Discuss

discuss@lists.centos.org

34753 discussions

Re: CentOS Digest, Vol 45, Issue 23
by James B. Byrne 23 Oct '08

23 Oct '08

> > Message: 24 > Date: Thu, 23 Oct 2008 03:53:55 -0400 > From: "John" <jses27(a)gmail.com> > Subject: RE: [CentOS] OT: Setting a CentOS to gateway a private IP > address > To: "'CentOS mailing list'" <centos(a)centos.org> > Message-ID: <86C552A83B964E6499972CEAD4610189@ethan27> > Content-Type: text/plain; charset="us-ascii" > > behalf of; James B. Byrne [byrnejb(a)harte-lyne.ca] > > router rip > network eth0 <--- is this correct? > network 192.168.219.0/24 > ##################################### > JohnStanley Writes: > Did you bother to check the documentation? > > http://www.quagga.net/docs/docs-info.php#SEC40 > As always, yes I did, albeit the pdf version. Like much documentation, it is possibly a wonderful aide memoire for somebody who knows the subject intimately but it is a little terse and somewhat sparse for someone with no prior knowledge and little time. The difficulty that I need to address is what ripd configuration provides rip info regarding 192.168.219.0/24 connected via eth1 out to all networks connected via 2xx.yyy.zzz.0/24 on eth0. Must I configure a virtual IP from 192.168.219.0/24 on eth0 as well as eth1 or not? Do I just set ripd.conf to: router rip network 192.168.219.0/24 Is that all that is required? Recall that the purpose of this exercise is to simultaneously provide interim public and private ipv4 address connectivity on the same physical lan behind our Internet router. The long term objective is to remove the public address space from the lan. At that point this finessing becomes unnecessary. For example: INET Router: eth0 IP 2xx.yyy.bbb.64 eth1 IP 2xx.yyy.zzz.1 IP 192.168.71.1 ip 10.0.0.1 network 2xx.yyy.zzz.0/24 network 192.168.0.0/16 network 10.0.0.0/8 host1: eth0 IP 2xx.yyy.zzz.22 host2: eth0 IP 2xx.yyy.zzz.23 eth1 IP 192.168.219.1 host3: eth0 IP 192.168.219.102 host4: eth0 IP 192.168.71.65 INET Router <<-------->> SWITCH host1/eth0 <<--------->> SWITCH host2/eth0 <<--------->> SWITCH host2/eth1 <<--------->> HUB host3/eth0 <<--------->> HUB host4/eth0 <<--------->> SWITCH How do I set up ripd on host2 so that host4 (192.168.71.65) reaches host3 (192.168.219.102) via host2 (2xx.yyy.zzz.23)? Clearly the ripd info for 192.168.219.0/24 must go out 216.185.71.23 but I am unclear as to what ripd.conf configuration settings accomplish this. -- *** E-Mail is NOT a SECURE channel *** James B. Byrne mailto:ByrneJB@Harte-Lyne.ca Harte & Lyne Limited http://www.harte-lyne.ca 9 Brockley Drive vox: +1 905 561 1241 Hamilton, Ontario fax: +1 905 561 0757 Canada L8E 3C3

1 0

compare directories
by David Hláčik 23 Oct '08

23 Oct '08

Hello guys, I have two mirrors. I need to compare files and directories on both mirrors and as a result print list of those which are missing on mirror 2 What i did find /data > find.mirror1 find /data > find.mirror2 Now i need to get list of those directories which are missing in mirror1. Thanks in advance! David

5 4

KIVIO
by Gopinath Achari 23 Oct '08

23 Oct '08

Hi all, I need Koffice-kivio package for centos 5.2 (i386) I downloaded this package from kde.org site. when i installed. It generated lots of dependency errors even though the dependency packages are installed please Help me out . I need kivio ( Equivalent to Visio) regards, Gopinath M.

