072 (order: 8, 1048576 bytes)
TCP established hash table entries: 262144 (order: 10, 4194304 bytes)
TCP bind hash table entries: 65536 (order: 8, 1048576 bytes)
TCP: Hash tables configured (established 262144 bind 65536)
TCP reno registered
audit: initializing netlink socket (disabled)
type=2000 audit(1304023514.497:1): initialized
Total HugeTLB memory allocated, 0
VFS: Disk quotas dquot_6.5.1
Dquot-cache hash table entries: 512 (order 0, 4096 bytes)
Initializing Cryptographic API
alg: No test for crc32c (crc32c-generic)
ksign: Installing public key data
Loading keyring
- Added public key C2DDC58DBBE93568
- User ID: CentOS (Kernel Module GPG key)
io scheduler noop registered
io scheduler anticipatory registered
io scheduler deadline registered
io scheduler cfq registered (default)
pci_hotplug: PCI Hot Plug PCI Core version: 0.5
ACPI: duty_cycle spans bit 4
Real Time Clock Driver v1.12ac
Non-volatile memory driver v1.2
Linux agpgart interface v0.101 (c) Dave Jones
Serial: 8250/16550 driver $Revision: 1.90 $ 4 ports, IRQ sharing enabled
▒serial8250: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
serial8250: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
00:05: ttyS0 at I/O 0x3f8 (irq = 4) is a 16550A
00:06: ttyS1 at I/O 0x2f8 (irq = 3) is a 16550A
brd: module loaded
Uniform Multi-Platform E-IDE driver Revision: 7.00alpha2
ide: Assuming 33MHz system bus speed for PIO modes; override with idebus=xx
SB600_PATA: IDE controller at PCI slot 0000:00:14.1
GSI 16 sharing vector 0xC1 and IRQ 16
ACPI: PCI Interrupt 0000:00:14.1[A] -> GSI 16 (level, low) -> IRQ 193
SB600_PATA: chipset revision 0
SB600_PATA: not 100% native mode: will probe irqs later
ide0: BM-DMA at 0xff00-0xff07, BIOS settings: hda:pio, hdb:pio
ide-floppy driver 0.99.newide
usbcore: registered new driver hiddev
usbcore: registered new driver usbhid
drivers/usb/input/hid-core.c: v2.6:USB HID core driver
PNP: PS/2 Controller [PNP0303:PS2K] at 0x60,0x64 irq 1
PNP: PS/2 controller doesn't have AUX irq; using default 12
serio: i8042 KBD port at 0x60,0x64 irq 1
serio: i8042 AUX port at 0x60,0x64 irq 12
mice: PS/2 mouse device common for all mice
md: md driver 0.90.3 MAX_MD_DEVS=256, MD_SB_DISKS=27
md: bitmap version 4.39
TCP bic registered
Initializing IPsec netlink socket
NET: Registered protocol family 1
NET: Registered protocol family 17
ACPI: (supports S0 S1 S3 S4 S5)
Initalizing network drop monitor service
Freeing unused kernel memory: 224k freed
Write protecting the kernel read-only data: 520k
Red Hat nash version 5.1.19.6 starting
Mounting proc filesystem
Mounting sysfs filesystem
Creating /dev
Creating initial device nodes
Setting up hotplug.
Creating block device nodes.
LoGSI 17 sharing vector 0xC9 and IRQ 17
ading ehci-hcd.kACPI: PCI Interrupt 0000:00:13.5[D] -> o module
GSI 19 (level, low) -> IRQ 201
ehci_hcd 0000:00:13.5: EHCI Host Controller
ehci_hcd 0000:00:13.5: new USB bus registered, assigned bus number 1
ehci_hcd 0000:00:13.5: applying AMD SB600/SB700 USB freeze workaround
ehci_hcd 0000:00:13.5: debug port 1
ehci_hcd 0000:00:13.5: irq 201, io mem 0xfe7ff000
ehci_hcd 0000:00:13.5: USB 2.0 started, EHCI 1.00, driver 10 Dec 2004
usb usb1: configuration #1 chosen from 1 choice
hub 1-0:1.0: USB hub found
hub 1-0:1.0: 10 ports detected
Loading ohci-hcd.ko module
ACPI: PCI Interrupt 0000:00:13.0[A] -> GSI 16 (level, low) -> IRQ 193
ohci_hcd 0000:00:13.0: OHCI Host Controller
ohci_hcd 0000:00:13.0: new USB bus registered, assigned bus number 2
ohci_hcd 0000:00:13.0: irq 193, io mem 0xfe7fe000
usb usb2: configuration #1 chosen from 1 choice
hub 2-0:1.0: USB hub found
hub 2-0:1.0: 2 ports detected
GSI 18 sharing vector 0xD1 and IRQ 18
ACPI: PCI Interrupt 0000:00:13.1[B] -> GSI 17 (level, low) -> IRQ 209
ohci_hcd 0000:00:13.1: OHCI Host Controller
ohci_hcd 0000:00:13.1: new USB bus registered, assigned bus number 3
ohci_hcd 0000:00:13.1: irq 209, io mem 0xfe7fd000
usb usb3: configuration #1 chosen from 1 choice
