New subject: Wifi networking-Endgame (Was: wireless laptop configuration)

20 Aug 2008


      Sorin Srbu wrote:
From: centos-bounces@centos.org
[mailto:centos-bounces@centos.org] On Behalf Of Toshaan
Bharvani
Sent: Tuesday, August 19, 2008 4:24 PM
To: centos@centos.org
Subject: Re: [CentOS] wireless laptop configuration
Sorin
Srbu wrote:
From: centos-bounces@centos.org
[mailto:centos-bounces@centos.org]
  On Behalf Of Toshaan Bharvani
Sent: Tuesday, August 19, 2008 2:42 PM
To: centos@centos.org
Subject: Re: [CentOS] wireless laptop configuration
Steve
Huff wrote:
...
...
On Aug 19, 2008, at 5:04 AM, Sorin@Gmail wrote:
...
...
...
I'm using a 3Com 3CRWE154G72 IIRC, which according to the
hwconf's
using the
...
...
prism54 driver/firmware/whatever.
...
...
...
...
Would I maybe be better off reinstalling the whole shebang and
have
the
...
...
wifi-card inserted from start in order for the centos
installer to
...
...
see it
...
...
properly from the beginning?
...
...
...
before you do that, open a terminal, become root, and run
...
/usr/sbin/kudzu (while the wireless card is installed). that's the
...
program that does hardware detection; it may be able to sort out
your
...
issue.
...
...
-steve
...
or if kudzu for some reason doesn't cooperate (which is always on my
system)
become root
run : /sbin/modprobe prism54
run : dmesg | tail
and read whether it just says it has loaded the module (single line) or
detected will output a wlanX statement and you are in business
Isn’t
it implied that since ”prism54” is listed in /etc/sysconfig/hwconf
for the wifi-card that the module has been loaded already? Or is this
some of
the magical stuff that sometimes doesn’t happen for whatever reason? 8-)
/etc/sysconfig/hwconf
is the file kudzu
creates when of all detected hardware at startup and it related this
hardware
with drivers in the kernel
but certain drivers are modules in the kernel, wich need to be loaded
manually
or later when the system is already running
this can be done by method 1 explained here above or adding them in
/etc/modprobe.conf which makes it load the modules at startup
you will need to add the line (if it is not yet there) :
alias wlan0 prism54
you can check whether the module is loaded with : /sbin/lsmod | grep
prism54
  This is how
far I got with the above hints. For some reason I don’t have a wlan0,
but
instead a eth0. I did create an alias in Network Manager for eth0 >
wlan0.
Then I ran the below modprobe command according to the below.
  “[root@centos-v5-x86 ~]# /sbin/modprobe prism54
  [root@centos-v5-x86 ~]# dmesg|tail
  eth0: resetting device...
  eth0: uploading firmware...
  prism54: request_firmware() failed for 'isl3890'
  eth0: could not upload firmware ('isl3890')
  eth0: islpci_reset: failure
  eth0: resetting device...
  eth0: uploading firmware...
  prism54: request_firmware() failed for 'isl3890'
  eth0: could not upload firmware ('isl3890')
  eth0: islpci_reset: failure
  [root@centos-v5-x86
~]#”
“When
I try to activate wlan0, I get this message:
  Error for wireless request "Set Bit Rate" (8B20) :
   SET failed on device eth0 ; Input/output error.
  Determining IP information for eth0...SIOCSIFFLAGS: No
such file or
directory
  SIOCSIFFLAGS: No such file or directory
   failed.”
  In /etc/modprobe.conf
I’ve added the line “alias wlan0 prism54”.
  What’s
more, I went to the prism54.org site and found a firmware, downloaded
it and as
per instructed on the site, renamed the .arm-file to isl3890 and put it
in /usr/lib/hotplug/firmware.
  Upon
restarting and activating wlan0 I still get the above SIOC-error.
  I have a
hunch this might actually work if I put the isl3890-file in the correct
place.
Not sure /usr/lib/hotplug/firmware *is* actually right, as I had
to
create the hotplugs and firmware-folders.
  Any hints on
this guys?
  TIA.
_______________________________________________
CentOS mailing list
CentOS@centos.org
http://lists.centos.org/mailman/listinfo/centos
you have used the following :
2.5.2.0.arm :
http://daemonizer.de/prism54/prism54-fw/fw-softmac/2.5.2.0.arm
Version 2.5.2.0 built on Thu Mar 4 16:05:03 CET 2004 by
inlbuild@tix
87a5519d70c16991b8fff9b3b31de68e
headers
Source: 3CRWE154G72_Jul_08_04.exe
try renaming to isl3886 as it is a pcmcia card so it is equal to
a pci version and then put in in /lib/firmware
_________________________________________________________________
Invite your mail contacts to join your friends list with Windows Live Spaces. It's easy!
http://spaces.live.com/spacesapi.aspx?wx_action=create&wx_url=/friends.a...