3 2

strict memory
by Mag Gam 23 Oct '08

23 Oct '08

Hello All: Running 5.2 at our university. We have several student's processes that take up too much memory. Our system have 64G of RAM and some processes take close to 32-48G of RAM. This is causing many problems for others. I was wondering if there is a way to restrict memory usage per process? If the process goes over 32G simply kill it. Any thoughts or ideas? TIA

5 8

Creating a controlled local repo
by Sorin Srbu 23 Oct '08

23 Oct '08

Hi all, I've been thinking about creating a local repo for our to-be CentOS-park (we're currently in the process of migrating from RHEL3 to CentOS5). As we need to control all updates being applied (think WUS, Windows Update Server) because of special software being run on servers and clients, we must check first that our molecular modeling software doesn't bite the grass should eg X, the kernel (and breaking the proprietary nvidia gfx-drivers in the process) etc be updated in a "non-approved" way. Therefore I've planned to create a local repo on one of our servers, share /var/cache/yum, set keepcache to 1 on that server and have it reposync periodically (like once a week) with CentOS Base, Extras, rpmforge and so on. On the clients I'd disable all standard repos, and only have the clients yum update from the aforementioned local repo server. Would this work? Or is there a cleaner/nicer/better/simpler way to do this? Gotchas' maybe? Any feedback is appreciated. Thx in advance. -- BW, Sorin ----------------------------------------------------------- # Sorin Srbu [Sysadmin] # Dept of Medicinal Chemistry, Phone: +46 (0)18-4714482 >3 signals> GSM # Div of Org Pharm Chem, Mobile: +46 (0)701-718023 # Box 574, Uppsala University, Fax: +46 (0)18-4714482 # SE-751 23 Uppsala, Sweden Visit: BMC, Husargatan 3, D5:512b # Web: http://www.orgfarm.uu.se ----------------------------------------------------------- # () ASCII ribbon campaign - Against html E-mail # /\ # # MotD follows: # Wit levels low. Attempting to compensate.

2 4

Redhat enterprise rpm
by ann kok 23 Oct '08

23 Oct '08

Hi all We are difficult to get rpm in our system running redhat enterpirse Can you use the centos rpm to install in redhat eneterprise? ARe they compatible? Thank you

4 3

i would like to add asterix to my centos
by david fritz 23 Oct '08

23 Oct '08

I want to add a server of VoIP under my server, but I don't have de doawnload and i don't have the tutotrial. please help me