hub 3-0:1.0: USB hub found
hub 3-0:1.0: 2 ports detected
GSI 19 sharing vector 0xD9 and IRQ 19
ACPI: PCI Interrupt 0000:00:13.2[C] -> GSI 18 (level, low) -> IRQ 217
ohci_hcd 0000:00:13.2: OHCI Host Controller
ohci_hcd 0000:00:13.2: new USB bus registered, assigned bus number 4
ohci_hcd 0000:00:13.2: irq 217, io mem 0xfe7fc000
usb usb4: configuration #1 chosen from 1 choice
hub 4-0:1.0: USB hub found
hub 4-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.3[B] -> GSI 17 (level, low) -> IRQ 209
ohci_hcd 0000:00:13.3: OHCI Host Controller
ohci_hcd 0000:00:13.3: new USB bus registered, assigned bus number 5
ohci_hcd 0000:00:13.3: irq 209, io mem 0xfe7fb000
usb usb5: configuration #1 chosen from 1 choice
hub 5-0:1.0: USB hub found
hub 5-0:1.0: 2 ports detected
ACPI: PCI Interrupt 0000:00:13.4[C] -> GSI 18 (level, low) -> IRQ 217
ohci_hcd 0000:00:13.4: OHCI Host Controller
ohci_hcd 0000:00:13.4: new USB bus registered, assigned bus number 6
ohci_hcd 0000:00:13.4: irq 217, io mem 0xfe7fa000
usb usb6: configuration #1 chosen from 1 choice
hub 6-0:1.0: USB hub found
hub 6-0:1.0: 2 ports detected
Loading uhci-hcd.ko module
USB Universal Host Controller Interface driver v3.0
Loading jbd.ko module
Loading ext3.ko module
Loading raid1.ko module
md: raid1 personality registered for level 1
Loading scsi_mod.ko module
SCSI subsystem initialized
Loading sd_mod.ko module
Loading libata.ko module
Loading ahci.ko module
GSI 20 sharing vector 0xE1 and IRQ 20
ACPI: PCI Interrupt 0000:00:12.0[A] -> GSI 22 (level, low) -> IRQ 225
ahci 0000:00:12.0: controller can't do 64bit DMA, forcing 32bit
ahci 0000:00:12.0: AHCI 0001.0100 32 slots 4 ports 3 Gbps 0xf impl SATA mode
ahci 0000:00:12.0: flags: ncq sntf ilck pm led clo pmp pio slum part
scsi0 : ahci
scsi1 : ahci
scsi2 : ahci
scsi3 : ahci
ata1: SATA max UDMA/133 abar m1024 at 0xfe7ff800 port 0xfe7ff900 irq 225
ata2: SATA max UDMA/133 abar m1024 at 0xfe7ff800 port 0xfe7ff980 irq 225
ata3: SATA max UDMA/133 abar m1024 at 0xfe7ff800 port 0xfe7ffa00 irq 225
ata4: SATA max UDMA/133 abar m1024 at 0xfe7ff800 port 0xfe7ffa80 irq 225
ata1: softreset failed (device not ready)
ata1: failed due to HW bug, retry pmp=0
ata1: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata1.00: ATA-8: Hitachi HDS721050CLA362, JP2OA39C, max UDMA/133
ata1.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
ata1.00: SB600 AHCI: limiting to 255 sectors per cmd
ata1.00: configured for UDMA/133
ata2: softreset failed (device not ready)
ata2: failed due to HW bug, retry pmp=0
ata2: SATA link up 3.0 Gbps (SStatus 123 SControl 300)
ata2.00: ATA-8: Hitachi HDS721050CLA362, JP2OA39C, max UDMA/133
ata2.00: 976773168 sectors, multi 16: LBA48 NCQ (depth 31/32)
ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
ata2.00: SB600 AHCI: limiting to 255 sectors per cmd
ata2.00: configured for UDMA/133
ata3: SATA link down (SStatus 0 SControl 300)
ata4: SATA link down (SStatus 0 SControl 300)
Vendor: ATA Model: Hitachi HDS72105 Rev: JP2O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
SCSI device sda: 976773168 512-byte hdwr sectors (500108 MB)
sda: Write Protect is off
SCSI device sda: drive cache: write back
sda: sda1 sda2 sda3 sda4 < sda5 sda6 >
sd 0:0:0:0: Attached scsi disk sda
Vendor: ATA Model: Hitachi HDS72105 Rev: JP2O
Type: Direct-Access ANSI SCSI revision: 05
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
SCSI device sdb: 976773168 512-byte hdwr sectors (500108 MB)
sdb: Write Protect is off
SCSI device sdb: drive cache: write back
sdb: sdb1 sdb2 sdb3 sdb4 < sdb5 sdb6 >
sd 1:0:0:0: Attached scsi disk sdb
Loading dm-mem-cache.ko module
Loading dm-mod.kdevice-mapper: uevent: version 1.0.3
o module
device-mapper: ioctl: 4.11.5-ioctl (2007-12-12) initialised: dm-devel at redhat.com
Loading dm-log.ko module
Loading dm-region_hash.ko module
Loading dm-mesdevice-mapper: dm-raid45: initialized v0.2594l
sage.ko module
Loading dm-raid45.ko module
Waiting for driver initialization.
