Discuss

discuss@lists.centos.org

34758 discussions

CentOS 3.8 and ESS ES1878 sound chip?
by Aleksandar Milivojevic 19 Oct '06

19 Oct '06

-----BEGIN PGP SIGNED MESSAGE----- Hash: SHA1 Hi, I can't seem to be able to get any sound out of my CentOS 3.8 laptop. I have the ESS ES1878 chip in it. It can work in either native mode, or in SoundBlaster compatible mode. Neither is detected by CentOS 3.8. I've looked at the directory with kernel drivers, and there doesn't seem to be any kernel module that smells like either ES1878 or SoundBlaster. -----BEGIN PGP SIGNATURE----- Version: GnuPG v1.4.5 (MingW32) iD8DBQFFNvoJSuSa4NZgqj8RAuKkAJ93l+8eemXrDuaBrufXibAc+vpn3gCaA4q7 7NB3nVCGqim784gQsUxyl5Q= =Eje+ -----END PGP SIGNATURE-----

1 1

RE: [CentOS] Switch to Nvidia from ATI
by Bisbal, Prentice 18 Oct '06

18 Oct '06

Alfred, You can use xvidtune or gtf to generate modelines. Both should be included with your distribution. It's been a while since I used them, so check the man pages for how to use them. nvidia-installer should be installed when you run NVIDIA-Linux-x86-1.0-XXXX-pkg1.run. Do 'locate nvidia-installer' or 'which nvidia-installer'. It should be installed in /usr/bin -- Prentice -----Original Message----- From: centos-bounces(a)centos.org [mailto:centos-bounces@centos.org] On Behalf Of Alfred von Campe Sent: Wednesday, October 18, 2006 4:41 PM To: CentOS mailing list Subject: Re: [CentOS] Switch to Nvidia from ATI On Oct 18, 2006, at 14:42, Jay Leafey wrote: > Since you've already gone to the nVidia card it's a little late, I > know, but one of my Dell workstations has a similar display chip > (Intel 915G) and I was able to drive my Dell 2100fp at 1600x1200@60Hz > by making a couple of changes in the xorg.conf file. > Specifically, in the "Monitor" section I added a modeline for the that > resolution with some different timings: > > ModeLine "1600x1200" 160.0 1600 1664 1856 2160 1200 1201 > 1204 1250 > > Then in the "Screen" section I added 1600x1200 to the "Modes" line: > > Modes "1600x1200" "1280x1024" "1280x960" "1152x864" > "1024x768" "800x600" "640x480" That's good to know for the future. But how did you come up with those numbers for the ModeLine entry? I played around with the HorizSync and VertRefresh entries to no avail. > It's not that hard, thankfully. You can specify the kernel version to > the installer script, as well as just installing a new kernel module > rather than a full reinstall: > > /usr/local/bin/nvidia-installer --kernel-module-only --kernel- > name=(kernel version) > > For example, when the new kernel (kernel-2.6.9-42.0.3.plus.c4) came > out, I just ran this command before rebooting to the new kernel: > > /usr/local/bin/nvidia-installer --kernel-module-only --kernel- > name=2.6.9-42.0.3.plus.c4 I have not installed the nvidia-installer, but rather I run the NVIDIA-Linux-x86-1.0-XXXX-pkg1.run script with the -s option (silent) after rebuilding it with the --add-this-kernel option. > It does require that the kernel-devel{,-smp} package be installed for > the kernel for which you want to rebuild the driver, but that's not > really a problem for me. I've been trying to figure out how to make > this happen at boot-time before starting X, but haven't pursued it too > hard. I got this to work, but it was a bit of a hack. I'll contact you off list with the details. Alfred _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos The contents of this communication, including any attachments, may be confidential, privileged or otherwise protected from disclosure. They are intended solely for the use of the individual or entity to whom they are addressed. If you are not the intended recipient, please do not read, copy, use or disclose the contents of this communication. Please notify the sender immediately and delete the communication in its entirety.

1 0

CUPS Problem
by Akemi Yagi 18 Oct '06

18 Oct '06

When setting up a raw queue on the CentOS box, it might be necessary to edit couple of files in /etc/cups. mime.convs - uncomment this line: #application/octet-stream application/vnd.cups-raw 0 - mime.types - uncomment this line: #application/octet-stream