5 4

SCSI error: return code = 0x10070000
by partha chowdhury 23 Oct '08

23 Oct '08

I have just bought a 120GB external usb drive but after plugging it in it is not getting mounted. lines from /var/log/messages: > Oct 22 18:54:49 station2 kernel: usb 1-2: new high speed USB device using ehci_hcd and address 2 > Oct 22 18:54:49 station2 kernel: usb 1-2: configuration #1 chosen from 1 choice > Oct 22 18:54:49 station2 kernel: scsi4 : SCSI emulation for USB Mass Storage devices > Oct 22 18:54:54 station2 kernel: Vendor: ST312002 Model: 2A Rev: 0 0 > Oct 22 18:54:54 station2 kernel: Type: Direct-Access ANSI SCSI revision: 00 > Oct 22 18:54:54 station2 kernel: SCSI device sdd: 234441648 512-byte hdwr sectors (120034 MB) > Oct 22 18:54:54 station2 kernel: sdd: Write Protect is off > Oct 22 18:54:54 station2 kernel: sdd: assuming drive cache: write through > Oct 22 18:54:54 station2 kernel: SCSI device sdd: 234441648 512-byte hdwr sectors (120034 MB) > Oct 22 18:54:54 station2 kernel: sdd: Write Protect is off > Oct 22 18:54:54 station2 kernel: sdd: assuming drive cache: write through > Oct 22 18:54:54 station2 kernel: sdd:<6>sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: Dev sdd: unable to read RDB block 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error, dev sdd, sector 0 > Oct 22 18:54:54 station2 kernel: Buffer I/O error on device sdd, logical block 0 > Oct 22 18:54:54 station2 kernel: unable to read partition table > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: Attached scsi disk sdd > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: Attached scsi generic sg3 type 0 > Oct 22 18:54:54 station2 kernel: sd 4:0:0:0: SCSI error: return code = 0x10070000 > Oct 22 18:54:54 station2 kernel: end_request: I/O error upon searching in the forum i came accross this tread http://www.centos.org/modules/newbb/viewtopic.php?topic_id=9887&forum=29&po… but it has gone unanswered for two years. Google search gives result all of which involves moving to a newer kernel.For the matter the drive gets mounted under fedora 9 - but i want to use it with CentOS. here is my lspci -v > 00:00.0 RAM memory: nVidia Corporation MCP67 Memory Controller (rev a2) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, latency 0 > Capabilities: [44] HyperTransport: Slave or Primary Interface > Capabilities: [dc] HyperTransport: MSI Mapping > > 00:01.0 ISA bridge: nVidia Corporation MCP67 ISA Bridge (rev a2) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, latency 0 > I/O ports at 0900 [size=256] > > 00:01.1 SMBus: nVidia Corporation MCP67 SMBus (rev a2) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: 66MHz, fast devsel, IRQ 10 > I/O ports at dc00 [size=64] > I/O ports at 0600 [size=64] > I/O ports at 0700 [size=64] > Capabilities: [44] Power Management version 2 > > 00:02.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 58 > Memory at feaff000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [44] Power Management version 2 > > 00:02.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 233 > Memory at feafec00 (32-bit, non-prefetchable) [size=256] > Capabilities: [44] Debug port > Capabilities: [80] Power Management version 2 > > 00:04.0 USB Controller: nVidia Corporation MCP67 OHCI USB 1.1 Controller (rev a2) (prog-if 10 [OHCI]) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 66 > Memory at feafd000 (32-bit, non-prefetchable) [size=4K] > Capabilities: [44] Power Management version 2 > > 00:04.1 USB Controller: nVidia Corporation MCP67 EHCI USB 2.0 Controller (rev a2) (prog-if 20 [EHCI]) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 50 > Memory at feafe800 (32-bit, non-prefetchable) [size=256] > Capabilities: [44] Debug port > Capabilities: [80] Power Management version 2 > > 00:08.0 PCI bridge: nVidia Corporation MCP67 PCI Bridge (rev a2) (prog-if 01 [Subtractive decode]) > Flags: bus master, 66MHz, fast devsel, latency 0 > Bus: primary=00, secondary=01, subordinate=01, sec-latency=64 > I/O behind bridge: 0000e000-0000efff > Memory behind bridge: feb00000-febfffff > Capabilities: [b8] #0d [0000] > Capabilities: [8c] HyperTransport: MSI Mapping > > 00:09.0 IDE interface: nVidia Corporation MCP67 AHCI Controller (rev a2) (prog-if 85 [Master SecO PriO]) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 233 > I/O ports at d480 [size=8] > I/O ports at d400 [size=4] > I/O ports at d080 [size=8] > I/O ports at d000 [size=4] > I/O ports at cc00 [size=16] > Memory at feafa000 (32-bit, non-prefetchable) [size=8K] > Capabilities: [44] Power Management version 2 > Capabilities: [8c] #12 [0010] > > 00:0a.0 Ethernet controller: nVidia Corporation MCP67 Ethernet (rev a2) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, latency 0, IRQ 90 > Memory at feafc000 (32-bit, non-prefetchable) [size=4K] > I/O ports at c880 [size=8] > Memory at feafe400 (32-bit, non-prefetchable) [size=256] > Memory at feafe000 (32-bit, non-prefetchable) [size=16] > Capabilities: [44] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/3 Enable+ > Capabilities: [6c] HyperTransport: MSI Mapping > > 00:0b.