----- Scott Silva ssilva@sgvwater.com wrote:
RYAN M. vAN GINNEKEN spake the following on 10/2/2006 1:04 PM:
Hello all this is my first post to this list so i would like to than
you all in advance for your time and consideration.
I am in the process of building a new server and have purchased some
used hardware. There seems to be some hardware issuses and i am hoping nothing was damaged during shipping. However i am in contact with intel and we are tring to figure out the exact problem via email.
So i have insalled centos 4 from the four CD set and have done all
the updates through the GUI. I must say a GUI in Linux land is nice have been working mostly on old FreeBSD boxes none of which have GUI installed. Anyways the above mentioned hardware is this
INTEL SR2300 CHASSIS INTEL SE7500WV2 MAINBOARD INTEL (DUAL) XEON P4 2GHZ CPU HP 1G ECC RAM ADAPTEC 29160LP SCSI CONTROLLER PROMISE FASTRAC 2000TX has nothing attached to it
anyhow.
I have four Seagate Cheetas 147G 10.6K SCSI harddrive most are
firmware version 0006 (been meaning to update this to 00007 before i go to production)
HERE IS MY PROBLEM =======================================
When i boot up the machine i get this error off the getgo
PCI unable to handle 64bit address space for
==========================================================
Everything seems to work fine but i am woundering before i go any
further should i be installing the 64bit version of Centos on this machine? Is there a 64 version of Centos? anyways any help or advice on this matter is greatly apprciated.
ps if anyone is familiar with this mainboard and hardware setup i
would love some insight as to the was the BIOS error event codes that this machine keeps spiting out at me mean.
Thank you in advance
Could you have a 32 bit PCI card in a 64 bit slot? It should work, but I would suspect it is the promise card. You could try moving it about and see what happens.
Umm it is a server board with full card hieght riser card plugged in to what i think is the 64 bit slot on the mainboard. Howerver nothing is in any of the slots on the riser card. There is also another halfhieght riser card that has the adaptec SCSI card plugged into it but that is all.
Also, I think that card has an onboard promise controller. So maybe try pulling the promise card, since nothing is attached.
Pretty sure the promise controller is built into the mainboard as the only card i can see plugged in is the Adaptec 29160LP. Cannot find a way to uplug or disable this card in the bios.
You could try any other cards that aren't needed to boot the system, adding them one at a time until you error again.
the error is there with the onboard fasttrac card and the SCSI card but the SCSI card is needed to boot centos. I also tried removing the full hieght riser card that had nothing pluged into it but still get the same error.
--
MailScanner is like deodorant... You hope everybody uses it, and you notice quickly if they don't!!!!
CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos
RYAN M. vAN GINNEKEN spake the following on 10/2/2006 3:57 PM:
----- Scott Silva ssilva@sgvwater.com wrote:
RYAN M. vAN GINNEKEN spake the following on 10/2/2006 1:04 PM:
Hello all this is my first post to this list so i would like to than
you all in advance for your time and consideration.
I am in the process of building a new server and have purchased some
used hardware. There seems to be some hardware issuses and i am hoping nothing was damaged during shipping. However i am in contact with intel and we are tring to figure out the exact problem via email.
So i have insalled centos 4 from the four CD set and have done all
the updates through the GUI. I must say a GUI in Linux land is nice have been working mostly on old FreeBSD boxes none of which have GUI installed. Anyways the above mentioned hardware is this
INTEL SR2300 CHASSIS INTEL SE7500WV2 MAINBOARD INTEL (DUAL) XEON P4 2GHZ CPU HP 1G ECC RAM ADAPTEC 29160LP SCSI CONTROLLER PROMISE FASTRAC 2000TX has nothing attached to it
anyhow.
I have four Seagate Cheetas 147G 10.6K SCSI harddrive most are
firmware version 0006 (been meaning to update this to 00007 before i go to production)
HERE IS MY PROBLEM =======================================
When i boot up the machine i get this error off the getgo
PCI unable to handle 64bit address space for
==========================================================
Everything seems to work fine but i am woundering before i go any
further should i be installing the 64bit version of Centos on this machine? Is there a 64 version of Centos? anyways any help or advice on this matter is greatly apprciated.
ps if anyone is familiar with this mainboard and hardware setup i
would love some insight as to the was the BIOS error event codes that this machine keeps spiting out at me mean.
Thank you in advance
Could you have a 32 bit PCI card in a 64 bit slot? It should work, but I would suspect it is the promise card. You could try moving it about and see what happens.
Umm it is a server board with full card hieght riser card plugged in to what i think is the 64 bit slot on the mainboard. Howerver nothing is in any of the slots on the riser card. There is also another halfhieght riser card that has the adaptec SCSI card plugged into it but that is all.
Also, I think that card has an onboard promise controller. So maybe try pulling the promise card, since nothing is attached.
Pretty sure the promise controller is built into the mainboard as the only card i can see plugged in is the Adaptec 29160LP. Cannot find a way to uplug or disable this card in the bios.
You could try any other cards that aren't needed to boot the system, adding them one at a time until you error again.
the error is there with the onboard fasttrac card and the SCSI card but the SCSI card is needed to boot centos. I also tried removing the full hieght riser card that had nothing pluged into it but still get the same error.
--
MailScanner is like deodorant... You hope everybody uses it, and you notice quickly if they don't!!!!
CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos
Looking at what looks to be the board you mention, both of the slots are PCI-X. Are the riser cards the proper ones for the board? As for the scsi card, it looks to be a 64 bit pci card. Does the board have built-in scsi or IDE? Intel made versions with either. Maybe you could boot from a live CD or floppy on the on-board controller, and see if it starts. If the only card installed is the scsi card, then I would have to suspect it. The problem is the board is tying to map in a pci cards address space into the memory map so the card can have i/o with the rest of the system. Is the system's bios up to date? PCI-X is supposed to be backward compatible with PCI, but some things just don't work that way.
-
RYAN M. vAN GINNEKEN -
Scott Silva