On Tue, Nov 8, 2016 at 8:02 AM, Boris Epstein <borepstein at gmail.com> wrote: > Hello there, > > What is the hypervisor that hosts the VM? What does ifconfig show on it? > > Boris. > > On Mon, Nov 7, 2016 at 4:36 PM, Gordon Messmer <gordon.messmer at gmail.com> > wrote: > > > On 11/06/2016 11:00 PM, Sean Son wrote: > > > >> How do I > >> configure the networking so that both IPs are pingable and the VM is > >> reachable via both IPs? > >> > > > > > > You need one rule file per interface, which directs traffic out the > > appropriate interface based on the source address of the packet: > > > > https://blogs.oracle.com/networking/entry/advance_ > routing_for_multi_homed > > > > _______________________________________________ > > CentOS mailing list > > CentOS at centos.org > > https://lists.centos.org/mailman/listinfo/centos > > > _______________________________________________ > CentOS mailing list > CentOS at centos.org > https://lists.centos.org/mailman/listinfo/centos > Hello all Thank you for the replies. I ran into some issues with the policy based routing which I will explain in a few. First off to answer each one of your questions: Digimer: No I didnt take a look at IPTables Peter Brady: Thank you for the example, I tried that but it failed and I will explain in a minute. Frank Cox : That works but how do I make it persistent across reboots? Boris Epstein: I am using Hyper-V and its getting annoying lol Ok so here is how I have set everything up: my /etc/iproute2/rt_tables: # # reserved values # 255 local 254 main 253 default 0 unspec # # local # #1 inr.ruhep 300 NIC1 310 NIC2 my /etc/sysconfig/network-scripts/route-eth0 file: 168.87.147.0/24 dev eth0 table 300 default via 168.87.147.1 dev eth0 table 300 /etc/sysconfig/network-scripts/route-eth1 file: 10.20.50.0/24 dev eth1 table 310 default via 10.20.50.1 dev eth1 table 310 My /etc/sysconfig/network-scripts/rule-eth0: from 168.87.147.33/32 table 300 to 168.87.147.33 table 300 My /etc/sysconfig/network-scripts/rule-eth1: from 10.20.50.90/32 table 310 to 10.20.50.90 table 310 now after implementing this and restarting NetworkManager, when I run 'ip rule list', I get the following: 0: from all lookup local 32764: from all to 10.20.50.90 lookup NIC2 32765: from 10.20.50.90 lookup NIC2 32766: from all lookup main 32767: from all lookup default and when i run 'ip route' , i get the following: default via 168.87.147.1 dev eth0 proto static metric 1024 10.20.50.0/24 dev eth1 proto kernel scope link src 10.20.50.90 168.87.147.0/24 dev eth0 proto kernel scope link src 168.87.147.33 yet when I try to ping from another server to 10.20.50.90 it will not ping at all. Also, whenever I reboot the VM, eth1 switches over to DHCP and I lose my IP configuration. After I reset the IP Configuration back to Manual and reenter the IP, Centos creates a new interface file called ifcfg-Wired_Connection-1 and places the IP configuration for the interface into that file. Both virtual NICs are set to Static Mac Addresses, so I dont know why it keeps creating another interface file. Any ideas on what I am doing wrong here? All help is greatly appreciated! Thanks!