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=02, subordinate=02, sec-latency=0 > Capabilities: [40] #0d [0000] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping > Capabilities: [80] Express Root Port (Slot+) IRQ 0 > 00:0c.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=03, subordinate=03, sec-latency=0 > Capabilities: [40] #0d [0000] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping > Capabilities: [80] Express Root Port (Slot+) IRQ 0 > > 00:0d.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=04, subordinate=04, sec-latency=0 > Capabilities: [40] #0d [0000] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping > Capabilities: [80] Express Root Port (Slot+) IRQ 0 > > 00:0e.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=05, subordinate=05, sec-latency=0 > Capabilities: [40] #0d [0000] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping > Capabilities: [80] Express Root Port (Slot+) IRQ 0 > > 00:0f.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=06, subordinate=06, sec-latency=0 > Capabilities: [40] #0d [0000] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping > Capabilities: [80] Express Root Port (Slot+) IRQ 0 > > 00:10.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=07, subordinate=07, sec-latency=0 > Capabilities: [40] #0d [0000] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping > Capabilities: [80] Express Root Port (Slot+) IRQ 0 > > 00:11.0 PCI bridge: nVidia Corporation MCP67 PCI Express Bridge (rev a2) (prog-if 00 [Normal decode]) > Flags: bus master, fast devsel, latency 0 > Bus: primary=00, secondary=08, subordinate=08, sec-latency=0 > Capabilities: [40] #0d [0000] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/1 Enable+ > Capabilities: [60] HyperTransport: MSI Mapping > Capabilities: [80] Express Root Port (Slot+) IRQ 0 > > 00:12.0 VGA compatible controller: nVidia Corporation GeForce 7050 PV / nForce 630a (rev a2) (prog-if 00 [VGA controller]) > Subsystem: ASUSTeK Computer Inc. Unknown device 82b3 > Flags: bus master, 66MHz, fast devsel, laten > Memory at fd000000 (32-bit, non-prefetchable) [size=16M] > Memory at d0000000 (64-bit, prefetchable) [size=256M] > Memory at fc000000 (64-bit, non-prefetchable) [size=16M] > [virtual] Expansion ROM at feac0000 [disabled] [size=128K] > Capabilities: [48] Power Management version 2 > Capabilities: [50] Message Signalled Interrupts: 64bit+ Queue=0/0 Enable- > > 00:18.0 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] HyperTransport Technology Configuration > Flags: fast devsel > Capabilities: [80] HyperTransport: Host or Secondary Interface > > 00:18.1 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Address Map > Flags: fast devsel > > 00:18.2 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] DRAM Controller > Flags: fast devsel > > 00:18.3 Host bridge: Advanced Micro Devices [AMD] K8 [Athlon64/Opteron] Miscellaneous Control > Flags: fast devsel > Capabilities: [f0] #0f [0010] > > 01:06.0 Multimedia audio controller: Creative Labs [SB Live! Value] EMU10k1X > Subsystem: Creative Labs Unknown device 1001 > Flags: bus master, medium devsel, latency 64, IRQ 82 > I/O ports at ec00 [size=32] > Capabilities: [dc] Power Management version 2 > > 01:07.0 Ethernet controller: VIA Technologies, Inc. VT6105 [Rhine-III] (rev 8b) > Subsystem: D-Link System Inc Unknown device 1405 > Flags: bus master, medium devsel, latency 64, IRQ 74 > I/O ports at e800 [size=256] > Memory at febffc00 (32-bit, non-prefetchable) [size=256] > Capabilities: [44] Power Management version 2

2 7

KDE Versions in CentOS ?
by kevin kempter 22 Oct '08

22 Oct '08

HI LIst; What version of KDE is included in the latest version of CentOS ? Also, is there a way to get KDE4 in CentOS ? If so, Can I have both KDE3.x and KDE4 installed and switch back and forth between the 2 versions if needed ? Thanks in advance... /Kevin

5 6

showfoto, digikam - how to install
by kevin kempter 22 Oct '08

22 Oct '08

Hi List; where can I find the showfoto tool for CentOS v5 ? do I need to enable another yum repo somewhere? Thanks in advance

3 2

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss