Discuss August 2009

discuss@lists.centos.org

282 participants
264 discussions

Cloud Computing
by Matt 12 Sep '09

12 Sep '09

Is anyone creating a cloud based on Centos yet? Ubuntu seems to be quite active there: http://www.ubuntu.com/products/whatisubuntu/serveredition/cloud/uec Matt

6 10

mod_mono on centos5?
by Dave 07 Sep '09

07 Sep '09

Hello, Does anyone have mod_mono rpm or srpm compiled for centos5? Thanks. Dave.

4 4

problem with udev when booting kernel 5.3 release 128.4.1
by Rob Kampen 05 Sep '09

05 Sep '09

Hi List, I am running a 64 bit 5.3 kernel on an intel mb and all has been well. Today I thought it would be okay to reboot so that the latest kernel was running - i.e move from 128.2.1 to 128.4.1 release. The system passes POST fine, grub passes control to the 128.4.1 kernel and the boot process is under way. after some 30 secs the system starts beeping - continuously. After I hooked up a monitor I find that udev does not come up with OK and thats when the system starts the beep beep beep ...... No logs to see ...... using grub to select 128.2.1 boot fine Any ideas? Thanks in advance for your words of wisdom and advice. Rob

3 6

Centos 5.3 install on gigabyte GA-MA790FX-UD5P motherboard
by Nathan Norton 02 Sep '09

02 Sep '09

Hi, I am having some difficulties installing centos 5.3 on the gigabyte GA-MA790FX-UD5P motherboard. Has anyone got centos booting on this motherboard? so far I have tried the following. + disabled the jmicron controller as this caused errors on booting JMB363 bad irq(0): will probe later error (this error caused the installation to stop at this point) + tested all components in another computer, they all work. + remove all unnecessary components from the pci bus. + power supply is not an issue since I have used a 850W PSU Basically what I am seeing is once the installation process starts and asks do i have another sata disk, and I select no the screen freezes at this point *every* single time, the screen is always blue with a couple of greek looking characters on the screen. No logs are left at this point in the installation, so it is making it difficult to diagnose. Today I installed the grml distribution and it worked with no issues, it uses a base kernel of 2.6.28. so there is nothing wrong with the hardware but centos still does not want to install on this motherboard. Anyone have any ideas? Nathan

4 3

looking for RAID 1+0 setup instructions?
by Rudi Ahlers 02 Sep '09

02 Sep '09

Hi, Can someone please assist met with some software RAID 1+0 setup instructions? I have searched the web, but couldn't find any. I found a lot of RAID 10 setup instructions, but it doesn't help me. -- Kind Regards Rudi Ahlers CEO, SoftDux Hosting Web: http://www.SoftDux.com Office: 087 805 9573 Cell: 082 554 7532

12 47

A couple questions about Wine
by Ron Blizzard 02 Sep '09

02 Sep '09

VirtualBox works great but, since I only really use one Windows program (an older, specialized word processor called Movie Magic Screenwriter), I'm thinking of using Wine to run it in CentOS and getting rid of the Windows virtual machine. But a couple questions: 1) If I run Wine, do I introduce security or performance issues? 2) Is there any difference between Michael Harris' Wine repository and the ones available through... wherever yum is picking it up? (Actually it looks like it has two or three versions listed.) Thanks for any recommendations. I like VirtualBox, but it seems like overkill. -- RonB -- Using CentOS 5.3

4 5

setup iptables to allow forwarding through eth1
by Peter Peltonen 01 Sep '09

01 Sep '09

I have a fresh installed CentOS 5.3 server which should route traffic between two networks like this: network A (Internet) -- eth0 (default gw) : server : eth1 -- network B (LAN) I have set in sysctl.conf net.ipv4.ip_forward = 1 and routing works fine like this. But when I switch on the iptables service (with default setup, configured when installing the server), routing stops working (or at least I cannot ping a server in network A from network B). I guess the firewall is stopping it, so I read http://www.centos.org/docs/5/html/5.2/Deployment_Guide/s1-firewall-ipt-fwd.… and issued the commands # iptables -A FORWARD -i eth1 -j ACCEPT # iptables -A FORWARD -o eth1 -j ACCEPT but that did not help. So I am asking: what is the correct iptables command to make forwarding work? Regards, Peter

3 3

Configuring the firewall on CentOS
by Timothy Murphy 01 Sep '09

01 Sep '09

Is there a CentOS equivalent to config-system-firewall in Fedora, allowing specified services to pass through? -- Timothy Murphy e-mail: gayleard /at/ eircom.net tel: +353-86-2336090, +353-1-2842366 s-mail: School of Mathematics, Trinity College, Dublin 2, Ireland

3 3

what is the best way to delete so many queue files?
by MontyRee 01 Sep '09

01 Sep '09

Hello, all. I found that so many unnessary queue files are saved at /var/spool/clientmqueue/ directory. I tested two way to delete these files. 1. # rm -rf /var/spool/clientmqueue/* 2. # cd /var/spool/clientmqueue/ ; find . | xargs rm -fv But this makes a few load of the system and took too much time to delete. What is the best way to delete fast without too much load? Thanks in advance. _________________________________________________________________ 암호를 잃어버렸을 때를 대비하여 미리 암호 확인용 메일 설정하세요! http://im.msn.co.kr/im/main/mainCoverDetail.asp?seq=2251&page=1&BbsCode=bbs…

7 6

Conntrack-tools for CentOS 4.8
by Matt Shields 01 Sep '09

01 Sep '09

Does anyone know where I can get an RPM of Conntrack-tools, libnetfilter_conntrack and libnfnetlink that work with CentOS 4.8? -matt http://www.sysadminvalley.com http://www.beantownhost.com http://www.linkedin.com/in/mattboston Stephen Leacock<http://www.brainyquote.com/quotes/authors/s/stephen_leacock.html> - "I detest life-insurance agents: they always argue that I shall some day die, which is not so."

2 1

Jump to page:

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss August 2009