[CentOS] st1000spex ethernet card and centos 6.2

Sat May 12 17:37:45 UTC 2012
Alexander Dalloz <ad+lists at uni-x.org>

Am 12.05.2012 18:59, schrieb Gregory P. Ennis:
> On 5/12/2012 11:39 AM, Gregory P. Ennis wrote:
>> OK, I do have lspci on this system;  I am going to it down and put the
>> st1000spex back in the slot, and will send the lspci out put after I
>> reboot.
>>
>> Greg
> is the eth cable plugged in all the way?
> _______________________________________________
> 
> Bob,
> 
> At this point i would sure take the fix if that were the problem.  I
> have the lights active on the mother board nic and the nic on the
> st1000spex.
> 
> Here are the facts of the scenario that I have with the st1000spex
> inserted in the pci-e slot :
> 
> lspci : 
> 01:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 03)
> 02:00.0 Ethernet controller: Realtek Semiconductor Co., Ltd.
> RTL8111/8168B PCI Express Gigabit Ethernet controller (rev 06)
> 
> The first entry references the mother board nic and the second
> references the st1000spex.  Since both of these cards seem to have the
> same chipset i would think this would be an easy thing to set up.
> 
> ifconfig only displays eth0, and does not display eth1
> 
> 
> When I execute the command :
> 
> service network restart
> 
> eth0 is removed and restarted
> 
> then I get :
> 
> Bringing up interface eth1:  Device eth1 does not seem to be present.
> delaying initialization.

Are both devices specified within /etc/udev/rules.d/70-persistent-net.rules?

> I have NetworkManager turned to off
> 
> I have /etc/sysconfig/networking/
> #PCI-E Slot #1
> #StarTech 10/100/1000
> #HWADDR=00:0A:CD:1E:4D:F6
> DEVICE=eth1
> NAME="Internal Facing Network eth1"
> ONBOOT=yes
> NM_CONTROLLED=no
> TYPE=Ethernet
> BOOTPROTO=none
> IPV4_FAILURE_FATAL=yes
> IPV6INIT=no
> DEFROUTE=yes
> IPADDR=10.0.0.134
> NETMASK=255.255.255.0
> DNS1=127.0.0.1
> DOMAIN="pomec.net"
> UUID=4f637674-df3f-4fa8-a81a-8259563a1b1f
> PREFIX=24
> USERCTL=no
> 
> 
> I have /etc/sysconfig/network-scripts/icfg-eth1
> 
> set to :
> 
> #PCI-E Slot #1
> #StarTech 10/100/1000
> #HWADDR=00:0A:CD:1E:4D:F6
> DEVICE=eth1
> NAME="Internal Facing Network eth1"
> ONBOOT=yes
> NM_CONTROLLED=no
> TYPE=Ethernet
> BOOTPROTO=none
> IPV4_FAILURE_FATAL=yes
> IPV6INIT=no
> DEFROUTE=yes
> IPADDR=10.0.0.134
> NETMASK=255.255.255.0
> DNS1=127.0.0.1
> DOMAIN="pomec.net"
> UUID=4f637674-df3f-4fa8-a81a-8259563a1b1f
> PREFIX=24
> USERCTL=no

Alexander