4 3

RE: [CentOS] Re: Switch to Nvidia from ATI
by Bisbal, Prentice 18 Oct '06

18 Oct '06

I'm using a dual-headed setup w/ the NVIDIA driver and it works fine, even with hardware 3D stereo. BTW - I'm using RHEL3WS. I haven't switched to CentOS yet. I subscribed before making the switch. -- Prentice -----Original Message----- From: centos-bounces(a)centos.org [mailto:centos-bounces@centos.org] On Behalf Of Mauricio Tavares Sent: Wednesday, October 18, 2006 1:10 PM To: centos(a)centos.org Subject: [CentOS] Re: Switch to Nvidia from ATI Jay Leafey wrote: > BRUCE STANLEY wrote: >> I am having some issues (e.g. System lock ups) with my ATI 9250 Video >> card. >> >> I am thinging about replacing it with either a Nvidia >> >> FX5200, FX5500, or a FX5600 card. >> >> Is anyone using one of these cards on Centos 4.1 with the stock >> (XORG) nv driver? >> > > I'm currently using an nVidia FX 5600 card on my workstation running > CentOS 4.4. I used the XORG nv driver for a while with good, stable > results, but switched to the nVidia-provided driver for better 3D > performance. Gotta be able to play Quake 4, don't you know! > > For anything that does not require 3D, tho, the nv driver seems to > work just fine. How about dual head setup? _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos The contents of this communication, including any attachments, may be confidential, privileged or otherwise protected from disclosure. They are intended solely for the use of the individual or entity to whom they are addressed. If you are not the intended recipient, please do not read, copy, use or disclose the contents of this communication. Please notify the sender immediately and delete the communication in its entirety.

1 0

RE: [CentOS] Switch to Nvidia from ATI
by Bisbal, Prentice 18 Oct '06

18 Oct '06

If you're going to do that, you definitely want to tweak the settings for Full-Scene Anti-Aliasing (FSAA). How to do that is documented somewhere in the NVidia-supplied documentation. Using Unreal Tournament, as a test case, I set FSAA to the most intensive algorithms, set the resolution to the highest that UT supported, and still had ridiculously high frame rates and ultra-smooth animation! -- Prentice -----Original Message----- From: centos-bounces(a)centos.org [mailto:centos-bounces@centos.org] On Behalf Of chrism(a)imntv.com Sent: Wednesday, October 18, 2006 1:38 PM To: CentOS mailing list Subject: Re: [CentOS] Switch to Nvidia from ATI Bisbal, Prentice wrote: > We use NVidia cards to do 3D hardware stereo graphics to view > molecules in 3D. The 3D perfomance after upgrading to the > NVidia-supplied driver is mind-blowing. > You are just trying to get me to download quake for linux! A pox on you, I say! ;-) _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos The contents of this communication, including any attachments, may be confidential, privileged or otherwise protected from disclosure. They are intended solely for the use of the individual or entity to whom they are addressed. If you are not the intended recipient, please do not read, copy, use or disclose the contents of this communication. Please notify the sender immediately and delete the communication in its entirety.

1 0

yum repository and createrepo
by Akemi Yagi 18 Oct '06

18 Oct '06

*Ken Leyba wrote:* >I've setup a local yum repository for about 25 workstations and I'm >using rsync from a local mirror. Do I need to create my own XML >headers, i.e. the 'repodata' directory, or since I'm syncing the whole >updates directory can I use the 'repodata' directory from the mirror? Yes, that should be fine if you rsync the whole thing. >I also have a question on using createrepo. The directory layout is: > >~/updates/ >~/updates/headers/ >~/updates/repodata/ >~/updates/RPMS/ > >If I do the following in the 'updates' directory: > ># createrepo -v ./RPMS > >The 'repodata' diretcory is created under the 'RPMS' directory and not >the current 'updates' directory. How can I have the 'repodata' >directory created/updated in the correct directory under 'updates'? You need to run |createrepo| against the directory under which you want the |repodata| directory to appear. In your case run: createrepo ~/updates

2 1

Kickstart with a VLAN interface
by Gary Richardson 18 Oct '06

18 Oct '06

Hey, Is it possible to configure various vlan interfaces via a kickstart install? For example: # vlan 101 network --device eth0.101 --bootproto static --ip=10.10.10.10 --netmask= 255.255.255.0 # vlan 102 network --device eth0.102 --bootproto static --ip=10.11.11.11 --netmask= 255.255.255.0 Thanks.

1 0

RE: [CentOS] Switch to Nvidia from ATI
by Bisbal, Prentice 18 Oct '06

18 Oct '06

We use NVidia cards to do 3D hardware stereo graphics to view molecules in 3D. The 3D perfomance after upgrading to the NVidia-supplied driver is mind-blowing. -- Prentice -----Original Message----- From: centos-bounces(a)centos.org [mailto:centos-bounces@centos.org] On Behalf Of chrism(a)imntv.com Sent: Wednesday, October 18, 2006 12:58 PM To: CentOS mailing list Subject: Re: [CentOS] Switch to Nvidia from ATI Jay Leafey wrote: > > I'm currently using an nVidia FX 5600 card on my workstation running > CentOS 4.4. I used the XORG nv driver for a while with good, stable > results, but switched to the nVidia-provided driver for better 3D > performance. Gotta be able to play Quake 4, don't you know! > > For anything that does not require 3D, tho, the nv driver seems to > work just fine. I agree 100%. I only updated to the nvidia-supplied driver on a couple of machines because "it was there" not because the stock driver was slow or broken. I haven't even tried the 3D performance...I'll have to get right on that. ;) Cheers, _______________________________________________ CentOS mailing list CentOS(a)centos.org http://lists.centos.org/mailman/listinfo/centos The contents of this communication, including any attachments, may be confidential, privileged or otherwise protected from disclosure. They are intended solely for the use of the individual or entity to whom they are addressed. If you are not the intended recipient, please do not read, copy, use or disclose the contents of this communication. Please notify the sender immediately and delete the communication in its entirety.

