Hi folks,
I inherited a very old computer (I guess about 8 years old) which I'd like to use for some training on CentOS. I downloaded images for CentOS 6.4 i386 (DVD 1 and 2) and burned them onto discs. After inserting DVD 1 into drive and booting, on the "Welcome to CentOS 6.4!" screen I select "Install or upgrade an existing system". I then skip the media test and start the installation. Then I get a graphical installer where I choose english language and U.S. international keyboard layout.
Then I'm questioned about "What type of devices will your installation involve"? where I select "Basic Storage Devices" and then proceed. I get a dialog "Examining devices" with the message "Examining storage devices".
After a short while a dialog "No disks found" appears displaying the message "No usable disks have been found". I then go back and choose "Specialized Storage Devices" but I then get the same result (no devices are found).
Just to be sure that there are disks available and hardware works I installed a current Debian which works fine. From the BIOS and from Debian shell command "dmesg | grep -i ata" I see that there are two "Maxtor 6Y120L0" installed. Find output of "dmsg" below that email.
Is it possible and what steps are necessary to install CentOS 6.4 on that "Maxtor 6Y120L0" hard disks?
Regards,
Meikel
---
Output of "dmesg | grep -i ata"
[ 1.690559] pata_via 0000:00:11.1: version 0.3.4 [ 1.690591] pata_via 0000:00:11.1: can't derive routing for PCI INT A [ 1.693019] scsi0 : pata_via [ 1.693396] scsi1 : pata_via [ 1.694434] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xa800 irq 14 [ 1.694442] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xa808 irq 15 [ 1.864541] ata1.00: ATA-7: Maxtor 6Y120L0, YAR41BW0, max UDMA/133 [ 1.864549] ata1.00: 240121728 sectors, multi 16: LBA [ 1.864737] ata1.01: ATA-7: Maxtor 6Y120L0, YAR41BW0, max UDMA/133 [ 1.864744] ata1.01: 240121728 sectors, multi 16: LBA [ 1.880389] ata1.00: configured for UDMA/133 [ 1.896439] ata1.01: configured for UDMA/133 [ 1.896738] scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y120L0 YAR4 PQ: 0 ANSI: 5 [ 1.897477] scsi 0:0:1:0: Direct-Access ATA Maxtor 6Y120L0 YAR4 PQ: 0 ANSI: 5 [ 2.068361] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-4167B, DL11, max UDMA/33 [ 2.068375] ata2.01: ATAPI: CD-956E/AKV, A99, max UDMA/33 [ 2.084228] ata2.00: configured for UDMA/33 [ 2.100283] ata2.01: configured for UDMA/33
Specialized storage devices are NAS or other remote storage array types of devices. So that is not a valid option on your stand-alone system. It looks like your hard drives are visible to the Linux Anaconda installer, but you may want to check BIOS configuration and verify that they are configured correctly there. Unplug the power connectors to the drives and reseat them, and data cables from both ends and reseat those as well. Ensure that the jumpers on these parallel ATA drives aer set soi one is "Master" and one is "Slave." Other options may work, but also may not. The "CS" option is to be avoided. Be certain that the Master is the drive you want to be /dev/sda and the Slave will be /dev/sdb.
Based on my experience the jumpers on the hard drives are the most likely cause of this problem.
AFAIK, there are no "special" steps to install CentOS on any particular local hard drive. So long as BIOS and jumpers are correct, it should "just install."
On 04/06/2014 09:25 AM, Meikel wrote:
Hi folks,
I inherited a very old computer (I guess about 8 years old) which I'd like to use for some training on CentOS. I downloaded images for CentOS 6.4 i386 (DVD 1 and 2) and burned them onto discs. After inserting DVD 1 into drive and booting, on the "Welcome to CentOS 6.4!" screen I select "Install or upgrade an existing system". I then skip the media test and start the installation. Then I get a graphical installer where I choose english language and U.S. international keyboard layout.
Then I'm questioned about "What type of devices will your installation involve"? where I select "Basic Storage Devices" and then proceed. I get a dialog "Examining devices" with the message "Examining storage devices".
After a short while a dialog "No disks found" appears displaying the message "No usable disks have been found". I then go back and choose "Specialized Storage Devices" but I then get the same result (no devices are found).
Just to be sure that there are disks available and hardware works I installed a current Debian which works fine. From the BIOS and from Debian shell command "dmesg | grep -i ata" I see that there are two "Maxtor 6Y120L0" installed. Find output of "dmsg" below that email.
Is it possible and what steps are necessary to install CentOS 6.4 on that "Maxtor 6Y120L0" hard disks?
Regards,
Meikel
Output of "dmesg | grep -i ata"
[ 1.690559] pata_via 0000:00:11.1: version 0.3.4 [ 1.690591] pata_via 0000:00:11.1: can't derive routing for PCI INT A [ 1.693019] scsi0 : pata_via [ 1.693396] scsi1 : pata_via [ 1.694434] ata1: PATA max UDMA/133 cmd 0x1f0 ctl 0x3f6 bmdma 0xa800 irq 14 [ 1.694442] ata2: PATA max UDMA/133 cmd 0x170 ctl 0x376 bmdma 0xa808 irq 15 [ 1.864541] ata1.00: ATA-7: Maxtor 6Y120L0, YAR41BW0, max UDMA/133 [ 1.864549] ata1.00: 240121728 sectors, multi 16: LBA [ 1.864737] ata1.01: ATA-7: Maxtor 6Y120L0, YAR41BW0, max UDMA/133 [ 1.864744] ata1.01: 240121728 sectors, multi 16: LBA [ 1.880389] ata1.00: configured for UDMA/133 [ 1.896439] ata1.01: configured for UDMA/133 [ 1.896738] scsi 0:0:0:0: Direct-Access ATA Maxtor 6Y120L0 YAR4 PQ: 0 ANSI: 5 [ 1.897477] scsi 0:0:1:0: Direct-Access ATA Maxtor 6Y120L0 YAR4 PQ: 0 ANSI: 5 [ 2.068361] ata2.00: ATAPI: HL-DT-ST DVDRAM GSA-4167B, DL11, max UDMA/33 [ 2.068375] ata2.01: ATAPI: CD-956E/AKV, A99, max UDMA/33 [ 2.084228] ata2.00: configured for UDMA/33 [ 2.100283] ata2.01: configured for UDMA/33
CentOS mailing list CentOS@centos.org http://lists.centos.org/mailman/listinfo/centos
--
David P. Both, RHCE Millennium Technology Consulting LLC 919-389-8678
dboth@millennium-technology.com
www.millennium-technology.com www.databook.bz - Home of the DataBook for Linux DataBook is a Registered Trademark of David Both
This communication may be unlawfully collected and stored by the National Security Agency (NSA) in secret. The parties to this email do not consent to the retrieving or storing of this communication and any related metadata, as well as printing, copying, re-transmitting, disseminating, or otherwise using it. If you believe you have received this communication in error, please delete it immediately.
On 4/6/2014 6:25 AM, Meikel wrote:
Just to be sure that there are disks available and hardware works I installed a current Debian which works fine. From the BIOS and from Debian shell command "dmesg | grep -i ata" I see that there are two "Maxtor 6Y120L0" installed. Find output of "dmsg" below that email.
Is it possible and what steps are necessary to install CentOS 6.4 on that "Maxtor 6Y120L0" hard disks?
thats a parallel ATA aka IDE drive? do you happen to know what sort of IDE controller it is plugged into? is the IDE properly configured, so the two drives (you *do* have two drives, right?) are the master on the end connector of a 80 wire cable (I note dmesg says UDMA133), and the slave is in the middle connector? IIRC, parallel IDE drives on UDMA100+ should be jumpered for 'cable select' and must use a cable that has a black, grey, and blue connector, where the black connector goes into the motherboard, the grey connector is for the slave drive, and the blue connector is for the master drive.
you might try booting the CentOS DVD into single user mode (linux single at the boot prompt), and at the shell, `dd if=/dev/zero of=/dev/sda bs=65536 count=65536', this should zero the first 4GB of the disk, it will take a minute or something. repeat with /dev/sdb for good luck.
frankly, any time spent on this is worth more than these drives. PATA is a closed chapter of computer history. SATA took over starting 10 years ago.
-
David Both -
John R Pierce -
Meikel