Scanning and conmd: Autodetecting RAID arrays.
figuring dmraid supported devices
md: autorun ...
md: considering sdb6 ...
md: adding sdb6 ...
md: sdb5 has different UUID to sdb6
md: sdb3 has different UUID to sdb6
md: sdb1 has different UUID to sdb6
md: adding sda6 ...
md: sda5 has different UUID to sdb6
md: sda3 has different UUID to sdb6
md: sda1 has different UUID to sdb6
md: created md3
md: bind<sda6>
md: bind<sdb6>
md: running: <sdb6><sda6>
raid1: raid set md3 active with 2 out of 2 mirrors
md: considering sdb5 ...
md: adding sdb5 ...
md: sdb3 has different UUID to sdb5
md: sdb1 has different UUID to sdb5
md: adding sda5 ...
md: sda3 has different UUID to sdb5
md: sda1 has different UUID to sdb5
md: created md2
md: bind<sda5>
md: bind<sdb5>
md: running: <sdb5><sda5>
raid1: raid set md2 active with 2 out of 2 mirrors
md: considering sdb3 ...
md: adding sdb3 ...
md: sdb1 has different UUID to sdb3
md: adding sda3 ...
md: sda1 has different UUID to sdb3
md: created md1
md: bind<sda3>
md: bind<sdb3>
md: running: <sdb3><sda3>
raid1: raid set md1 active with 2 out of 2 mirrors
md: considering sdb1 ...
md: adding sdb1 ...
md: adding sda1 ...
md: created md0
md: bind<sda1>
md: bind<sdb1>
md: running: <sdb1><sda1>
raid1: raid set md0 active with 2 out of 2 mirrors
md: ... autorun DONE.
Trying to resume from /dev/sda2
No suspend signature on swap, not resuming.
Creating root device.
Mounting root filesystem.
EXT3-fs: INFO: recovery required on readonly filesystem.
EXT3-fs: write access will be enabled during recovery.
kjournald starting. Commit interval 5 seconds
EXT3-fs: md1: orphan cleanup on readonly fs
EXT3-fs: md1: 132 orphan inodes deleted
EXT3-fs: recovery complete.
EXT3-fs: mounted filesystem with ordered data mode.
Setting up other filesystems.
Setting up new root fs
no fstab.sys, mounting internal defaults
Switching to new root and running init.
unmounting old /dev
unmounting old /proc
unmounting old /sys
SELinux: Disabled at runtime.
type=1404 audit(1304023545.901:2): selinux=0 auid=4294967295 ses=4294967295
INIT: version 2.86 booting
Welcome to CentOS release 5.6 (Final)
Press 'I' to enter interactive startup.
Setting clock (localtime): Thu Apr 28 20:45:48 BST 2011 [ OK ]
Starting udev: [ OK ]
Loading default keymap (uk): [ OK ]
Setting hostname localhost.localdomain: [ OK ]
No devices found
Setting up Logical Volume Management: No volume groups found
[ OK ]
Checking filesystems
Checking all file systems.
[ OK ]
Remounting root filesystem in read-write mode: [ OK ]
Mounting local filesystems: [ OK ]
Enabling local filesystem quotas: [ OK ]
Enabling /etc/fstab swaps: [ OK ]
INIT: Entering runlevel: 3
Entering non-interactive startup
Starting background readahead: [ OK ]
Checking for hardware changes [ OK ]
Enabling ondemand cpu frequency scaling: [ OK ]
Applying iptables firewall rules: [ OK ]
Loading additional iptables modules: ip_conntrack_netbios_ns [ OK ]
Bringing up loopback interface: [ OK ]
Bringing up interface eth0:
Determining IP information for eth0... done.
[ OK ]
Bringing up interface eth1:
Determining IP information for eth1... failed; no link present. Check cable?
[FAILED]
Starting auditd: [ OK ]
Starting system logger: [ OK ]
Starting kernel logger: [ OK ]
Starting irqbalance: [ OK ]
Starting system message bus: [ OK ]
Starting acpi daemon: [ OK ]
Starting sshd: [ OK ]
ntpd: Synchronising with time server: [ OK ]
Starting ntpd: [ OK ]
Starting postgresql: Starting postgresql service: [ OK ]
[ OK ]
Starting sendmail: [ OK ]
Starting sm-client: [ OK ]
Starting fms: [ OK ]
Starting httpd: [ OK ]
Starting crond: [ OK ]
[ OK ] atd: [ OK ]
Starting yum-updatesd: [ OK ]
Starting HAL daemon: [ OK ]
Starting smartd: [ OK ]
CentOS release 5.6 (Final)
Kernel 2.6.18-238.9.1.el5 on an x86_64
hXXXX login: