On 08/09/2017 10:44 PM, mad.scientist.at.large at tutanota.com wrote: > what file system are you using? ssd drives have different characteristics that need to be accomadated (including a relatively slow write process which is obvious as soon as the buffer is full), and never, never put a swap partition on it, the high activity will wear it out rather quickly. might also check cables, often a problem particularly if they are older sata cables being run at a possibly higher than rated speed. When working with a Cubieboard SoC (or most of the other armv7 boards), you tend to have everything hanging out: http://medon.htt-consult.com/~rgm/cubieboard/cubietower-2.JPG I have checked the cables and they are all tight. > in any case, reformating it might not be a bad idea, and you can always use the command line program badblocks to exercise and test it. I will have to look into that. > keep in mind the drive will invisibly remap any bad sectors if possible. if the reported size of the drive is smaller than it should be the drive has run out of spare blocks and dying blocks are being removed from the storage place with no replacements. > > -- > Securely sent with Tutanota. Claim your encrypted mailbox today! > https://tutanota.com > > 9. Aug 2017 18:44 by eliezer at ngtech.co.il: > > >> I have yet to see a SSD read\write error which wasn't related to disk issues >> like a bad sector but the controller might have an issue with the drive. >> To verify it you will need to burn some read\write IOPS of the drive but if >> it's under warranty then it's better to verify it now then later. >> >> Eliezer >> >> ---- >> Eliezer Croitoru >> Linux System Administrator >> Mobile: +972-5-28704261 >> Email: > eliezer at ngtech.co.il >> >> >> >> -----Original Message----- >> From: CentOS [> mailto:centos-bounces at centos.org> ] On Behalf Of Robert >> Moskowitz >> Sent: Wednesday, August 9, 2017 17:03 >> To: CentOS mailing list <> centos at centos.org> > >> Subject: [CentOS] Errors on an SSD drive >> >> I am building a new system using an Kingston 240GB SSD drive I pulled >> from my notebook (when I had to upgrade to a 500GB SSD drive). Centos >> install went fine and ran for a couple days then got errors on the >> console. Here is an example: >> >> [168176.995064] sd 0:0:0:0: [sda] tag#14 FAILED Result: >> hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK >> [168177.004050] sd 0:0:0:0: [sda] tag#14 CDB: Read(10) 28 00 01 04 68 b0 >> 00 00 08 00 >> [168177.011615] blk_update_request: I/O error, dev sda, sector 17066160 >> [168487.534510] sd 0:0:0:0: [sda] tag#17 FAILED Result: >> hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK >> [168487.543576] sd 0:0:0:0: [sda] tag#17 CDB: Read(10) 28 00 01 04 68 b0 >> 00 00 08 00 >> [168487.551206] blk_update_request: I/O error, dev sda, sector 17066160 >> [168787.813941] sd 0:0:0:0: [sda] tag#20 FAILED Result: >> hostbyte=DID_BAD_TARGET driverbyte=DRIVER_OK >> [168787.822951] sd 0:0:0:0: [sda] tag#20 CDB: Read(10) 28 00 01 04 68 b0 >> 00 00 08 00 >> [168787.830544] blk_update_request: I/O error, dev sda, sector 17066160 >> >> Eventually, I could not do anything on the system. Not even a >> 'reboot'. I had to do a cold power cycle to bring things back. >> >> Is there anything to do about this or trash the drive and start anew? >> >> Thanks >> >> _______________________________________________ >> CentOS mailing list >> CentOS at centos.org >> https://lists.centos.org/mailman/listinfo/centos >> >> _______________________________________________ >> CentOS mailing list >> CentOS at centos.org >> https://lists.centos.org/mailman/listinfo/centos > _______________________________________________ > CentOS mailing list > CentOS at centos.org > https://lists.centos.org/mailman/listinfo/centos