2 1

APIC error on CPU0: 60(60)
by Erick Perez 18 Oct '06

18 Oct '06

I have a lot of this errors in my Centos stock 4.3 version in an Intel D945gnt motherboard with a Pentium D (dual core) If I disable apic in the grub.conf (apic=off) will I get a performance hit? Im running Asterisk on that machine. 40 is Received Illegal Vector 20 is Send Illegal Vector 60 means you're getting both errors at the same time. Basically it means that the APIC bus messages are malformed. The cause can be hardware or software, it's difficult to tell. APIC error on CPU0: 60(60) APIC error on CPU0: 60(60) APIC error on CPU0: 60(60) cat /proc/cpuinfo shows: processor : 1 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Pentium(R) D CPU 2.66GHz stepping : 7 cpu MHz : 2666.770 cache size : 1024 KB physical id : 0 siblings : 2 core id : 1 cpu cores : 2 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm pni monitor ds_cpl tm2 cid cx16 xtpr bogomips : 5333.47 clflush size : 64 cache_alignment : 128 address sizes : 36 bits physical, 48 bits virtual power management: processor : 0 vendor_id : GenuineIntel cpu family : 15 model : 4 model name : Intel(R) Pentium(R) D CPU 2.66GHz stepping : 7 cpu MHz : 2666.770 cache size : 1024 KB physical id : 0 siblings : 2 core id : 0 cpu cores : 2 fpu : yes fpu_exception : yes cpuid level : 5 wp : yes flags : fpu vme de pse tsc msr pae mce cx8 apic sep mtrr pge mca cmov pat pse36 clflush dts acpi mmx fxsr sse sse2 ss ht tm syscall nx lm pni monitor ds_cpl tm2 cid cx16 xtpr bogomips : 5338.11 clflush size : 64 cache_alignment : 128 address sizes : 36 bits physical, 48 bits virtual power management: -- ------------------------------------------------------------ Erick Perez Panama Sistemas Integradores de Telefonia IP y Soluciones Para Centros de Datos Panama, Republica de Panama Cel Panama. +(507) 6694-4780 mailto: eaperezh(a)gmail.com mailto: eperez(a)ptysystems.com ------------------------------------------------------------

5 6

CentOS-announce Digest, Vol 20, Issue 6
by centos-announce-request＠centos.org 18 Oct '06

18 Oct '06

Send CentOS-announce mailing list submissions to centos-announce(a)centos.org To subscribe or unsubscribe via the World Wide Web, visit http://lists.centos.org/mailman/listinfo/centos-announce or, via email, send a message with subject or body 'help' to centos-announce-request(a)centos.org You can reach the person managing the list at centos-announce-owner(a)centos.org When replying, please edit your Subject line so it is more specific than "Re: Contents of CentOS-announce digest..." Today's Topics: 1. CESA-2006:0720 Critical CentOS 3 i386 kdelibs - security update (Tru Huynh) 2. CESA-2006:0720 Critical CentOS 3 x86_64 kdelibs - security update (Tru Huynh) ---------------------------------------------------------------------- Message: 1 Date: Wed, 18 Oct 2006 12:37:38 +0200 From: Tru Huynh <tru(a)centos.org> Subject: [CentOS-announce] CESA-2006:0720 Critical CentOS 3 i386 kdelibs - security update To: centos-announce(a)centos.org Message-ID: <20061018103738.GA25574(a)sillage.bis.pasteur.fr> Content-Type: text/plain; charset="us-ascii" CentOS Errata and Security Advisory CESA-2006:0720 kdelibs security update for CentOS 3 i386: https://rhn.redhat.com/errata/RHSA-2006-0720.html The following updated file has been uploaded and is currently syncing to the mirrors: i386: updates/i386/RPMS/kdelibs-3.1.3-6.12.i386.rpm updates/i386/RPMS/kdelibs-devel-3.1.3-6.12.i386.rpm source: updates/SRPMS/kdelibs-3.1.3-6.12.src.rpm You may update your CentOS-3 i386 installations by running the command: yum update kdelibs\* Tru -- Tru Huynh (CentOS-3 i386/x86_64 Package Maintenance) http://pgp.mit.edu:11371/pks/lookup?op=get&search=0xBEFA581B

1 0

Jump to page:

2026

2025

2024

2023

2022

2021

2020

2019

2018

2017

2016

2015

2014

2013

2012

2011

2010

2009

2008

2007

2006

2005

2004

Discuss